Abstract: For this study, a town based soil database created in
Gümüsçay District of Biga Town, Çanakkale, Turkey. Crop and
livestock production are major activities in the district. Nutrient
management is mainly based on commercial fertilizer application
ignoring the livestock manure. Within the boundaries of district, 122
soil sampling points determined over the satellite image. Soil samples
collected from the determined points with the help of handheld
Global Positioning System. Labeled samples were sent to a
commercial laboratory to determine 11 soil parameters including
salinity, pH, lime, organic matter, nitrogen, phosphorus, potassium,
iron, manganese, copper and zinc. Based on the test results soil maps
for mentioned parameters were developed using remote sensing, GIS,
and geostatistical analysis. In this study we developed a GIS database
that will be used for soil nutrient management. Methods were
explained and soil maps and their interpretations were summarized in
the study.
Abstract: Knowledge of bone mechanical properties is important
for bone substitutes design and fabrication, and more efficient
prostheses development. The aim of this study is to characterize the
viscoelastic behavior of bone specimens, through stress relaxation
and fatigue tests performed to trabecular bone samples from bovine
femoral heads. Relaxation tests consisted on preloading the samples
at five different magnitudes and evaluate them for 1020 seconds,
adjusting the results to a KWW mathematical model. Fatigue tests
consisted of 700 load cycles and analyze their status at the end of the
tests. As a conclusion we have that between relaxation stress and
each preload there is linear relation and for samples with initial
Young´s modulus greater than 1.5 GPa showed no effects due fatigue
test loading cycles.
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: It is the worldwide problem that the recycled PVB is
not recycled and it is wildly stored in landfills. However, PVB has
similar chemical properties such as PVC. Moreover, both of these
polymers are plasticized. Therefore, the study of thermal properties
of plasticized PVC and the recycled PVB obtained by recycling of
windshields is carried out. This work has done in order to find nondegradable
processing conditions applicable for both polymers.
Tested PVC contained 38% of plasticizer diisononyl phthalate
(DINP) and PVB was plasticized with 28% of triethylene glycol,
bis(2-ethylhexanoate) (3GO). The thermal and thermo-oxidative
decomposition of both vinyl polymers are compared by calorimetric
analysis and by tensile strength analysis.
Abstract: Whey is the lactose rich by-product of the dairy
industry, having good amount of nutrient reservoir. Most abundant
nutrients are lactose, soluble proteins, lipids and mineral salts.
Disposing of whey by most of milk plants which do not have proper
pre-treatment system is the major issue. As a result of which, there
can be significant loss of potential food and energy source. Thus,
whey has been explored as the substrate for the synthesis of different
value added products such as enzymes. β-galactosidase is one of the
important enzymes and has become the major focus of research due
to its ability to catalyze both hydrolytic as well as
transgalactosylation reaction simultaneously. The enzyme is widely
used in dairy industry as it catalyzes the transformation of lactose to
glucose and galactose, making it suitable for the lactose intolerant
people. The enzyme is intracellular in both bacteria and yeast,
whereas for molds, it has an extracellular location. The present work
was carried to utilize the whey for the production of β-galactosidase
enzyme using both yeast and fungal cultures. The yeast isolate
Kluyveromyces marxianus WIG2 and various fungal strains have
been used in the present study. Different disruption techniques have
also been investigated for the extraction of the enzyme produced
intracellularly from yeast cells. Among the different methods tested
for the disruption of yeast cells, SDS-chloroform showed the
maximum β-galactosidase activity. In case of the tested fungal
cultures, Aureobasidium pullulans NCIM 1050 was observed to be
the maximum extracellular enzyme producer.
Abstract: This paper introduces a video sharing platform based
on WiFi, which consists of camera, mobile phone and PC server. This
platform can receive wireless signal from the camera and show the live
video on the mobile phone captured by camera. In addition, it is able to
send commands to camera and control the camera’s holder to rotate.
The platform can be applied to interactive teaching and dangerous
area’s monitoring and so on. Testing results show that the platform can
share the live video of mobile phone. Furthermore, if the system’s PC
server and the camera and many mobile phones are connected
together, it can transfer photos concurrently.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: Nowadays, the main goal for modern horticultural
production is an increase the quality. In recent years, the use of
organic fertilizers or biostimulants that can be applied in agriculture
to improve quali-quantitative crop yields has encountered increasing
interest. Biostimulants are gaining importance also for their possible
use in organic and sustainable agriculture, to avoid excessive
fertilizer applications. Consecutive experimental trials were carried
out in the Apulia region (southern Italy) on three herbaceous crops
(cauliflower, pepper, fennel) grown in pots under conventional and
organic fertilization systems without and with biostimulants. The aim
was to determine the effects of three biostimulants (Siapton®10L,
Micotech L, Lysodin Alga-Fert) on quali-quantitative yield
characteristics. At harvest, the quali-quantitative yield characteristics
of each crop were determined. All of the experimental data were
subjected to analysis of variance (ANOVA), and when significant
effects were detected, the means were compared using Tukey’s tests.
These data show large differences in these yield characteristics
between conventional and organic crops, particularly highlighting
higher yields for the conventional crops, while variable results were
generally observed when the biostimulants were applied. In this
context, there were no effects of the biostimulants on the quantitative
yield, whereas there were low positive effects on the qualitative
characteristics, as related to higher dry matter content of cauliflower,
and higher soluble solids content of pepper. Moreover, there were
evident positive effects of the biostimulants with fennel, due to the
lower nitrate content. These latter data are in line with most of the
published literature obtained for other herbaceous crops.
Abstract: Fast speed drives for Permanent Magnet Synchronous
Motor (PMSM) is a crucial performance for the electric traction
systems. In this paper, PMSM is derived with a Model-based
Predictive Control (MPC) technique. Fast speed tracking is achieved
through optimization of the DC source utilization using MPC. The
technique is based on predicting the optimum voltage vector applied
to the driver. Control technique is investigated by comparing to the
cascaded PI control based on Space Vector Pulse Width Modulation
(SVPWM). MPC and SVPWM-based FOC are implemented with the
TMS320F2812 DSP and its power driver circuits. The designed MPC
for a PMSM drive is experimentally validated on a laboratory test
bench. The performances are compared with those obtained by a
conventional PI-based system in order to highlight the improvements,
especially regarding speed tracking response.
Abstract: The novel 3D SnO cabbages self-assembled by
nanosheets were successfully synthesized via template-free
hydrothermal growth method under facile conditions. The XRD
results manifest that the as-prepared SnO is tetragonal phase. The
TEM and HRTEM results show that the cabbage nanosheets are
polycrystalline structure consisted of considerable single-crystalline
nanoparticles. Two typical Raman modes A1g=210 and Eg=112 cm-1
of SnO are observed by Raman spectroscopy. Moreover, galvanostatic
cycling tests has been performed using the SnO cabbages as anode
material of lithium ion battery and the electrochemical results suggest
that the synthesized SnO cabbage structures are a promising anode
material for lithium ion batteries.
Abstract: To mitigate the urban heat island effect has become a
global issue when we are faced with the challenge of climate change.
Through literature review, plant photosynthesis can reduce the carbon
dioxide and mitigate the urban heat island effect to a degree. Because
there are not enough open space and parks, green roof has become an
important policy in Taiwan.
We selected elementary school buildings in northern New Taipei
City as research subjects since elementary schools are asked with
priority to build green roof and important educational place to promote
green roof concept. Testo175-H1 recording device was used to record
the temperature and humidity differences between roof surface and
interior space below roof with and without green roof in the long-term.
We also use questionnaires to investigate the awareness of comfort
level of green roof and sensation of teachers and students of the
elementary schools.
The results indicated that the temperature of roof without greening
was higher than that with greening by about 2°C. But sometimes
during noontime, the temperature of green roof was higher than that of
non-green roof probably because of the character of the accumulation
and dissipation of heat of greening. The temperature of the interior
space below green roof was normally lower than that without green
roof by about 1°C, showing that green roof could lower the
temperature. The humidity of the green roof was higher than the one
without greening also indicated that green roof retained water better.
Teachers liked to combine green roof concept in the curriculum,
and students wished all classes can take turns to maintain the green
roof. Teachers and students whose school had integrated green roof
concept in the curriculum were more willing to participate in the
maintenance work of green roof. Teachers and students who may have
access to and touch the green roof can be more aware of the green roof
benefit. We suggest architects to increase the accessibility and
visibility of green roof, such as use it as a part of the activity space.
This idea can be a reference to the green roof curriculum design.
Abstract: Students' academic achievement, along with the
effects of different variables, has been a serious concern of educators
since long ago. This study was an attempt to investigate the interplay
of Locus of Control (LOC), academic achievement and biological
variables among Iranian online EFL Learners. The participants of the
study included 100 students of different age groups and genders
studying English online at Iran Language Institute (ILI), Isfahan,
Iran. The instrument used was Trice Academic LOC questionnaire
which identifies orientations of internality or externality. The
participants' Grade Point Averages (GPAs) were used as the measure
of their academic achievement. A series of independent samples ttests
were performed on the data. The results of the study showed that
(a) there were no significant differences between male and female
participants in LOC orientation, (b) there was no relationship
between LOC and academic achievement among internal males and
females, (c) external females were better achievers than external
males, (d) and the age had no significant relationship with LOC and
academic achievement. It can be concluded that the social, cultural
patterns of genders have changed. This study might help sociologists
and psychologists as well as applied linguists in that they reflect the
recent social changes and their effects on the LOC and their
consequent implications in teaching languages.
Abstract: Development of new generation bio-tribological,
multilayer coatings opens an avenue for fabrication of future hightech
functional surfaces. In the presented work, nano-composite,
Cr/CrN+[Cr/ a-C:H implanted by metallic nanocrystals] multilayer
coatings have been developed for surface protection of medical tools.
Thin films were fabricated by a hybrid Pulsed Laser Deposition
technique. Complex microstructure analysis of nanomultilayer
coatings, subjected to mechanical and biological tests, were
performed by means of transmission electron microscopy (TEM).
Microstructure characterization revealed the layered arrangement of
Cr23C6 nanoparticles in multilayer structure. Influence of deposition
conditions on bio-tribological properties of the coatings was studied.
The bio-tests were used as a screening tool for the analyzed
nanomultilayer coatings before they could be deposited on medical
tools. Bio-medical tests were done using fibroblasts. The mechanical
properties of the coatings were investigated by means of a ball-ondisc
mechanical test. The micro hardness was done using Berkovich
indenter. The scratch adhesion test was done using Rockwell
indenter. From the bio-tribological point of view, the optimal
properties had the C106_1 material.
Abstract: Atmospheric carbon dioxide emissions are considered
as the greatest environmental challenge the world is facing today.
The tasks to control the emissions include the recovery of CO2 from
flue gas. This concern has been improved due to recent advances in
materials process engineering resulting in the development of
inorganic gas separation membranes with excellent thermal and
mechanical stability required for most gas separations. This paper,
therefore, evaluates the performance of a highly selective inorganic
membrane for CO2 recovery applications. Analysis of results
obtained is in agreement with experimental literature data. Further
results show the prediction performance of the membranes for gas
separation and the future direction of research. The materials
selection and the membrane preparation techniques are discussed.
Method of improving the interface defects in the membrane and its
effect on the separation performance has also been reviewed and in
addition advances to totally exploit the potential usage of this
innovative membrane.
Abstract: WO3/SiO2 catalysts were modified by an ion exchange
method with sodium hydroxide or potassium hydroxide solution. The
performance of the modified catalysts was tested in the metathesis of
ethylene and trans-2-butene to propylene. During ion exchange,
sodium and potassium ions played different roles. Sodium modified
catalysts revealed constant trans-2-butene conversion and propylene
selectivity when the concentrations of sodium in the solution were
varied. In contrast, potassium modified catalysts showed reduction of
the conversion and increase of the selectivity. From these results,
potassium hydroxide may affect the transformation of tungsten oxide
active species, resulting in the decrease in conversion whereas
sodium hydroxide did not. Moreover, the modification of catalysts by
this method improved the catalyst stability by lowering the amount of
coke deposited on the catalyst surface.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: Toddy sediment (TS) was cultured in a PDA medium
to determine initial yeast load, and also it was undergone sun, shade,
solar, dehumidified cold air (DCA) and hot air oven (at 400, 500 and
60oC) drying with a view to preserve viability of yeast. Thereafter,
this study was conducted according to two factor factorial design in
order to determine best preservation method. Therein the dried TS
from the best drying method was taken and divided into two portions.
One portion was mixed with 3: 7 ratio of TS: rice flour and the
mixture was divided in to two again. While one portion was kept
under in house condition the other was in a refrigerator. Same
procedure was followed to the rest portion of TS too but it was at the
same ratio of corn flour. All treatments were vacuum packed in triple
laminate pouches and the best preservation method was determined
in terms of leavening index (LI). The TS obtained from the best
preservation method was used to make foods (bread and hopper) and
organoleptic properties of it were evaluated against same of ordinary
foods using sensory panel with a five point hedonic scale.
Results revealed that yeast load or fresh TS was 58×106 CFU/g.
The best drying method in preserving viability of yeast was DCA
because LI of this treatment (96%) is higher than that of other three
treatments. Organoleptic properties of foods prepared from best
preservation method are as same as ordinary foods according to Duo
trio test.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: In this paper, a summary of analytical and
experimental studies into the behavior of a new hysteretic damper,
designed for seismic protection of structures is presented. The Multidirectional
Torsional Hysteretic Damper (MRSD) is a patented
invention in which a symmetrical arrangement of identical cylindrical
steel cores is so configured as to yield in torsion while the structure
experiences planar movements due to earthquake shakings. The new
device has certain desirable properties. Notably, it is characterized by
a variable and controllable-via-design post-elastic stiffness. The
mentioned property is a result of MRSD’s kinematic configuration
which produces this geometric hardening, rather than being a
secondary large-displacement effect. Additionally, the new system is
capable of reaching high force and displacement capacities, shows
high levels of damping, and very stable cyclic response. The device
has gone through many stages of design refinement, multiple
prototype verification tests and development of design guide-lines
and computer codes to facilitate its implementation in practice.
Practicality of the new device, as offspring of an academic sphere, is
assured through extensive collaboration with industry in its final
design stages, prototyping and verification test programs.