Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: The aims of this paper are to study the efficacy of
chitosan nanoparticles in stimulating specific antibody against
A/H1N1 influenza antigen in mice. Chitosan nanoparticles (CSN)
were characterized by TEM. The results showed that the average size
of CSN was from 80nm to 106nm. The efficacy of A/H1N1 influenza
vaccine loaded on the surface of CSN showed that loading efficiency
of A/H1N1 influenza antigen on CSN was from 93.75 to 100%. Safe
property of the vaccine were tested. In 10 days post vaccination,
group of CSN 30 kDa and 300 kDa loaded A/H1N1 influenza antigen
were the rate of immune response on mice to be 100% (9/9) higher
than Al(OH)3 and other adjuvant. 100% mice in the experiment of all
groups had immune response in 20 days post vaccination. The results
also showed that HI titer of the group using CSN 300 kDa as an
adjuvant increased significantly up to 3971 HIU, over three-fold
higher than the Al(OH)3 adjuvant, chitosan (CS), and one hundredfold
than the A/H1N1 antigen only. Stability of the vaccine
formulation was investigated.
Abstract: We estimate snow velocity and snow drift density on hilly terrain under the assumption that the drifting snow mass can be represented using a micro-continuum approach (i.e. using a nonclassical mechanics approach assuming a class of fluids for which basic equations of mass, momentum and energy have been derived). In our model, the theory of coupled stress fluids proposed by Stokes [1] has been employed for the computation of flow parameters. Analyses of bulk drift velocity, drift density, drift transport and mass transport of snow particles have been carried out and computations made, considering various parametric effects. Results are compared with those of classical mechanics (logarithmic wind profile). The results indicate that particle size affects the flow characteristics significantly.
Abstract: At present, web Service is the first choice to reuse the
legacy system for the implementation of SOA. According to the status
of the implementation of SOA and the status of the legacy systems, we propose four encapsulating strategies. Base on the strategies, we
proposal the service-oriented encapsulating framework, the legacy system can be encapsulated by the service-oriented encapsulating
layer in three aspects, communication protocols, data and program.
The reuse rate of the legacy systems can be increased by using this framework
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: In distributed resource allocation a set of agents must assign their resources to a set of tasks. This problem arises in many real-world domains such as distributed sensor networks, disaster rescue, hospital scheduling and others. Despite the variety of approaches proposed for distributed resource allocation, a systematic formalization of the problem, explaining the different sources of difficulties, and a formal explanation of the strengths and limitations of key approaches is missing. We take a step towards this goal by using a formalization of distributed resource allocation that represents both dynamic and distributed aspects of the problem. In this paper we present a new idea for target tracking in sensor networks and compare it with previous approaches. The central contribution of the paper is a generalized mapping from distributed resource allocation to DDCSP. This mapping is proven to correctly perform resource allocation problems of specific difficulty. This theoretical result is verified in practice by a simulation on a realworld distributed sensor network.
Abstract: This research investigates the factors that influence moral judgments when dealing with ethical dilemmas in the organizational context. It also investigates the antecedents of individual ethical ideology (idealism and relativism). A mixed method study, which combines qualitative (field study) and quantitative (survey) approaches, was used in this study. An initial model was developed first, which was then fine-tuned based on field studies. Data were collected from managers in Malaysian large organizations. The results of this study reveal that in-group collectivism culture, power distance culture, parental values, and religiosity were significant as antecedents of ethical ideology. However, direct effects of these variables on moral judgment were not significant. Furthermore, the results of this study confirm the significant effects of ethical ideology on moral judgment. This study provides valuable insight into evaluating the validity of existing theory as proposed in the literature and offers significant practical implications.
Abstract: Field mapping activity for an active volcano mainly in
the Torrid Zone is usually hampered by several problems such as steep
terrain and bad atmosphere conditions. In this paper we present a
simple solution for such problem by a combination Synthetic Aperture
Radar (SAR) and geostatistical methods. By this combination, we
could reduce the speckle effect from the SAR data and then estimate
roughness distribution of the pyroclastic flow deposits. The main
purpose of this study is to detect spatial distribution of new pyroclastic
flow deposits termed as P-zone accurately using the β°data from two
RADARSAT-1 SAR level-0 data. Single scene of Hyperion data and
field observation were used for cross-validation of the SAR results.
Mt. Merapi in central Java, Indonesia, was chosen as a study site and
the eruptions in May-June 2006 were examined. The P-zones were
found in the western and southern flanks. The area size and the longest
flow distance were calculated as 2.3 km2 and 6.8 km, respectively. The
grain size variation of the P-zone was mapped in detail from fine to
coarse deposits regarding the C-band wavelength of 5.6 cm.
Abstract: Phase locked loops (PLL) and delay locked loops (DLL) play an important role in establishing coherent references (phase of carrier and symbol timing) in digital communication systems. Fully digital receiver including digital carrier synchronizer and symbol timing synchronizer fulfils the conditions for universal multi-mode communication receiver with option of symbol rate setting over several digit places and long-term stability of requirement parameters. Afterwards it is necessary to realize PLL and DLL in synchronizer in digital form and to approach to these subsystems as a discrete representation of analog template. Analysis of discrete phase locked loop (DPLL) or discrete delay locked loop (DDLL) and technique to determine their characteristics based on analog (continuous-time) template is performed in this posed paper. There are derived transmission response and error function for 1st order discrete locked loop and resulting equations and graphical representations for 2nd order one. It is shown that the spectrum translation due to sampling takes effect at frequency characteristics computing for specific values of loop parameters.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: Coagulation of water involves the use of coagulating
agents to bring the suspended matter in the raw water together for
settling and the filtration stage. Present study is aimed to examine the
effects of aluminum sulfate as coagulant in conjunction with Moringa
Oleifera Coagulant Protein as coagulant aid on turbidity, hardness,
and bacteria in turbid water. A conventional jar test apparatus was
employed for the tests. The best removal was observed at a pH of 7
to 7.5 for all turbidities. Turbidity removal efficiency was resulted
between % 80 to % 99 by Moringa Oleifera Coagulant Protein as
coagulant aid. Dosage of coagulant and coagulant aid decreased with
increasing turbidity. In addition, Moringa Oleifera Coagulant Protein
significantly has reduced the required dosage of primary coagulant.
Residual Al+3 in treated water were less than 0.2 mg/l and meets the
environmental protection agency guidelines. The results showed that
turbidity reduction of % 85.9- % 98 paralleled by a primary
Escherichia coli reduction of 1-3 log units (99.2 – 99.97%) was
obtained within the first 1 to 2 h of treatment. In conclusions,
Moringa Oleifera Coagulant Protein as coagulant aid can be used for
drinking water treatment without the risk of organic or nutrient
release. We demonstrated that optimal design method is an efficient
approach for optimization of coagulation-flocculation process and
appropriate for raw water treatment.
Abstract: The importance of nurturing, accumulating, and efficiently deploying knowledge resources through formal structures and organisational mechanisms is well understood. Recent trends in knowledge management (KM) highlight that the effective creation and transfer of knowledge can also rely upon extra-organisational channels, such as, informal networks. The perception exists that the role of informal networks in knowledge creation and performance has been underestimated in the organisational context. Literature indicates that many managers fail to comprehend and successfully exploit the potential role of informal networks to create value for their organisations. This paper investigates: 1) whether managers share work-specific knowledge with informal contacts within and outside organisational boundaries; and 2) what do they think is the importance of this knowledge collaboration in their learning and work outcomes.
Abstract: Located within the tropical belt region, there are
certain rules which should implemented in creating a passive
sustainable housing design in Malaysia. Traditional Malay house
possess a strong character with certain special spaces to create a
sustainable house which suit to the tropical climate in Malaysia. One
of the special space known as verandah or serambi gantung, create
various advantages in solving various issues. However, this special
space is not extremely being applied currently which produce major
issues in term of social and environmental aspects. Hence, this
phenomena create a negative impact to the occupant while Malaysia
already has a best housing design previously. Therefore, this paper
aims to explore both of the main issues mentioned above and reveal
the advantages of implementing verandah into passive sustainable
housing design in Malaysia. A systematic literature review is the
main methodology in this research to identify the various advantages
about verandah.. The study reveals that verandah is the best solution
in term of social and environmental issues and should be
implemented in current housing design in Malaysia.
Abstract: The restoration of extinct ponds is considered as one
of ways to gain new retention capacities for water which is getting
much more important issue with respect to expected impacts of a
climate change. However, there are also other pressures on the
landscape which must be all taken into consideration when making a
decision on the possible restoration of extinct ponds. The research
presented here focuses besides others on the restoration of former
ponds which could be important for both the flood protection and
drought impacts prevention. The first step of the methodology
development for the assessment of such areas is the assessment of
their present state. In this paper, the results of land use types
assessment for 22 localities are presented. These results confirm the
assumption that the most present land use type in such areas is the
permanent grassland. However, the spectra of land use types present
in extinct pond areas is very diverse and include besides others also
airport areas and industry.
Abstract: PCMs have always been viewed as a suitable
candidate for off peak thermal storage, particularly for refrigeration
systems, due to the high latent energy densities of these materials.
However, due to the need to have them encapsulated within a
container this density is reduced. Furthermore, PCMs have a low
thermal conductivity which reduces the useful amount of energy
which can be stored. To consider these factors, the true energy
storage density of a PCM system was proposed and optimised for
PCMs encapsulated in slabs. Using a validated numerical model of
the system, a parametric study was undertaken to investigate the
impact of the slab thickness, gap between slabs and the mass flow
rate. The study showed that, when optimised, a PCM system can
deliver a true energy storage density between 53% and 83% of the
latent energy density of the PCM.
Abstract: The mechanical properties including flexural and
tensile of neat vinyl ester and polymer based on layered silicate
nanocomposite materials are discussed. The addition of layered
silicate into the polymer matrix increased the tensile and flexural
modulus up to 1 wt.% clay loading. The incorporation of more clay
resulted in decreasing the mechanical properties which was traced to
the existence of aggregation layers. Likewise, up to 1 wt.% clay
loading, the thermal behaviour showed significant improvements and
at higher clay loading the thermal pattern was reduced. The
aggregation layers imparted a negative impact on the overall
mechanical and thermal properties. Wide Angle X-ray Diffraction,
Scanning Electron Microscopy and Transmission Electron
Microscopy were utilised in order to characterise the interlamellar
structure of nanocomposites.
Abstract: The traditional method for essential oil extraction from agarwood (Aquilaria Crassna) is to soak it in water and follow with hydrodistillation. The effect of various agarwood pretreatments: ethanol, acid, alkaline, enzymes, and ultrasound, and the effect of subcritical water extraction(SWE) was studied to compare with the traditional method. The major compositions of agarwood oil from hydrodistillation were aroma compounds as follow: aristol-9-en-8- one (21.53%), selina-3, 7(11)-diene (12.96%), τ-himachalene (9.28%), β-guaiene (5.79%), hexadecanoic acid (4.90%) and guaia- 3,9-diene (4.21%). Whereas agarwood oil from pretreatments with ethanol and ultrasound, and SWE got fatty acid compounds. Extraction of agarwood oil using these pretreatments could improve the agarwood oil yields up to 2 times that of the traditional method. The components of the pretreated sample with diluted acid (H2SO4) at pH 4 gave quite similar results as the traditional method. Therefore, the enhancement of essential oil from agarwood depends on requirement of type of extracted oil that involved extraction methods.
Abstract: Image data holds a large amount of different context
information. However, as of today, these resources remain largely
untouched. It is thus the aim of this paper to present a basic technical
framework which allows for a quick and easy exploitation of context
information from image data especially by non-expert users.
Furthermore, the proposed framework is discussed in detail
concerning important social and ethical issues which demand special
requirements in system design. Finally, a first sensor prototype is
presented which meets the identified requirements. Additionally,
necessary implications for the software and hardware design of the
system are discussed, rendering a sensor system which could be
regarded as a good, acceptable and justifiable technical and thereby
enabling the extraction of context information from image data.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of quartz, mullite, and unburned
carbon. In this study, the effect of unburned carbon on CFA toward
its adsorption capacity was investigated. CFA with various carbon
content was obtained by refluxing it with sulfuric acid having various
concentration at various temperature and reflux time, by heating at
400-800°C, and by sieving into 100-mesh in particle size. To
evaluate the effect of unburned carbon on CFA toward its adsorption
capacity, adsorption of methyl violet solution with treated CFA was
carried out. The research shows that unburned carbon leads to
adsorption capacity decrease. The highest adsorption capacity of
treated CFA was found 5.73 x 10-4mol.g-1.
Abstract: In many industries, control charts is one of the most
frequently used tools for quality management. Hotelling-s T2 is used
widely in multivariate control chart. However, it has little defect when
detecting small or medium process shifts. The use of supplementary
sensitizing rules can improve the performance of detection. This study
applied sensitizing rules for Hotelling-s T2 control chart to improve the
performance of detection. Support vector machines (SVM) classifier
to identify the characteristic or group of characteristics that are
responsible for the signal and to classify the magnitude of the mean
shifts. The experimental results demonstrate that the support vector
machines (SVM) classifier can effectively identify the characteristic
or group of characteristics that caused the process mean shifts and the
magnitude of the shifts.