CFD Simulations of a Co-current Spray Dryer

This paper presents the prediction of air flow, humidity and temperature patterns in a co-current pilot plant spray dryer fitted with a pressure nozzle using a three dimensional model. The modelling was done with a Computational Fluid Dynamic package (Fluent 6.3), in which the gas phase is modelled as continuum using the Euler approach and the droplet/ particle phase is modelled by the Discrete Phase model (Lagrange approach).Good agreement was obtained with published experimental data where the CFD simulation correctly predicts a fast downward central flowing core and slow recirculation zones near the walls. In this work, the effects of the air flow pattern on droplets trajectories, residence time distribution of droplets and deposition of the droplets on the wall also were investigated where atomizing of maltodextrin solution was used.

Authors:



References:
[1] Masters, K., Spray Drying Handbook, 4th ed., John Wiley and Sons,
New York, 1985.
[2] Oakley, D.E., Produce uniform particles by spray drying, Chem. Eng.
Prog., October, pp. 48-54, 1997.
[3] Harvie, D.J.E.; Langrish, T.A.G ;Fletcher D.F., A computational fluid
dynamics study of a tall-form spray dryer,Trans. IChemE, 80(3), pp.
163-175, 2002.
[4] Harvie, D.J.E.; Langrish, T.A.G.; Fletcher, D.F., Numerical simulations
of gas flow patterns within a tall-form spray dryer, Trans. IChemE,79
(3) A, pp. 235-248, 2001.
[5] Oakley, D.E.; Bahu, R.E.,Computational modeling of spray drying,
Comput. Chem. Eng. 17, pp. 493-498,1993.
[6] Kieviet, F.G.,Modelling Quality in Spray Drying,Ph.D. thesis,
Endinhoven University of Technology, the Netherland, 1997.
[7] Southwell, D.B.; Langrish, T.A.G.,Observations of flow patterns in a
spray dryer, Drying Technology, 18 (3),pp. 661-685, 2000.
[8] Langrish, T.A.G.; Fletcher, D.F., Prospects for the Modelling and
Design of Spray Dryers in the 21st Century. Drying Technology, 21 (2),
pp. 197-215, 2003.
[9] Sommerfeld, M.,Review on numerical modeling of dispersed two phase
flows, Proc. 5th Int.Symp. on Refined Flow Modelling and Turbulence
Measurements, Paris, 1993.
[10] Crowe, C.T.; Sharma, M.P. ; Stock, D.E. The particle-source-in-cell
(PSI-Cell) model for gas-droplet flows, Journal of Fluid Engineering,
99, pp. 325-332, 1977.
[11] Fluent Manual, Chap. 23: Discrete phase models, www.fluent.com,
2006.
[12] Haung, L.; Kumar, K.; Mujumdar, A. S.,A Pararmeteric Study of the
Gas Flow Patterns and Drying Performance Of Co- current Spray
Dryer, Drying Technology, 21, 6, pp. 957-978, 2003.
[13] Langrish,T.A.G.; Kockel,T.K., The implementation of a characteristic
drying curve for milk powder using a computational fluid dynamics
simulation, Chem. Eng. J., 83 (4), pp. 69-74,2001.
[14] Keey, R. , Drying of Loose and Particulate Matter, 1st edn, Hemisphere
Publishing Corporation , 1992.
[15] Woo, M.w. ;Daud, W.R.; Mujumdar, A.S.; Talib, M.Z.; Hua,W.Z. and
Tarsirin,S. M., Comparative study of droplet drying models for CFD
modeling, Chem.Eng. Res.and Des.,86,pp. 1038-1048,2008.
[16] Truong, V.; Bhandari, B.R.;Howes, T., Optimization of co-current spray
drying process of sugar-rich foods. Part IÔÇömoisture and glass transition
temperature profile during drying, Journal of Food Engineering 71 (1),
pp. 55-65,2005.
[17] Handscomb, C., Kraft, M., Bayly, A., Spray Drying Modelling,
University of Cambridge, 2005.
[18] Ranz, W.; Marshall,W., Evaporation from drops. Chem Eng.
Prog.,48(141),pp. 173,1952.
[19] Reay, D., Modelling continuous convection dryers for particulate solidsprogress
and problems, Drying -85, 5,pp. 67-74, 1985.
[20] Elghobashi, S.,On predicting particle-laden turbulent flows, Applied
Scientific Research, 52,pp. 309-329, 1994.
[21] Kerkhof, P.J.A.M.; Schoeber,W.J.A.H., Theortical modeling of the
drying behaviour of droplet in spray dryers, Advances in
preconcentration and dehydration of foods, ed. A. Spicer, Applied
science publisher, London, pp. 349-397, 1974.
[22] Kota, K.; Langrish, T., Prediction of Deposition Patterns in a Pilot-Scale
Spray Dryer Using CFD Simulations, Chem. Prod. and Proc. Modeling,
2(3), 26, 2007.