Abstract: This paper presents a practical scheme that can be used for allocating the transmission loss to generators and loads. In this scheme first the share of a generator or load on the current through a branch is determined using Z-bus modified matrix. Then the current components are decomposed and the branch loss allocation is obtained. A motivation of proposed scheme is to improve the results of Z-bus method and to reach more fair allocation. The proposed scheme has been implemented and tested on several networks. To achieve practical and applicable results, the proposed scheme is simulated and compared on the transmission network (400kv) of Khorasan region in Iran and the 14-bus standard IEEE network. The results show that the proposed scheme is comprehensive and fair to allocating the energy losses of a power market to its participants.
Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: This paper presents the development and application of an adaptive neuro fuzzy inference system (ANFIS) based intelligent hybrid neuro fuzzy controller for automatic generation control (AGC) of two-area interconnected thermal power system with reheat non linearity. The dynamic response of the system has been studied for 1% step load perturbation in area-1. The performance of the proposed neuro fuzzy controller is compared against conventional proportional-integral (PI) controller, state feedback linear quadratic regulator (LQR) controller and fuzzy gain scheduled proportionalintegral (FGSPI) controller. Comparative analysis demonstrates that the proposed intelligent neuro fuzzy controller is the most effective of all in improving the transients of frequency and tie-line power deviations against small step load disturbances. Simulations have been performed using Matlab®.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Serial Analysis of Gene Expression is a powerful
quantification technique for generating cell or tissue gene expression
data. The profile of the gene expression of cell or tissue in several
different states is difficult for biologists to analyze because of the large
number of genes typically involved. However, feature selection in
machine learning can successfully reduce this problem. The method
allows reducing the features (genes) in specific SAGE data, and
determines only relevant genes. In this study, we used a genetic
algorithm to implement feature selection, and evaluate the
classification accuracy of the selected features with the K-nearest
neighbor method. In order to validate the proposed method, we used
two SAGE data sets for testing. The results of this study conclusively
prove that the number of features of the original SAGE data set can be
significantly reduced and higher classification accuracy can be
achieved.
Abstract: Wavelet transforms are multiresolution
decompositions that can be used to analyze signals and images.
Image compression is one of major applications of wavelet
transforms in image processing. It is considered as one of the most
powerful methods that provides a high compression ratio. However,
its implementation is very time-consuming. At the other hand,
parallel computing technologies are an efficient method for image
compression using wavelets. In this paper, we propose a parallel
wavelet compression algorithm based on quadtrees. We implement
the algorithm using MatlabMPI (a parallel, message passing version
of Matlab), and compute its isoefficiency function, and show that it is
scalable. Our experimental results confirm the efficiency of the
algorithm also.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: In order to accommodate various multimedia
services, next generation wireless networks are characterized
by very high transmission bit rates. Thus, in such systems and
networks, the received signal is not only limited by noise but -
especially with increasing symbols rate often more
significantly by the intersymbol interference (ISI) caused by
the time dispersive radio channels such as those are used in
this work. This paper deals with the study of the performance
of detector for high bit rate transmission on some worst case
models of frequency selective fading channels for outdoor
mobile radio environments. This paper deals with a number of
different wireless channels with different power profiles and
different number of resolvable paths. All the radio channels
generated in this paper are for outdoor vehicular environments
with Doppler spread of 100 Hz. A carrier frequency of 1800
MHz is used and all the channels used in this work are such
that they are useful for next generation wireless systems.
Schemes for mitigation of ISI with adaptive equalizers of
different types have been investigated and their performances
have been investigated in terms of BER measured as a function
of SNR.
Abstract: Over the past few years, a number of efforts have
been exerted to build parallel processing systems that utilize the idle
power of LAN-s and PC-s available in many homes and corporations.
The main advantage of these approaches is that they provide cheap
parallel processing environments for those who cannot afford the
expenses of supercomputers and parallel processing hardware.
However, most of the solutions provided are not very flexible in the
use of available resources and very difficult to install and setup.
In this paper, a multi-level web-based parallel processing system
(MWPS) is designed (appendix). MWPS is based on the idea of
volunteer computing, very flexible, easy to setup and easy to use.
MWPS allows three types of subscribers: simple volunteers (single
computers), super volunteers (full networks) and end users. All of
these entities are coordinated transparently through a secure web site.
Volunteer nodes provide the required processing power needed by
the system end users. There is no limit on the number of volunteer
nodes, and accordingly the system can grow indefinitely. Both
volunteer and system users must register and subscribe. Once, they
subscribe, each entity is provided with the appropriate MWPS
components. These components are very easy to install.
Super volunteer nodes are provided with special components that
make it possible to delegate some of the load to their inner nodes.
These inner nodes may also delegate some of the load to some other
lower level inner nodes .... and so on. It is the responsibility of the
parent super nodes to coordinate the delegation process and deliver
the results back to the user.
MWPS uses a simple behavior-based scheduler that takes into
consideration the current load and previous behavior of processing
nodes. Nodes that fulfill their contracts within the expected time get a
high degree of trust. Nodes that fail to satisfy their contract get a
lower degree of trust.
MWPS is based on the .NET framework and provides the minimal
level of security expected in distributed processing environments.
Users and processing nodes are fully authenticated. Communications
and messages between nodes are very secure. The system has been
implemented using C#.
MWPS may be used by any group of people or companies to
establish a parallel processing or grid environment.
Abstract: Electroencephalogram (EEG) recordings are often
contaminated with ocular and muscle artifacts. In this paper, the
canonical correlation analysis (CCA) is used as blind source
separation (BSS) technique (BSS-CCA) to decompose the artifact
contaminated EEG into component signals. We combine the BSSCCA
technique with wavelet filtering approach for minimizing both
ocular and muscle artifacts simultaneously, and refer the proposed
method as wavelet enhanced BSS-CCA. In this approach, after
careful visual inspection, the muscle artifact components are
discarded and ocular artifact components are subjected to wavelet
filtering to retain high frequency cerebral information, and then clean
EEG is reconstructed. The performance of the proposed wavelet
enhanced BSS-CCA method is tested on real EEG recordings
contaminated with ocular and muscle artifacts, for which power
spectral density is used as a quantitative measure. Our results suggest
that the proposed hybrid approach minimizes ocular and muscle
artifacts effectively, minimally affecting underlying cerebral activity
in EEG recordings.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: The distance protection mainly the impedance relay which is considered as the main protection for transmission lines can be subjected to impedance measurement error which is, mainly, due to the fault resistance and to the power fluctuation. Thus, the impedance relay may not operate for a short circuit at the far end of the protected line (case of the under reach) or operates for a fault beyond its protected zone (case of overreach). In this paper, an approach to fault detection by a distance protection, which distinguishes between the faulty conditions and the effect of overload operation mode, has been developed. This approach is based on the symmetrical components; mainly the negative sequence, and it is taking into account both the effect of fault resistance and the overload situation which both have an effect upon the reliability of the protection in terms of dependability for the former and security for the latter.
Abstract: Multiplication algorithms have considerable effect on
processors performance. A new high-speed, low-power
multiplication algorithm has been presented using modified Dadda
tree structure. Three important modifications have been implemented
in inner product generation step, inner product reduction step and
final addition step. Optimized algorithms have to be used into basic
computation components, such as multiplication algorithms. In this
paper, we proposed a new algorithm to reduce power, delay, and
transistor count of a multiplication algorithm implemented using low
power modified counter. This work presents a novel design for
Dadda multiplication algorithms. The proposed multiplication
algorithm includes structured parts, which have important effect on
inner product reduction tree. In this paper, a 1.3V, 64-bit carry hybrid
adder is presented for fast, low voltage applications. The new 64-bit
adder uses a new circuit to implement the proposed carry hybrid
adder. The new adder using 80 nm CMOS technology has been
implemented on 700 MHz clock frequency. The proposed
multiplication algorithm has achieved 14 percent improvement in
transistor count, 13 percent reduction in delay and 12 percent
modification in power consumption in compared with conventional
designs.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.