Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: In this paper, a novel deinterlacing algorithm is
proposed. The proposed algorithm approximates the distribution of the
luminance into a polynomial function. Instead of using one
polynomial function for all pixels, different polynomial functions are
used for the uniform, texture, and directional edge regions. The
function coefficients for each region are computed by matrix
multiplications. Experimental results demonstrate that the proposed
method performs better than the conventional algorithms.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: Wavelet transforms are multiresolution
decompositions that can be used to analyze signals and images.
Image compression is one of major applications of wavelet
transforms in image processing. It is considered as one of the most
powerful methods that provides a high compression ratio. However,
its implementation is very time-consuming. At the other hand,
parallel computing technologies are an efficient method for image
compression using wavelets. In this paper, we propose a parallel
wavelet compression algorithm based on quadtrees. We implement
the algorithm using MatlabMPI (a parallel, message passing version
of Matlab), and compute its isoefficiency function, and show that it is
scalable. Our experimental results confirm the efficiency of the
algorithm also.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: The brain MR imaging-based clinical research and analysis system were specifically built and the development for a large-scale data was targeted. We used the general clinical data available for building large-scale data. Registration period for the selection of the lesion ROI and the region growing algorithm was used and the Mesh-warp algorithm for matching was implemented. The accuracy of the matching errors was modified individually. Also, the large ROI research data can accumulate by our developed compression method. In this way, the correctly decision criteria to the research result was suggested. The experimental groups were age, sex, MR type, patient ID and smoking which can easily be queries. The result data was visualized of the overlapped images by a color table. Its data was calculated by the statistical package. The evaluation for the utilization of this system in the chronic ischemic damage in the area has done from patients with the acute cerebral infarction. This is the cause of neurologic disability index location in the center portion of the lateral ventricle facing. The corona radiate was found in the position. Finally, the system reliability was measured both inter-user and intra-user registering correlation.
Abstract: The evolutionary design of electronic circuits, or
evolvable hardware, is a discipline that allows the user to
automatically obtain the desired circuit design. The circuit
configuration is under the control of evolutionary algorithms. Several
researchers have used evolvable hardware to design electrical
circuits. Every time that one particular algorithm is selected to carry
out the evolution, it is necessary that all its parameters, such as
mutation rate, population size, selection mechanisms etc. are tuned in
order to achieve the best results during the evolution process. This
paper investigates the abilities of evolution strategy to evolve digital
logic circuits based on programmable logic array structures when
different mutation rates are used. Several mutation rates (fixed and
variable) are analyzed and compared with each other to outline the
most appropriate choice to be used during the evolution of
combinational logic circuits. The experimental results outlined in this
paper are important as they could be used by every researcher who
might need to use the evolutionary algorithm to design digital logic
circuits.
Abstract: Various intelligences and inspirations have been
adopted into the iterative searching process called as meta-heuristics.
They intelligently perform the exploration and exploitation in the
solution domain space aiming to efficiently seek near optimal
solutions. In this work, the bee algorithm, inspired by the natural
foraging behaviour of honey bees, was adapted to find the near
optimal solutions of the transportation management system, dynamic
multi-zone dispatching. This problem prepares for an uncertainty and
changing customers- demand. In striving to remain competitive,
transportation system should therefore be flexible in order to cope
with the changes of customers- demand in terms of in-bound and outbound
goods and technological innovations. To remain higher service
level but lower cost management via the minimal imbalance scenario,
the rearrangement penalty of the area, in each zone, including time
periods are also included. However, the performance of the algorithm
depends on the appropriate parameters- setting and need to be
determined and analysed before its implementation. BEE parameters
are determined through the linear constrained response surface
optimisation or LCRSOM and weighted centroid modified simplex
methods or WCMSM. Experimental results were analysed in terms
of best solutions found so far, mean and standard deviation on the
imbalance values including the convergence of the solutions
obtained. It was found that the results obtained from the LCRSOM
were better than those using the WCMSM. However, the average
execution time of experimental run using the LCRSOM was longer
than those using the WCMSM. Finally a recommendation of proper
level settings of BEE parameters for some selected problem sizes is
given as a guideline for future applications.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: The neurogenic potential of many herbal extracts used
in Indian medicine is hitherto unknown. Extracts derived from
Clitoria ternatea Linn have been used in Indian Ayurvedic system of
medicine as an ingredient of “Medhya rasayana", consumed for
improving memory and longevity in humans and also in treatment of
various neurological disorders. Our earlier experimental studies with
oral intubation of Clitoria ternatea aqueous root extract (CTR) had
shown significant enhancement of learning and memory in postnatal
and young adult Wistar rats. The present study was designed to
elucidate the in vitro effects of 200ng/ml of CTR on proliferation,
differentiation and growth of anterior subventricular zone neural
stem cells (aSVZ NSC-s) derived from prenatal and postnatal rat
pups. Results show significant increase in proliferation and growth of
neurospheres and increase in the yield of differentiated neurons of
aSVZ neural precursor cells (aSVZNPC-s) at 7 days in vitro when
treated with 200ng/ml of CTR as compared to age matched control.
Results indicate that CTR has growth promoting neurogenic effect on
aSVZ neural stem cells and their survival similar to neurotrophic
factors like Survivin, Neuregulin 1, FGF-2, BDNF possibly the basis
for enhanced learning and memory.
Abstract: An evolutionary method whose selection and recombination
operations are based on generalization error-bounds of
support vector machine (SVM) can select a subset of potentially
informative genes for SVM classifier very efficiently [7]. In this
paper, we will use the derivative of error-bound (first-order criteria)
to select and recombine gene features in the evolutionary process,
and compare the performance of the derivative of error-bound with
the error-bound itself (zero-order) in the evolutionary process. We
also investigate several error-bounds and their derivatives to compare
the performance, and find the best criteria for gene selection
and classification. We use 7 cancer-related human gene expression
datasets to evaluate the performance of the zero-order and first-order
criteria of error-bounds. Though both criteria have the same strategy
in theoretically, experimental results demonstrate the best criterion
for microarray gene expression data.
Abstract: Documents retrieval in Information Retrieval
Systems (IRS) is generally about understanding of
information in the documents concern. The more the system
able to understand the contents of documents the more
effective will be the retrieval outcomes. But understanding of the
contents is a very complex task. Conventional IRS apply algorithms
that can only approximate the meaning of document contents through
keywords approach using vector space model. Keywords may be
unstemmed or stemmed. When keywords are stemmed and conflated
in retrieving process, we are a step forwards in applying semantic
technology in IRS. Word stemming is a process in morphological
analysis under natural language processing, before syntactic and
semantic analysis. We have developed algorithms for Malay and
Arabic and incorporated stemming in our experimental systems in
order to measure retrieval effectiveness. The results have shown that
the retrieval effectiveness has increased when stemming is used in
the systems.
Abstract: A two dimensional numerical simulation has been
performed for incompressible and compressible fluid flow through
microchannels in slip flow regime. The Navier-Stokes equations have
been solved in conjunction with Maxwell slip conditions for
modeling flow field associated with slip flow regime. The wall
roughness is simulated with triangular microelements distributed on
wall surfaces to study the effects of roughness on fluid flow. Various
Mach and Knudsen numbers are used to investigate the effects of
rarefaction as well as compressibility. It is found that rarefaction has
more significant effect on flow field in microchannels with higher
relative roughness. It is also found that compressibility has more
significant effects on Poiseuille number when relative roughness
increases. In addition, similar to incompressible models the increase
in average fRe is more significant at low Knudsen number flows but
the increase of Poiseuille number duo to relative roughness is sharper
for compressible models. The numerical results have also validated
with some available theoretical and experimental relations and good
agreements have been seen.
Abstract: Texture information plays increasingly an important
role in remotely sensed imagery classification and many pattern
recognition applications. However, the selection of relevant textural
features to improve this classification accuracy is not a straightforward
task. This work investigates the effectiveness of two Mutual
Information Feature Selector (MIFS) algorithms to select salient
textural features that contain highly discriminatory information for
multispectral imagery classification. The input candidate features are
extracted from a SPOT High Resolution Visible(HRV) image using
Wavelet Transform (WT) at levels (l = 1,2).
The experimental results show that the selected textural features
according to MIFS algorithms make the largest contribution to
improve the classification accuracy than classical approaches such
as Principal Components Analysis (PCA) and Linear Discriminant
Analysis (LDA).
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: Due to availability of powerful image processing software
and improvement of human computer knowledge, it becomes
easy to tamper images. Manipulation of digital images in different
fields like court of law and medical imaging create a serious problem
nowadays. Copy-move forgery is one of the most common types
of forgery which copies some part of the image and pastes it to
another part of the same image to cover an important scene. In
this paper, a copy-move forgery detection method proposed based
on Fourier transform to detect forgeries. Firstly, image is divided to
same size blocks and Fourier transform is performed on each block.
Similarity in the Fourier transform between different blocks provides
an indication of the copy-move operation. The experimental results
prove that the proposed method works on reasonable time and works
well for gray scale and colour images. Computational complexity
reduced by using Fourier transform in this method.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.