Abstract: A statistical optimization was studied to design a media composition to produce optimum cellulolytic enzyme where palm oil mill effluent (POME) as a basal medium and filamentous fungus, Trichoderma reesei RUT-C30 were used in the liquid state bioconversion(LSB). 2% (w/v) total suspended solid, TSS, of the POME supplemented with 1% (w/v) cellulose, 0.5%(w/v) peptone and 0.02% (v/v) Tween 80 was estimated to produce the optimum CMCase activity of 18.53 U/ml through the statistical analysis followed by the faced centered central composite design(FCCCD). The probability values of cellulose (
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Abstract: This paper presents the comparative study of coded
data methods for finding the benefit of concealing the natural data
which is the mercantile secret. Influential parameters of the number
of replicates (rep), treatment effects (τ) and standard deviation (σ)
against the efficiency of each transformation method are investigated.
The experimental data are generated via computer simulations under
the specified condition of the process with the completely
randomized design (CRD). Three ways of data transformation consist
of Box-Cox, arcsine and logit methods. The difference values of F
statistic between coded data and natural data (Fc-Fn) and hypothesis
testing results were determined. The experimental results indicate
that the Box-Cox results are significantly different from natural data
in cases of smaller levels of replicates and seem to be improper when
the parameter of minus lambda has been assigned. On the other hand,
arcsine and logit transformations are more robust and obviously,
provide more precise numerical results. In addition, the alternate
ways to select the lambda in the power transformation are also
offered to achieve much more appropriate outcomes.
Abstract: An overview of the important aspects of managing
and controlling industrial effluent discharges to public sewers namely
sampling, characterization, quantification and legislative controls has
been presented. The findings have been validated by means of a case
study covering three industrial sectors namely, tanning, textile
finishing and food processing industries. Industrial effluents
discharges were found to be best monitored by systematic and
automatic sampling and quantified using water meter readings
corrected for evaporative and consumptive losses. Based on the
treatment processes employed in the public owned treatment works
and the chemical oxygen demand and biochemical oxygen demand
levels obtained, the effluent from all the three industrial sectors
studied were found to lie in the toxic zone. Thus, physico-chemical
treatment of these effluents is required to bring them into the
biodegradable zone. KL values (quoted to base e) were greater than
0.50 day-1 compared to 0.39 day-1 for typical municipality
wastewater.
Abstract: This paper presents the prediction of air flow,
humidity and temperature patterns in a co-current pilot plant spray
dryer fitted with a pressure nozzle using a three dimensional model.
The modelling was done with a Computational Fluid Dynamic
package (Fluent 6.3), in which the gas phase is modelled as
continuum using the Euler approach and the droplet/ particle phase is
modelled by the Discrete Phase model (Lagrange approach).Good
agreement was obtained with published experimental data where the
CFD simulation correctly predicts a fast downward central flowing
core and slow recirculation zones near the walls. In this work, the
effects of the air flow pattern on droplets trajectories, residence time
distribution of droplets and deposition of the droplets on the wall also
were investigated where atomizing of maltodextrin solution was
used.
Abstract: This article deals with numerical simulation of the
floor heating convector in 3D. Numerical simulation is focused on
cooling mode of the floor heating convector. Geometrical model
represents section of the heat exchanger – two fins with the gap
between, pipes are not involved. Two types of fin are examined –
sinusoidal and angular shape with different fin spacing. Results of fin
spacing in case of constant Reynolds number are presented. For the
numerical simulation was used commercial software Ansys Fluent.
Abstract: This research is aimed to describe the application of robust regression and its advantages over the least square regression method in analyzing financial data. To do this, relationship between earning per share, book value of equity per share and share price as price model and earning per share, annual change of earning per share and return of stock as return model is discussed using both robust and least square regressions, and finally the outcomes are compared. Comparing the results from the robust regression and the least square regression shows that the former can provide the possibility of a better and more realistic analysis owing to eliminating or reducing the contribution of outliers and influential data. Therefore, robust regression is recommended for getting more precise results in financial data analysis.
Abstract: This study was initiated with a three prong objective.
One, to identify the relationship between Technological
Competencies factors (Technical Capability, Firm Innovativeness
and E-Business Practices and professional service firms- business
performance. To investigate the predictors of professional service
firms business performance and finally to evaluate the predictors of
business performance according to the type of professional service
firms, a survey questionnaire was deployed to collect empirical data.
The questionnaire was distributed to the owners of the professional
small medium size enterprises services in the Accounting, Legal,
Engineering and Architecture sectors. Analysis showed that all three
Technology Competency factors have moderate effect on business
performance. In addition, the regression models indicate that
technical capability is the most highly influential that could
determine business performance, followed by e-business practices
and firm innovativeness. Subsequently, the main predictor of
business performance for all types of firms is Technical capability.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: An attempt has been made to investigate the
machinability of zirconia toughened alumina (ZTA) inserts while
turning AISI 4340 steel. The insert was prepared by powder
metallurgy process route and the machining experiments were
performed based on Response Surface Methodology (RSM) design
called Central Composite Design (CCD). The mathematical model of
flank wear, cutting force and surface roughness have been developed
using second order regression analysis. The adequacy of model has
been carried out based on Analysis of variance (ANOVA) techniques.
It can be concluded that cutting speed and feed rate are the two most
influential factor for flank wear and cutting force prediction. For
surface roughness determination, the cutting speed & depth of cut
both have significant contribution. Key parameters effect on each
response has also been presented in graphical contours for choosing
the operating parameter preciously. 83% desirability level has been
achieved using this optimized condition.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Temperature, humidity and precipitation in an area,
are parameters proved influential in the climate of that area, and one
should recognize them so that he can determine the climate of that
area. Climate changes are of primary importance in climatology, and
in recent years, have been of great concern to researchers and even
politicians and organizations, for they can play an important role in
social, political and economic activities. Even though the real cause
of climate changes or their stability is not yet fully recognized, they
are a matter of concern to researchers and their importance for
countries has prompted them to investigate climate changes in
different levels, especially in regional, national and continental level.
This issue has less been investigated in our country. However, in
recent years, there have been some researches and conferences on
climate changes. This study is also in line with such researches and
tries to investigate and analyze the trends of climate changes
(temperature and precipitation) in Sefid-roud (the name of a river)
basin. Three parameters of mean annual precipitation, temperature,
and maximum and minimum temperatures in 36 synoptic and
climatology stations in a statistical period of 49 years (1956-2005) in
the stations of Sefid-roud basin were analyzed by Mann-Kendall test.
The results obtained by data analysis show that climate changes are
short term and have a trend. The analysis of mean temperature
revealed that changes have a significantly rising trend, besides the
precipitation has a significantly falling trend.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: A shaft-type activated sludge reactor has been
developed in order to study the feasibility of high-rate wastewater
treatment. The reactor having volume of about 14.5 L was operated
with the acclimated mixed activated sludge under batch and
continuous mode using a synthetic wastewater as feed. The batch
study was performed with varying chemical oxygen demand (COD)
concentrations of 1000–3500 mg·L-1 for a batch period up to 9 h. The
kinetic coefficients: Ks, k, Y and kd were obtained as 2040.2 mg·L-1
and 0.105 h-1, 0.878 and 0.0025 h-1 respectively from Monod-s
approach. The continuous study showed a stable and steady state
operation for a hydraulic retention time (HRT) of 8 h and influent
COD of about 1000 mg·L-1. A maximum COD removal efficiency of
about 80% was attained at a COD loading rate and food-tomicroorganism
(F/M) ratio (COD basis) of 3.42 kg·m-3d-1 and 1.0
kg·kg-1d-1 respectively under a HRT of 8 h. The reactor was also
found to handle COD loading rate and F/M ratio of 10.8 kg·m-3d-1
and 2.20 kg·kg-1d-1 respectively showing a COD removal efficiency
of about 46%.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: The effects of irrigation with dairy factory wastewater on soil properties were investigated at two sites that had received irrigation for > 60 years. Two adjoining paired sites that had never received DFE were also sampled as well as another seven fields from a wider area around the factory. In comparison with paired sites that had not received effluent, long-term wastewater irrigation resulted in an increase in pH, EC, extractable P, exchangeable Na and K and ESP. These changes were related to the use of phosphoric acid, NaOH and KOH as cleaning agents in the factory. Soil organic C content was unaffected by DFE irrigation but the size (microbial biomass C and N) and activity (basal respiration) of the soil microbial community were increased. These increases were attributed to regular inputs of soluble C (e.g. lactose) present as milk residues in the wastewater. Principal component analysis (PCA) of the soils data from all 11sites confirmed that the main effects of DFE irrigation were an increase in exchangeable Na, extractable P and microbial biomass C, an accumulation of soluble salts and a liming effect. PCA analysis of soil bacterial community structure, using PCR-DGGE of 16S rDNA fragments, generally separated individual sites from one another but did not group them according to irrigation history. Thus, whilst the size and activity of the soil microbial community were increased, the structure and diversity of the bacterial community remained unaffected.
Abstract: The sonochemical decolorization and degradation of azo dye Methyl violet using Fenton-s reagent in the presence of a high-frequency acoustic field has been investigated. Dyeing and textile effluents are the major sources of azo dyes, and are most troublesome among industrial wastewaters, causing imbalance in the eco-system. The effect of various operating conditions (initial concentration of dye, liquid-phase temperature, ultrasonic power and frequency and process time) on sonochemical degradation was investigated. Conversion was found to increase with increase in initial concentration, temperature, power level and frequency. Both horntype and tank-type sonicators were used, at various power levels (250W, 400W and 500W) for frequencies ranging from 20 kHz - 1000 kHz. A 'Process Intensification' parameter PI, was defined to quantify the enhancement of the degradation reaction by ultrasound when compared to control (i.e., without ultrasound). The present work clearly demonstrates that a high-frequency ultrasonic bath can be used to achieve higher process throughput and energy efficiency at a larger scale of operation.
Abstract: When the crisscross baffles and logarithmic spiral
baffles are placed on the bottom of the stirred tank with elliptic
bottom, using CFD software FLUENT simulates the velocity field of
the stirred tank with elliptic bottom and bottom baffles. Compare the
velocity field of stirred tank with bottom crisscross baffle to the
velocity field of stirred tank without bottom baffle and analysis the
flow pattern on the same axis-section and different cross-sections. The
sizes of the axial and radial velocity are compared respectively when
the stirred tank with bottom crisscross baffles, bottom logarithmic
spiral baffles and without bottom baffle. At the same time, the
numerical calculations of mixing power are compared when the stirred
tank with bottom crisscross baffles and bottom logarithmic spiral
baffles. Research shows that bottom crisscross baffles and logarithmic
spiral baffles have a great impact on flow pattern within the reactor
and improve the mixing effect better than without baffle. It also has
shown that bottom logarithmic spiral baffles has lower power
consumption than bottom crisscross baffles.
Abstract: The present study was performed in Musa bay (northern part of the Persian Gulf) around the coastal area of Bandare-Imam Khomeini and Razi Petrochemical Companies. Sediment samples and effluent samples were collected from the selected stations, from June 2009 to June 2010. The samples were analyzed to determine the degree of hydrocarbon contamination. The average level of TPH concentration in the study area was more than the natural background value at all of the stations, especially at station BI1 which was the main effluent outlet of Bandar-e- Imam Khomeini petrochemical company. Also the concentration of total petroleum hydrocarbon was monitored in the effluents of aforementioned petrochemical companies and the results showed that the concentration of TPH in the effluents of Bandar-e- Imam Khomeini petrochemical company was greater than Razi petrochemical company which is may be related to the products of Bandar-e- Imam Khomeini petrochemical company (aromatics, polymers, chemicals, fuel).