Abstract: Aeration by a plunging water jet is an energetically attractive way to effect oxygen-transfer than conventional oxygenation systems. In the present study, a new type of conical shaped plunging aeration device is fabricated to generate hollow inclined ined plunging jets (jet plunge angle of π/3 ) to investigate its oxygen transfer capacity. The results suggest that the volumetric oxygen-transfer coefficient and oxygen-transfer efficiency of the conical plunging jet aerator are competitive with other types of aeration systems. Relationships of volumetric oxygen-transfer coefficient with jet power per unit volume and jet parameters are also proposed. The suggested relationships predict the volumetric oxygentransfer coefficient within a scatter of ± 15% . Further, the application of Support Vector Machines on the experimental data revealed its utility in the prediction of volumetric oxygen-transfer coefficient and development of conical plunging jet aerators.
Abstract: Ambient hydrolysis products in moist air and
hydrolysis kinetics in argon with humidity of RH1.5% for
polycrystalline LiH powders and sintered bulks were investigated by
X-ray diffraction, Raman spectroscopy and gravimetry. The results
showed that the hydrolysis products made up a layered structure of
LiOH•H2O/LiOH/Li2O from surface of the sample to inside. In low
humid argon atmosphere, the primary hydrolysis product was Li2O
rather than LiOH. The hydrolysis kinetic curves of LiH bulks present a
paralinear shape, which could be explained by the “Layer Diffusion
Control" model. While a three-stage hydrolysis kinetic profile was
observed for LiH powders under the same experimental conditions.
The first two sections were similar to that of the bulk samples, and the
third section also presents a linear reaction kinetics but with a smaller
reaction rate compared to the second section because of a larger
exothermic effect for the hydrolysis reaction of LiH powder.
Abstract: Text categorization - the assignment of natural language documents to one or more predefined categories based on their semantic content - is an important component in many information organization and management tasks. Performance of neural networks learning is known to be sensitive to the initial weights and architecture. This paper discusses the use multilayer neural network initialization with decision tree classifier for improving text categorization accuracy. An adaptation of the algorithm is proposed in which a decision tree from root node until a final leave is used for initialization of multilayer neural network. The experimental evaluation demonstrates this approach provides better classification accuracy with Reuters-21578 corpus, one of the standard benchmarks for text categorization tasks. We present results comparing the accuracy of this approach with multilayer neural network initialized with traditional random method and decision tree classifiers.
Abstract: Recent scientific investigations indicate that
multimodal biometrics overcome the technical limitations of
unimodal biometrics, making them ideally suited for everyday life
applications that require a reliable authentication system. However,
for a successful adoption of multimodal biometrics, such systems
would require large heterogeneous datasets with complex multimodal
fusion and privacy schemes spanning various distributed
environments. From experimental investigations of current
multimodal systems, this paper reports the various issues related to
speed, error-recovery and privacy that impede the diffusion of such
systems in real-life. This calls for a robust mechanism that caters to
the desired real-time performance, robust fusion schemes,
interoperability and adaptable privacy policies.
The main objective of this paper is to present a framework that
addresses the abovementioned issues by leveraging on the
heterogeneous resource sharing capacities of Grid services and the
efficient machine learning capabilities of artificial neural networks
(ANN). Hence, this paper proposes a Grid-based neural network
framework for adopting multimodal biometrics with the view of
overcoming the barriers of performance, privacy and risk issues that
are associated with shared heterogeneous multimodal data centres.
The framework combines the concept of Grid services for reliable
brokering and privacy policy management of shared biometric
resources along with a momentum back propagation ANN (MBPANN)
model of machine learning for efficient multimodal fusion and
authentication schemes. Real-life applications would be able to adopt
the proposed framework to cater to the varying business requirements
and user privacies for a successful diffusion of multimodal
biometrics in various day-to-day transactions.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and cvazistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine 1st stage nozzle blade
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: Investigation of sandy clay behavior is important since
urban development demands mean that sandy clay areas are
increasingly encountered, especially for transportation
infrastructures. This paper presents the results of the finite element
analysis of the direct shear test (under three vertical loading 44, 96
and 192 kPa) and discusses the effects of different parameters such as
cohesion, friction angle and Young's modulus on the shear strength of
sandy clay. The numerical model was calibrated against the
experimental results of large-scale direct shear tests. The results have
shown that the shear strength was increased with increase in friction
angle and cohesion. However, the shear strength was not influenced
by raising the friction angle at normal stress of 44 kPa. Also, the
effect of different young's modulus factors on stress-strain curve was
investigated.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: A sophisticated simulator provides a cost-effective measure to carry out preliminary mission testing and diagnostic while reducing potential failures for real life at sea trials. The presented simulation framework covers three key areas: AUV modeling, sensor modeling, and environment modeling. AUV modeling mainly covers the area of AUV dynamics. Sensor modeling deals with physics and mathematical models that govern each sensor installed onto the AUV. Environment model incorporates the hydrostatic, hydrodynamics, and ocean currents that will affect the AUV in a real-time mission. Based on this designed simulation framework, custom scenarios provided by the user can be modeled and its corresponding behaviors can be observed. This paper focuses on the accuracy of the simulated data from AUV model and environmental model derived from a developed AUV test-bed which was jointly upgraded by DSTO and the University of Adelaide. The main contribution of this paper is to experimentally verify the accuracy of the proposed simulation framework.
Abstract: Two completely different approaches for a Gigabit
Ethernet compliant stream transmission over 50m of 1mm PMMA SI-POF have been experimentally demonstrated and are compared in this paper. The first solution is based on a commercial RC-LED
transmission and a careful optimization of the physical layer architecture, realized during the POF-PLUS EU Project. The second solution exploits the performance of an edge-emitting laser at the
transmitter side in order to avoid any sort of electrical equalization at the receiver side.
Abstract: In this study, to accurately predict cavitation of a
centrifugal pump, numerical analysis was compared with experimental
results modeled on a small industrial centrifugal pump. In this study,
numerical analysis was compared with experimental results modeled
on a small industrial centrifugal pump for reliable prediction on
cavitation of a centrifugal pump. To improve validity of the numerical
analysis, transient analysis was conducted on the calculated domain of
full-type geometry, such as an experimental apparatus. The numerical
analysis from the results was considered to be a reliable prediction of
cavitaion.
Abstract: Glazing is a process used to reduce undesirable drying or dehydration of fish during frozen or cold storage. To evaluate the effect of the time/ temperature binomial of the cryogenic frozen tunnel in the amount of glazing watera Central Composite Rotatable Design was used, with application of the Response Surface Methodology. The results reveal that the time/ temperature obtained for pink cusk-eel in experimental conditions for glazing water are similar to the industrial process, but for red fish and merluza the industrial process needs some adjustments. Control charts were established and implementedto control the amount of glazing water on sardine and merluza. They show that the freezing process was statistically controlled but there were some tendencies that must be analyzed, since the trend of sample mean values approached either of the limits, mainly in merluza. Thus, appropriate actions must be taken, in order to improve the process.
Abstract: The aim of this study was to investigate whether
magnetite nanoparticles affect the viability of Bradyrhizobium
japanicum cells residing on the surface of soybean seeds during
desiccation. Different concentrations of nanoparticles suspended in
liquid medium, mixed with and adhering to Bradyrhizobium
japanicum, were investigated at two temperatures, using both
soybean seeds and glass beads as surrogates. Statistical design was a
complete randomized block (CRB) in a factorial 6×2×2×6
experimental arrangement with four replications. The most important
variable was the viability of Bradyrhizobium on the surface of the
seeds. The nanoparticles increased Bradyrhizobium viability and
inoculated seeds stored at low temperature had greater viability when
nanoparticles had been added. At the optimum nanoparticle
concentration, 50% bacterium viability on the seeds was retained
after 5 days at 4ºC. Possible explanations for the observed effects are
proposed.
Abstract: The combustion chamber dimensions have important
effects on pollutant emission in furnaces as a direct result of
temperature distribution and maximum temperature value. In this
paper the pollutant emission and the temperature distribution in two
cylindrical furnaces with different dimensions (with similar length to
diameter ratio) in similar condition have been investigated
experimentally. The furnace fuel is gas oil that is used with three
different flow rates. The results show that in these two cases the
temperature increases to its maximum value quickly, and then
decreases slowly. The results also show that increase in fuel flow rate
cause to increase in NOx emission in each case, but this increase is
greater in small furnace. With increase in fuel flow rate, CO emission
decreases firstly, and then it increases. Combustion efficiency
reduces with increase in fuel flow rate but the rate of reduction in
small furnace is greater than large furnace. The results of axial
temperature distribution have been compared with those have been
obtained numerically and experimentally by Moghiman.
Abstract: Some theoretical and experimental aspects related to
the conceptual analyses concerning the direct correspondence
identification between the shape, area and orientation of plantar
pressure and obtaining adequate corrective insoles by rapid
prototyping are presented in this paper. In the first part of the paper
there is the theoretical-correlative concept, which is the fundament of
correspondence deduction between plantar surface characteristics and
respectively corrective insoles. In the second part of the paper the
experimental equipment used to analyze and perform the
correspondence stages and then the integral ones between the
analyzed foot shapes and the ones with corrective insoles is
presented. In the final parte the results used to adapt the insoles
obtained by rapid prototyping but also some specific aspects and
conclusions of the conceptual analysis of direct and rapid
correspondence are shown.
Abstract: The small interfering RNA (siRNA) alters the
regulatory role of mRNA during gene expression by translational
inhibition. Recent studies show that upregulation of mRNA because
serious diseases like cancer. So designing effective siRNA with good
knockdown effects plays an important role in gene silencing. Various
siRNA design tools had been developed earlier. In this work, we are
trying to analyze the existing good scoring second generation siRNA
predicting tools and to optimize the efficiency of siRNA prediction
by designing a computational model using Artificial Neural Network
and whole stacking energy (%G), which may help in gene silencing
and drug design in cancer therapy. Our model is trained and tested
against a large data set of siRNA sequences. Validation of our results
is done by finding correlation coefficient of experimental versus
observed inhibition efficacy of siRNA. We achieved a correlation
coefficient of 0.727 in our previous computational model and we
could improve the correlation coefficient up to 0.753 when the
threshold of whole tacking energy is greater than or equal to -32.5
kcal/mol.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: This paper presents an analysis of the localization accuracy of indoor positioning systems using Cramer-s rule via IEEE 802.15.4 wireless sensor networks. The objective is to study the impact of the methods used to convert the received signal strength into the distance that is used to compute the object location in the wireless indoor positioning system. Various methods were tested and the localization accuracy was analyzed. The experimental results show that the method based on the empirical data measured in the non line-of-sight (NLOS) environment yield the highest localization accuracy; with the minimum error distance less than 3 m.
Abstract: The Navier–Stokes equations for unsteady, incompressible, viscous fluids in the axisymmetric coordinate system are solved using a control volume method. The volume-of-fluid (VOF) technique is used to track the free-surface of the liquid. Model predictions are in good agreement with experimental measurements. It is found that the dynamic processes after impact are sensitive to the initial droplet velocity and the liquid pool depth. The time evolution of the crown height and diameter are obtained by numerical simulation. The critical We number for splashing (Wecr) is studied for Oh (Ohnesorge) numbers in the range of 0.01~0.1; the results compares well with those of the experiments.
Abstract: Information sharing and gathering are important in the rapid advancement era of technology. The existence of WWW has caused rapid growth of information explosion. Readers are overloaded with too many lengthy text documents in which they are more interested in shorter versions. Oil and gas industry could not escape from this predicament. In this paper, we develop an Automated Text Summarization System known as AutoTextSumm to extract the salient points of oil and gas drilling articles by incorporating statistical approach, keywords identification, synonym words and sentence-s position. In this study, we have conducted interviews with Petroleum Engineering experts and English Language experts to identify the list of most commonly used keywords in the oil and gas drilling domain. The system performance of AutoTextSumm is evaluated using the formulae of precision, recall and F-score. Based on the experimental results, AutoTextSumm has produced satisfactory performance with F-score of 0.81.