Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: This research aims to study the lead pollution in the air of Babylon governorate that resulted generally from vehicles exhausts in addition to industrial and human activities.Vehicles number in Babylon governorate increased significantly after year 2003 that resulted with increase in lead emissions into the air.Measurement of lead emissions was done in seven stations distributed randomly in Babylon governorate. These stations where located in Industrial (Al-Sena'ay) Quarter, 60 street (near to Babylon sewer directorate), 40 Street (near to the first intersection), Al-Hashmia city, Al-Mahaweel city, , Al- Musayab city in addition to another station in Sayd Idris village belong to Abugharaq district (Agricultural station for comparison). The measured concentrations in these stations were compared with the standard limits of Environmental Protection Agency EPA (2 μg /m3). The results of this study showed that the average of lead concentrations ,in Babylon governorate during year 2010, was (3.13 μg/m3) which was greater than standard limits (2 μg/m3). The maximum concentration of lead was (6.41 μg / m3) recorded in the Industrial (Al-Sena'ay) Quarter during April month, while the minimum concentrations was (0.36 μg / m3) recorded in the agricultural station (Abugharaq) during December month.
Abstract: A framework to estimate the state of dynamically
varying environment where data are generated from heterogeneous
sources possessing partial knowledge about the environment is presented.
This is entirely derived within Dempster-Shafer and Evidence
Filtering frameworks. The belief about the current state is expressed
as belief and plausibility functions. An addition to Single Input
Single Output Evidence Filter, Multiple Input Single Output Evidence
Filtering approach is introduced. Variety of applications such as
situational estimation of an emergency environment can be developed
within the framework successfully. Fire propagation scenario is used
to justify the proposed framework, simulation results are presented.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: Sparse representation which can represent high dimensional
data effectively has been successfully used in computer vision
and pattern recognition problems. However, it doesn-t consider the
label information of data samples. To overcome this limitation,
we develop a novel dimensionality reduction algorithm namely
dscriminatively regularized sparse subspace learning(DR-SSL) in this
paper. The proposed DR-SSL algorithm can not only make use of
the sparse representation to model the data, but also can effective
employ the label information to guide the procedure of dimensionality
reduction. In addition,the presented algorithm can effectively deal
with the out-of-sample problem.The experiments on gene-expression
data sets show that the proposed algorithm is an effective tool for
dimensionality reduction and gene-expression data classification.
Abstract: This study aims to examine the determinants of
purchase intention in C2C e-commerce. Specifically the role of
instant messaging in the C2C e-commerce contextis investigated. In
addition to instant messaging, we brought in two antecedents of
purchase intention - trust and customer satisfaction - to establish a
theoretical research model. Structural equation modeling using
LISREL was used to analyze the data.We discussed the research
findings and suggested some implications for researchers and
practitioners.
Abstract: The vast rural landscape in the southern United States
is conspicuously characterized by the hedgerow trees or groves. The
patchwork landscape of fields surrounded by high hedgerows is a
traditional and familiar feature of the American countryside.
Hedgerows are in effect linear strips of trees, groves, or woodlands,
which are often critical habitats for wildlife and important for the
visual quality of the landscape. As landscape interfaces, hedgerows
define the spaces in the landscape, give the landscape life and
meaning, and enrich ecologies and cultural heritages of the American
countryside. Although hedgerows were originally intended as fences
and to mark property and townland boundaries, they are not merely
the natural or man-made additions to the landscape--they have
gradually become “naturalized" into the landscape, deeply rooted in
the rural culture, and now formed an important component of the
southern American rural environment. However, due to the ever
expanding real estate industry and high demand for new residential
development, substantial areas of authentic hedgerow landscape in
the southern United States are being urbanized. Using Hudson Farm
as an example, this study illustrated guidelines of how hedgerows can
be integrated into town planning as green infrastructure and
landscape interface to innovate and direct sustainable land use, and
suggest ways in which such vernacular landscapes can be preserved
and integrated into new development without losing their contextual
inspiration.
Abstract: In an Orthogonal Frequency Division Multiplexing (OFDM) systems, the Peak to Average power Ratio (PAR) is high. The clipping signal scheme is a useful and simple method to reduce the PAR. However, it introduces additional noise that degrades the systems performance. We propose an oversampling scheme to deal with the received signal in order to reduce the clipping noise by using Finite Impulse Response (FIR) filter. Coefficients of filter are obtained by correlation function of the received signal and the oversampling information at receiver. The performance of the proposed technique is evaluated for frequency selective channel. Results show that the proposed scheme can mitigate the clipping noise significantly for OFDM systems and in order to maintain the system's capacity, the clipping ratio should be larger than 2.5.
Abstract: This paper aims to (1) analyze the profiles of
transgressors (detected evaders); (2) examine reason(s) that triggered a
tax audit, causes of tax evasion, audit timeframe and tax penalty
charged; and (3) to assess if tax auditors followed the guidelines as
stated in the 'Tax Audit Framework' when conducting tax audits. In
2011, the Inland Revenue Board Malaysia (IRBM) had audited and
finalized 557 company cases. With official permission, data of all the
557 cases were obtained from the IRBM. Of these, a total of 421 cases
with complete information were analyzed. About 58.1% was small and
medium corporations and from the construction industry (32.8%). The
selection for tax audit was based on risk analysis (66.8%), information
from third party (11.1%), and firm with low profitability or fluctuating
profit pattern (7.8%). The three persistent causes of tax evasion by
firms were over claimed expenses (46.8%), fraudulent reporting of
income (38.5%) and overstating purchases (10.5%). These findings
are consistent with past literature. Results showed that tax auditors
took six to 18 months to close audit cases. More than half of tax
evaders were fined 45% on additional tax raised during audit for the
first offence. The study found tax auditors did follow the guidelines in
the 'Tax Audit Framework' in audit selection, settlement and penalty
imposition.
Abstract: This paper proposes a novel stereo vision technique
for top view book scanners which provide us with dense 3d point
clouds of page surfaces. This is a precondition to dewarp bound
volumes independent of 2d information on the page. Our method is
based on algorithms, which normally require the projection of pattern
sequences with structured light. We use image sequences of the
moving stripe lighting of the top view scanner instead of an additional
light projection. Thus the stereo vision setup is simplified without
losing measurement accuracy. Furthermore we improve a surface
model dewarping method through introducing a difference vector
based on real measurements. Although our proposed method is hardly
expensive neither in calculation time nor in hardware requirements
we present good dewarping results even for difficult examples.
Abstract: The online office is one of web application. We can
easily use the online office through a web browser with internet
connected PC. The online office has the advantage of using
environment regardless of location or time. When users want to use the
online office, they access the online office server and use their content.
However, recently developed and launched online office has the
weakness of insufficient consideration. In this paper, we analyze the
security vulnerabilities of the online office. In addition, we propose
the evaluation criteria to make secure online office using Common
Criteria. This evaluation criteria can be used to establish trust between
the online office server and the user. The online office market will be
more active than before.
Abstract: The struggle between modern and postmodern
understanding is also displayed in terms of the superiorities of
quantitative and qualitative methods to each other which are
evaluated within the scope of these understandings. By way of
assuming that the quantitative researches (modern) are able to
account for structure while the qualitative researches (postmodern)
explain the process, these methods are turned into a means for
worldviews specific to a period. In fact, process is not a functioning
independent of structure. In addition to this issue, the ability of
quantitative methods to provide scientific knowledge is also
controversial so long as they exclude the dialectical method. For this
reason, the critiques charged against modernism in terms of
quantitative methods are, in a sense, legitimate. Nevertheless, the
main issue is in which parameters postmodernist critique tries to
legitimize its critiques and whether these parameters represent a point
of view enabling democratic solutions.
In this respect, the scientific knowledge covered in Turkish media
as a means through which ordinary people have access to scientific
knowledge will be evaluated by means of content analysis within a
new objectivity conception.
Abstract: Disordered function of maniphalanx and difficulty with
ambulation will occur insofar as a human has a failure in the spinal
marrow. Cervical spondylotic myelopathy as one of the myelopathy
emanates from not only external factors but also increased age. In
addition, the diacrisis is difficult since cervical spondylotic
myelopathy is evaluated by a doctor-s neurological remark and
imaging findings. As a quantitative method for measuring the degree
of disability, hand-operated triangle step test (for short, TST) has
formulated. In this research, a full automatic triangle step counter
apparatus is designed and developed to measure the degree of
disability in an accurate fashion according to the principle of TST. The
step counter apparatus whose shape is a low triangle pole displays the
number of stepping upon each corner. Furthermore, the apparatus has
two modes of operation. Namely, one is for measuring the degree of
disability and the other for rehabilitation exercise. In terms of
usefulness, clinical practice should be executed before too long.
Abstract: Certifications such as the Passive House Standard aim to reduce the final space heating energy demand of residential buildings. Space conditioning, notably heating, is responsible for nearly 70% of final residential energy consumption in Europe. There is therefore significant scope for the reduction of energy consumption through improvements to the energy efficiency of residential buildings. However, these certifications totally overlook the energy embodied in the building materials used to achieve this greater operational energy efficiency. The large amount of insulation and the triple-glazed high efficiency windows require a significant amount of energy to manufacture. While some previous studies have assessed the life cycle energy demand of passive houses, including their embodied energy, these rely on incomplete assessment techniques which greatly underestimate embodied energy and can lead to misleading conclusions. This paper analyses the embodied and operational energy demands of a case study passive house using a comprehensive hybrid analysis technique to quantify embodied energy. Results show that the embodied energy is much more significant than previously thought. Also, compared to a standard house with the same geometry, structure, finishes and number of people, a passive house can use more energy over 80 years, mainly due to the additional materials required. Current building energy efficiency certifications should widen their system boundaries to include embodied energy in order to reduce the life cycle energy demand of residential buildings.
Abstract: In this paper, we present user pattern learning
algorithm based MDSS (Medical Decision support system) under
ubiquitous. Most of researches are focus on hardware system, hospital
management and whole concept of ubiquitous environment even
though it is hard to implement. Our objective of this paper is to design
a MDSS framework. It helps to patient for medical treatment and
prevention of the high risk patient (COPD, heart disease, Diabetes).
This framework consist database, CAD (Computer Aided diagnosis
support system) and CAP (computer aided user vital sign prediction
system). It can be applied to develop user pattern learning algorithm
based MDSS for homecare and silver town service. Especially this
CAD has wise decision making competency. It compares current vital
sign with user-s normal condition pattern data. In addition, the CAP
computes user vital sign prediction using past data of the patient. The
novel approach is using neural network method, wireless vital sign
acquisition devices and personal computer DB system. An intelligent
agent based MDSS will help elder people and high risk patients to
prevent sudden death and disease, the physician to get the online
access to patients- data, the plan of medication service priority (e.g.
emergency case).
Abstract: Organizational culture fosters innovation, and innovation is the main engine to be sustained within the uncertainty market. Like other countries, the construction industry significantly contributes to the economy, society and technology of Malaysia, yet, innovation is still considered slow compared to other industries such as manufacturing. Given the important role of an architect as the key player and the contributor of new ideas in the construction industry, there is a call to identify the issue and improve the current situation by focusing on the architectural firms. In addition, the existing studies tend to focus only on a few dimensions of organizational culture and very few studies consider whether innovation is being generated or adopted. Hence, the present research tends to fill in the gap by identifying the organizational cultures that foster or hinder innovation generation and/or innovation adoption, and propose a model of organizational culture and innovation generation and/or adoption.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: Grid composite structures have many applications in aerospace industry in which deal with transverse loadings abundantly. In present paper a stiffened composite cylindrical shell with clamped-free boundary condition under transverse end load experimentally and numerically was studied. Some electrical strain gauges were employed to measure the strains. Also a finite element analysis was done for validation of experimental result. The FEM software used was ANSYS11. In addition, the results between stiffened composite shell and unstiffened composite shell were compared. It was observed that intersection of two stiffeners has an important effect in decrease of stress in the shell. Fairly good agreements were observed between the numerical and the measured results. According to recent studies about grid composite structures, it should be noted that any investigation like this research has not been reported.