Abstract: Shear spinning is closely related to the asymmetric incremental sheet forming (AISF) that could significantly reduce costs incurred by the fabrication of complex aeronautical components with a minimal environmental impact. The spinning experiments were carried out on commercially pure titanium (Ti-Gr2) and Ti-6Al-4V (Ti-Gr5) alloy. Three forming modes were used to characterize the titanium alloys properties from the point of view of different spinning parameters. The structure and properties of the materials were assessed by means of metallographic analyses and microhardness measurements. The highest value wall angle failure limit was achieved using spinning parameters mode for both materials. The feed rate effect was observed only in the samples from the Ti-Gr2 material, when a refinement of the grain microstructure with lower feed rate and higher tangential speed occurred. Ti-Gr5 alloy exhibited a decrease of the microhardness at higher straining due to recovery processes.
Abstract: Induction heating computer simulation is a powerful tool for process design and optimization, induction coil design, equipment selection, as well as education and business presentations. The authors share their vast experience in the practical use of computer simulation for different induction heating and heat treating processes. In this paper treated with mathematical modeling and numerical simulation of induction heating furnaces with axisymmetric geometries for the numerical solution, we propose finite element methods combined with boundary (FEM) for the electromagnetic model using COMSOL® Multiphysics Software. Some numerical results for an industrial furnace are shown with high frequency.
Abstract: Lean technique is very important in the service and industrial fields. It is defined as an effective tool to eliminate the wastes. In lean the wastes are defined as anything which does not add value to the end product. There are wastes that can be avoided, but some are unavoidable for many reasons.
The present study aims to apply the principles of lean in two different sectors, healthcare and industry. Two case studies have been selected to apply the experimental work. The first case was Al-Jalaa Hospital, while the second case study was the Technical Company of Aluminum Sections in Benghazi, LIBYA. In both case studies the Value Stream Map (VSM) of the current state has been constructed. The proposed plans have been implemented by merging or eliminating procedures or processes.
The results obtained from both case studies showed improvement in Capacity, Idle time and Utilized time.
Abstract: Based upon generalized analysis of modern know-how in the sphere of processing, concentration and purification of iron-ore raw materials (IORM), in particular, the most widespread ferrioxide-silicate materials (FOSM), containing impurities of phosphorus and other elements compounds, noted special role of nanotechnological initiatives in improvement of such processes. Considered ideas of role of nanoparticles in processes of FOSM carbonization with subsequent direct reduction of ferric oxides contained in them to metal phase, as well as in processes of alkali treatment and separation of powered iron from phosphorus compounds. Using the obtained results the wasteless method of solid-phase processing, concentration and purification of IORM and FOSM from compounds of phosphorus, silicon and other impurities was developed and it excels known methods of direct iron reduction from iron ores and metallurgical slimes.
Abstract: This paper presents the results of a study aimed at establishing the temperature distribution during the welding of aluminum alloy plates by Pulsed Current Gas Tungsten Arc Welding (PCGTAW) and Constant Current Gas Tungsten Arc Welding (CCGTAW) processes. Pulsing of the GTA welding current influences the dimensions and solidification rate of the fused zone, it also reduces the weld pool volume hence a narrower bead. In this investigation, the base material considered was aluminum alloy AA 6351 T6, which is finding use in aircraft, automobile and high-speed train components. A finite element analysis was carried out using ANSYS, and the results of the FEA were compared with the experimental results. It is evident from the study that the finite element analysis using ANSYS can be effectively used to model PCGTAW process for finding temperature distribution.
Abstract: Conventional coagulation, advance oxidation process (AOPs), and the combined process were evaluated and compared for its suitability to treat the stabilized cutting-oil wastewater. The 90% efficiency was obtained from the coagulation at Al2(SO4)3 dosage of 150 mg/L and pH 7. On the other hands, efficiencies of AOPs for 30 minutes oxidation time were 10% for acoustic oxidation, 12% for acoustic oxidation with hydrogen peroxide, 76% for Fenton, and 92% sono-Fenton processes. The highest efficiency for effective oil removal of AOPs required large amount of chemical. Therefore, AOPs were studied as a post-treatment after conventional separation process. The efficiency was considerable as the effluent COD can pass the standard required for industrial wastewater discharge with less chemical and energy consumption.
Abstract: In this paper subjective film sound will be addressed as it gets represented in narrative cinema. First, “meta-diegetic” sound will be briefly explained followed by transition to “oneiric” sound. The representation of oneiric sound refers to a situation where film characters are experiencing some sort of an altered state of consciousness. Looking at an antlered state of consciousness in terms of human brain processes will point out to the cinematic ways of expression, which “mimic” those processes. Using several examples for different films will illustrate these points.
Abstract: The functional performance of machined components, often, depends on surface topography, hardness, nature of stress and strain induced on the surface, etc. Invariably, surfaces of metallic components obtained by turning, milling, etc., consist of irregularities such as machining marks are responsible for the above. Surface finishing/coating processes used to produce improved surface quality/textures are classified as chip-removal and chip-less processes. Burnishing is chip-less cold working process carried out to improve surface finish, hardness and resistance to fatigue and corrosion; not obtainable by other surface coating and surface treatment processes. It is a very simple, but effective method which improves surface characteristics and is reported to introduce compressive stresses.
Of late, considerable attention is paid to post-machining, finishing operations, such as burnishing. During burnishing the micro-irregularities start to deform plastically, initially the crests are gradually flattened and zones of reduced deformation are formed. When all the crests are deformed, the valleys between the micro-irregularities start moving in the direction of the newly formed surface. The grain structure is then condensed, producing a smoother and harder surface with superior load-carrying and wear-resistant capabilities.
Burnishing can be performed on a lathe with a highly polished ball or roller type tool which is traversed under force over a rotating/stationary work piece. Often, several passes are used to obtain the work piece surface with the desired finish and hardness.
This paper presents the findings of an experimental investigation on the effect of ball burnishing parameters such as, burnishing speed, feed, force and number of passes; on surface roughness (Ra) and micro-hardness (Hv) of a 60/40 copper/zinc alloy, using a 2-level fractional factorial design of experiments (DoE). Mathematical models were developed to predict surface roughness and hardness generated by burnishing in terms of the above process parameters. A ball-type tool, designed and constructed from a high chrome steel material (HRC=63 and Ra=0.012 µm), was used for burnishing of fine-turned cylindrical bars (0.68-0.78µm and 145Hv). They are given by,
Ra= 0.305-0.005X1 - 0.0175X2 + 0.0525X4 + 0.0125X1X4 -0.02X2X4 - 0.0375X3X4
Hv=160.625 -2.37 5X1 + 5.125X2 + 1.875X3 + 4.375X4 - 1.625X1X4 + 4.375X2X4 - 2.375X3X4
High surface microhardness (175HV) was obtained at 400rpm, 2passes, 0.05mm/rev and 15kgf., and high surface finish (0.20µm) was achieved at 30kgf, 0.1mm/rev, 112rpm and single pass. In other words, surface finish improved by 350% and microhardness improved by 21% compared to as machined conditions.
Abstract: Changes in global economy require changes in firms. They need to adapt to speed producing faster and creating new products, structures and processes. The purpose of the paper is to explore literature about organizational culture and its impact on innovation.
In the paper the method of literature review is used to examine influence of organizational culture on innovation and performance of enterprise.
Organizational culture is crucial for innovation. Literature reveals that research of organizational culture mostly confirm already existing conceptions and models, but those help to make profile of innovation culture.
Research summarize previous research of organizational culture as culture which foster innovation and provide profile of innovation culture, which may be used by managers to improve cultural environment to increase performance of their companies. Research also leads to hypothesis for further research.
Abstract: In this study, a new reliable technique use to handle the foam drainage equation. This new method is resulted from VIM by a simple modification that is Reconstruction of Variational Iteration Method (RVIM). The drainage of liquid foams involves the interplay of gravity, surface tension, and viscous forces. Foaming occurs in many distillation and absorption processes. Results are compared with those of Adomian’s decomposition method (ADM).The comparisons show that the Reconstruction of Variational Iteration Method is very effective and overcome the difficulty of traditional methods and quite accurate to systems of non-linear partial differential equations.
Abstract: This work assessed some properties of three pedons on a toposequence in Ijah-Gbagyi district in Niger State, Nigeria. The pedons were designated as JG1, JG2 and JG3 representing the upper, middle and lower slopes respectively. The surface soil was characterized by dark yellowish brown (10YR3/4) color at the JG1 and JG2 and very dark grayish brown (10YR3/2) color at JG3. Sand dominated the mineral fraction and its content in the surface horizon decreased down the slope, whereas silt content increased down the slope due to sorting by geological and pedogenic processes. Although organic carbon (OC), total nitrogen (TN) and available phosphorus (P) were rated high, TN and available P decreased down the slope. High cation exchange capacity (CEC) was an indication that the soils have high potential for plant nutrients retention. The pedons were classified as Typic Haplustepts/ Haplic Cambisols (Eutric), Plinthic Petraquepts/ Petric Plinthosols (Abruptic) and Typic Endoaquepts/ Endogleyic Cambisols (Endoclayic).
Abstract: Electrification is a complex process and governed by various parameters. Modeling of power plant’s target efficiency or target heat rate is often formulated and compared with the actual values. This comparison not only implies the performance of the power plant but also reflects the energy losses possibly inherited in some of related equipment and processes. The current modeling of Coal-fired Mae Moh power plant was formulated at the first commissioning. Some of equipments were replaced due to its life time. Relatively outdated for 20 years, the utilization of the model is not accomplished. This work has focused on the development of the performance analysis model of aforementioned power plant according to the most updated and current working conditions. The model is more appropriate and shows accuracy in its analysis. Losses are detected and measures are introduced such that reduction in energy consumption, related cost, and also environment impacts can be anticipated.
Abstract: The research was accomplished on triticale flour blend, which was made from whole grain triticale, rye, hull-less barley flour and rice, maize flour. The aim of this research was to evaluate physico-chemical and sensory properties of triticale flour blend dough in the mixing and fermentation processes. For dough making was used triticale flour blend, yeast, sugar, salt, and water. In the mixing process ware evaluated moisture, acidity, pH, and dough sensory properties (softness, viscosity, and stickiness), but in the fermentation process ware evaluated volume, moisture, acidity, and pH. During present research was established that increasing fermentation temperature and time, increase dough temperature, volume, moisture, and acidity. The mixing time and fermentation time and temperature have significant effect (p
Abstract: Knowledge is increasingly recognised in this, the
knowledge era, as a strategic resource, by public sector organisations,
in view of the public sector reform initiatives. People and knowledge
play a vital role in attaining improved organisational performance
and high service quality. Many government departments in the public
sector have started to realise the importance of knowledge
management in streamlining their operations and processes. This
study focused on knowledge management in the public healthcare
service organisations, where the concept of service provider
competitiveness pales to insignificance, considering the huge
challenges emanating from the healthcare and public sector reforms.
Many government departments are faced with challenges of
improving organisational performance and service delivery,
improving accountability, making informed decisions, capturing the
knowledge of the aging workforce, and enhancing partnerships with
stakeholders.
The purpose of this paper is to examine the knowledge
management practices of the Gauteng Department of Health in South
Africa, in order to understand how knowledge management practices
influence improvement in organisational performance and healthcare
service delivery. This issue is explored through a review of literature
on dominant views on knowledge management and healthcare service
delivery, as well as results of interviews with, and questionnaire
responses from, the general staff of the Gauteng Department of
Health. Web-based questionnaires, face-to-face interviews and
organisational documents were used to collect data. The data were
analysed using both the quantitative and qualitative methods. The
central question investigated was: To what extent can the conditions
required for successful knowledge management be observed, in order
to improve organisational performance and healthcare service
delivery in the Gauteng Department of Health.
The findings showed that the elements of knowledge management
capabilities investigated in this study, namely knowledge creation,
knowledge sharing and knowledge application, have a positive,
significant relationship with all measures of organisational
performance and healthcare service delivery. These findings thus
indicate that by employing knowledge management principles, the
Gauteng Department of Health could improve its ability to achieve its
operational goals and objectives, and solve organisational and
healthcare challenges, thereby improving organisational performance
and enhancing healthcare service delivery in Gauteng.
Abstract: It can be determined in preference between
representative mechanical and mathematical model of elasticcreeping
deformation of transversally isotropic array with doubly
periodic system of tilted slots, and offer of the finite elements
calculation scheme, and inspection of the states of two diagonal
arbitrary profile cavities of deep inception, and in setting up the tense
and dislocation fields distribution nature in computing processes.
Abstract: Themain goal of this article is to find efficient
methods for elemental and molecular analysis of living
microorganisms (algae) under defined environmental conditions and
cultivation processes. The overall knowledge of chemical
composition is obtained utilizing laser-based techniques, Laser-
Induced Breakdown Spectroscopy (LIBS) for acquiring information
about elemental composition and Raman Spectroscopy for gaining
molecular information, respectively. Algal cells were suspended in
liquid media and characterized using their spectra. Results obtained
employing LIBS and Raman Spectroscopy techniques will help to
elucidate algae biology (nutrition dynamics depending on cultivation
conditions) and to identify algal strains, which have the potential for
applications in metal-ion absorption (bioremediation) and biofuel
industry. Moreover, bioremediation can be readily combined with
production of 3rd generation biofuels. In order to use algae for
efficient fuel production, the optimal cultivation parameters have to
be determinedleading to high production of oil in selected
cellswithout significant inhibition of the photosynthetic activity and
the culture growth rate, e.g. it is necessary to distinguish conditions
for algal strain containing high amount of higher unsaturated fatty
acids. Measurements employing LIBS and Raman Spectroscopy were
utilized in order to give information about alga Trachydiscusminutus
with emphasis on the amount of the lipid content inside the algal cell
and the ability of algae to withdraw nutrients from its environment
and bioremediation (elemental composition), respectively. This
article can serve as the reference for further efforts in describing
complete chemical composition of algal samples employing laserablation
techniques.
Abstract: Nowadays, more engineering systems are using some
kind of Artificial Intelligence (AI) for the development of their
processes. Some well-known AI techniques include artificial neural
nets, fuzzy inference systems, and neuro-fuzzy inference systems
among others. Furthermore, many decision-making applications base
their intelligent processes on Fuzzy Logic; due to the Fuzzy
Inference Systems (FIS) capability to deal with problems that are
based on user knowledge and experience. Also, knowing that users
have a wide variety of distinctiveness, and generally, provide
uncertain data, this information can be used and properly processed
by a FIS. To properly consider uncertainty and inexact system input
values, FIS normally use Membership Functions (MF) that represent
a degree of user satisfaction on certain conditions and/or constraints.
In order to define the parameters of the MFs, the knowledge from
experts in the field is very important. This knowledge defines the MF
shape to process the user inputs and through fuzzy reasoning and
inference mechanisms, the FIS can provide an “appropriate" output.
However an important issue immediately arises: How can it be
assured that the obtained output is the optimum solution? How can it
be guaranteed that each MF has an optimum shape? A viable solution
to these questions is through the MFs parameter optimization. In this
Paper a novel parameter optimization process is presented. The
process for FIS parameter optimization consists of the five simple
steps that can be easily realized off-line. Here the proposed process
of FIS parameter optimization it is demonstrated by its
implementation on an Intelligent Interface section dealing with the
on-line customization / personalization of internet portals applied to
E-commerce.
Abstract: Fault tolerance is critical in many of today's large computer systems. This paper focuses on improving fault tolerance through testing. Moreover, it concentrates on the memory faults: how to access the editable part of a process memory space and how this part is affected. A special Software Fault Injection Technique (SFIT) is proposed for this purpose. This is done by sequentially scanning the memory of the target process, and trying to edit maximum number of bytes inside that memory. The technique was implemented and tested on a group of programs in software packages such as jet-audio, Notepad, Microsoft Word, Microsoft Excel, and Microsoft Outlook. The results from the test sample process indicate that the size of the scanned area depends on several factors. These factors are: process size, process type, and virtual memory size of the machine under test. The results show that increasing the process size will increase the scanned memory space. They also show that input-output processes have more scanned area size than other processes. Increasing the virtual memory size will also affect the size of the scanned area but to a certain limit.
Abstract: Enzymatic hydrolysis is one of the major steps involved in the conversion from sugarcane bagasse to yield ethanol. This process offers potential for yields and selectivity higher, lower energy costs and milder operating conditions than chemical processes. However, the presence of some factors such as lignin content, crystallinity degree of the cellulose, and particle sizes, limits the digestibility of the cellulose present in the lignocellulosic biomasses. Pretreatment aims to improve the access of the enzyme to the substrate. In this study sugarcane bagasse was submitted chemical pretreatment that consisted of two consecutive steps, the first with dilute sulfuric acid (1 % (v/v) H2SO4), and the second with alkaline solutions with different concentrations of NaOH (1, 2, 3 and 4 % (w/v)). Thermal Analysis (TG/ DTG and DTA) was used to evaluate hemicellulose, cellulose and lignin contents in the samples. Scanning Electron Microscopy (SEM) was used to evaluate the morphological structures of the in natura and chemically treated samples. Results showed that pretreatments were effective in chemical degradation of lignocellulosic materials of the samples, and also was possible to observe the morphological changes occurring in the biomasses after pretreatments.
Abstract: Creation and maintenance of knowledge management
systems has been recognized as an important research area.
Consecutively lack of accurate results from knowledge management
systems limits the organization to apply their knowledge
management processes. This leads to a failure in getting the right
information to the right people at the right time thus followed by a
deficiency in decision making processes. An Intranet offers a
powerful tool for communication and collaboration, presenting data
and information, and the means that creates and shares knowledge,
all in one easily accessible place. This paper proposes an archetype
describing how a knowledge management system, with the support
of intranet capabilities, could very much increase the accuracy of
capturing, storing and retrieving knowledge based processes thereby
increasing the efficiency of the system. This system will expect a
critical mass of usage, by the users, for intranet to function as
knowledge management systems. This prototype would lead to a
design of an application that would impose creation and maintenance
of an effective knowledge management system through intranet. The
aim of this paper is to introduce an effective system to handle
capture, store and distribute knowledge management in a form that
may not lead to any failure which exists in most of the systems. The
methodology used in the system would require all the employees, in
the organization, to contribute the maximum to deliver the system to
a successful arena. The system is still in its initial mode and thereby
the authors are under the process to practically implement the ideas,
as mentioned in the system, to produce satisfactory results.