Abstract: This research adapts experimental design to investigate
the effect of conditioning or not and pre-exposure or not on brand
attitude, so it is a 2×2=4 factorial design. The results show that the
brand attitude of conditioning group is significantly higher than that of
unconditioning group. The brand attitude with pre-exposure is
significantly higher than that without pre-exposure. Conditioning or
not and pre-exposure or not have significant interaction. No matter the
celebrity is pre-exposure or not, the brand attitude is higher under
conditioning process.
Abstract: A thin layer on the component surface can be found
with high tensile residual stresses, due to turning operations, which
can dangerously affect the fatigue performance of the component. In
this paper an analytical approach is presented to reconstruct the
residual stress field from a limited incomplete set of measurements.
Airy stress function is used as the primary unknown to directly solve
the equilibrium equations and satisfying the boundary conditions. In
this new method there exists the flexibility to impose the physical
conditions that govern the behavior of residual stress to achieve a
meaningful complete stress field. The analysis is also coupled to a
least squares approximation and a regularization method to provide
stability of the inverse problem. The power of this new method is
then demonstrated by analyzing some experimental measurements
and achieving a good agreement between the model prediction and
the results obtained from residual stress measurement.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: This paper is concerned with the application of the vision control algorithm for robot's point placement task in discontinuous trajectory caused by obstacle. The presented vision control algorithm consists of four models, which are the robot kinematic model, vision system model, parameters estimation model, and robot joint angle estimation model.When the robot moves toward a target along discontinuous trajectory, several types of obstacles appear in two obstacle regions. Then, this study is to investigate how these changes will affect the presented vision control algorithm.Thus, the practicality of the vision control algorithm is demonstrated experimentally by performing the robot's point placement task in discontinuous trajectory by obstacle.
Abstract: Automotive engine air-ratio plays an important role of
emissions and fuel consumption reduction while maintains
satisfactory engine power among all of the engine control variables. In
order to effectively control the air-ratio, this paper presents a model
predictive fuzzy control algorithm based on online least-squares
support vector machines prediction model and fuzzy logic optimizer.
The proposed control algorithm was also implemented on a real car for
testing and the results are highly satisfactory. Experimental results
show that the proposed control algorithm can regulate the engine
air-ratio to the stoichiometric value, 1.0, under external disturbance
with less than 5% tolerance.
Abstract: How to efficiently assign system resource to route the
Client demand by Gateway servers is a tricky predicament. In this
paper, we tender an enhanced proposal for autonomous recital of
Gateway servers under highly vibrant traffic loads. We devise a
methodology to calculate Queue Length and Waiting Time utilizing
Gateway Server information to reduce response time variance in
presence of bursty traffic.
The most widespread contemplation is performance, because
Gateway Servers must offer cost-effective and high-availability
services in the elongated period, thus they have to be scaled to meet
the expected load. Performance measurements can be the base for
performance modeling and prediction. With the help of performance
models, the performance metrics (like buffer estimation, waiting
time) can be determined at the development process.
This paper describes the possible queue models those can be
applied in the estimation of queue length to estimate the final value
of the memory size. Both simulation and experimental studies using
synthesized workloads and analysis of real-world Gateway Servers
demonstrate the effectiveness of the proposed system.
Abstract: Most file systems overwrite modified file data and
metadata in their original locations, while the Log-structured File
System (LFS) dynamically relocates them to other locations. We
design and implement the Evergreen file system that can select
between overwriting or relocation for each block of a file or metadata.
Therefore, the Evergreen file system can achieve superior write
performance by sequentializing write requests (similar to LFS-style
relocation) when space utilization is low and overwriting when
utilization is high. Another challenging issue is identifying
performance benefits of LFS-style relocation over overwriting on a
newly introduced SSD (Solid State Drive) which has only
Flash-memory chips and control circuits without mechanical parts.
Our experimental results measured on a SSD show that relocation
outperforms overwriting when space utilization is below 80% and vice
versa.
Abstract: The objective of this research is parameters optimized
of the stair shape workpiece which is cut by CNC Wire-Cut EDM
(WEDW). The experiment material is SKD-11 steel of stair-shaped
with variable height workpiece 10, 20, 30 and 40 mm. with the same
10 mm. thickness are cut by Sodick's CNC Wire-Cut EDM model
AD325L.
The experiments are designed by 3k full factorial experimental
design at 3 level 2 factors and 9 experiments with 2 replicate. The
selected two factor are servo voltage (SV) and servo feed rate (SF)
and the response is cutting thickness error. The experiment is divided
in two experiments. The first experiment determines the significant
effective factor at confidential interval 95%. The SV factor is the
significant effective factor from first result. In order to result smallest
cutting thickness error of workpieces is 17 micron with the SV value
is 46 volt. Also show that the lower SV value, the smaller different
thickness error of workpiece. Then the second experiment is done to
reduce different cutting thickness error of workpiece as small as
possible by lower SV. The second experiment result show the
significant effective factor at confidential interval 95% is the SV
factor and the smallest cutting thickness error of workpieces reduce
to 11 micron with the experiment SV value is 36 volt.
Abstract: A mathematical model for the hydrodynamics of a
surface water treatment pilot plant was developed and validated by
the determination of the residence time distribution (RTD) for the
main equipments of the unit. The well known models of ideal/real
mixing, ideal displacement (plug flow) and (one-dimensional axial)
dispersion model were combined in order to identify the structure
that gives the best fitting of the experimental data for each equipment
of the pilot plant. RTD experimental results have shown that pilot
plant hydrodynamics can be quite well approximated by a
combination of simple mathematical models, structure which is
suitable for engineering applications. Validated hydrodynamic
models will be further used in the evaluation and selection of the
most suitable coagulation-flocculation reagents, optimum operating
conditions (injection point, reaction times, etc.), in order to improve
the quality of the drinking water.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: In the context of channel coding, the Generalized Belief Propagation (GBP) is an iterative algorithm used to recover the transmission bits sent through a noisy channel. To ensure a reliable transmission, we apply a map on the bits, that is called a code. This code induces artificial correlations between the bits to send, and it can be modeled by a graph whose nodes are the bits and the edges are the correlations. This graph, called Tanner graph, is used for most of the decoding algorithms like Belief Propagation or Gallager-B. The GBP is based on a non unic transformation of the Tanner graph into a so called region-graph. A clear advantage of the GBP over the other algorithms is the freedom in the construction of this graph. In this article, we explain a particular construction for specific graph topologies that involves relevant performance of the GBP. Moreover, we investigate the behavior of the GBP considered as a dynamic system in order to understand the way it evolves in terms of the time and in terms of the noise power of the channel. To this end we make use of classical measures and we introduce a new measure called the hyperspheres method that enables to know the size of the attractors.
Abstract: Response surface methodology was used for
quantitative investigation of water and solids transfer during osmotic
dehydration of beetroot in aqueous solution of salt. Effects of
temperature (25 – 45oC), processing time (30–150 min), salt
concentration (5–25%, w/w) and solution to sample ratio (5:1 – 25:1)
on osmotic dehydration of beetroot were estimated. Quadratic
regression equations describing the effects of these factors on the
water loss and solids gain were developed. It was found that effects
of temperature and salt concentrations were more significant on the
water loss than the effects of processing time and solution to sample
ratio. As for solids gain processing time and salt concentration were
the most significant factors. The osmotic dehydration process was
optimized for water loss, solute gain, and weight reduction. The
optimum conditions were found to be: temperature – 35oC,
processing time – 90 min, salt concentration – 14.31% and solution
to sample ratio 8.5:1. At these optimum values, water loss, solid gain
and weight reduction were found to be 30.86 (g/100 g initial sample),
9.43 (g/100 g initial sample) and 21.43 (g/100 g initial sample)
respectively.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: This paper will present the initial findings of a
research into distributed computer rendering. The goal of the
research is to create a distributed computer system capable of
rendering a 3D model into an MPEG-4 stream. This paper outlines
the initial design, software architecture and hardware setup for the
system.
Distributed computing means designing and implementing
programs that run on two or more interconnected computing systems.
Distributed computing is often used to speed up the rendering of
graphical imaging. Distributed computing systems are used to
generate images for movies, games and simulations.
A topic of interest is the application of distributed computing to
the MPEG-4 standard. During the course of the research, a
distributed system will be created that can render a 3D model into an
MPEG-4 stream. It is expected that applying distributed computing
principals will speed up rendering, thus improving the usefulness and
efficiency of the MPEG-4 standard
Abstract: This paper presents a highly efficient algorithm for detecting and tracking humans and objects in video surveillance sequences. Mean shift clustering is applied on backgrounddifferenced image sequences. For efficiency, all calculations are performed on integral images. Novel corresponding exponential integral kernels are introduced to allow the application of nonuniform kernels for clustering, which dramatically increases robustness without giving up the efficiency of the integral data structures. Experimental results demonstrating the power of this approach are presented.
Abstract: Minimization methods for training feed-forward networks with Backpropagation are compared. Feedforward network training is a special case of functional minimization, where no explicit model of the data is assumed. Therefore due to the high dimensionality of the data, linearization of the training problem through use of orthogonal basis functions is not desirable. The focus is functional minimization on any basis. A number of methods based on local gradient and Hessian matrices are discussed. Modifications of many methods of first and second order training methods are considered. Using share rates data, experimentally it is proved that Conjugate gradient and Quasi Newton?s methods outperformed the Gradient Descent methods. In case of the Levenberg-Marquardt algorithm is of special interest in financial forecasting.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: This paper propose a new circuit design which
monitor total leakage current during standby mode and generates the
optimal reverse body bias voltage, by using the adaptive body bias
(ABB) technique to compensate die-to-die parameter variations.
Design details of power monitor are examined using simulation
framework in 65nm and 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 10 μW for 32nm technology and
about 12 μW for 65nm technology at the same power supply voltage
as the core power supply. Moreover the results show that our
proposed circuit design is not far sensitive to the temperature
variations and also process variations. Besides, uses the simple
blocks which offer good sensitivity, high speed, the continuously
feedback loop.