Abstract: This study aims to analyze the effect of e-learning on
photonics technology and daily livings among college students. The
course contents of photonics technology and daily livings are first
drafted based on research discussions and expert interviews. Having
expert questionnaires with Delphi Technique for three times, the
knowledge units and items for the course of photonics technology and
daily livings are established. The e-learning materials and the drafts of
instructional strategies, academic achievement, and learning attitude
scales are then developed. With expert inspection, reliability and
validity test, and experimental instructions, the scales and the material
are further revised. Finally, the formal instructions are implemented to
test the effect of different instructional methods on the academic
achievement of photonics technology and daily livings among students
in universities of technology. The research results show that e-learning
could effectively promote academic achievement and learning
attitude, and the students with e-learning obviously outperform the
ones with trandition instructions.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: In technological processes, in addition to the main
product, result a large amount of materials, called wastes, but due to
the possibilities of recovery, by means of recycling and reusing it can
fit in the category of by-products. These large amounts of dust from
the steel industry are a major problem in terms of environmental and
human health, landscape, etc. Solving these problems, the impressive
amounts of waste can be done through their proper management and
recovery for every type of waste. In this article it was watched the
capitalizing through pelleting and briquetting of small and powdery
waste aiming to obtain the sponge iron as raw material, used in blast
furnaces and electric arc furnaces. The data have been processed in
the Excel spreadsheet program, being presented in the form of
diagrams.
Abstract: In this paper, an erosion-based model for abrasive
waterjet (AWJ) turning process is presented. By using modified
Hashish erosion model, the volume of material removed by impacting
of abrasive particles to surface of the rotating cylindrical specimen is
estimated and radius reduction at each rotation is calculated.
Different to previous works, the proposed model considers the
continuous change in local impact angle due to change in workpiece
diameter, axial traverse rate of the jet, the abrasive particle roundness
and density. The accuracy of the proposed model is examined by
experimental tests under various traverse rates. The final diameters
estimated by the proposed model are in good accordance with
experiments.
Abstract: Municipal solid waste (MSW) comprises of a wide
range of heterogeneous materials generated by individual, household
or organization and may include food waste, garden wastes, papers,
textiles, rubbers, plastics, glass, ceramics, metals, wood wastes,
construction wastes but it is not limited to the above mentioned
fractions. The most common Municipal Solid Waste pretreatment
method in use is thermal pretreatment (incineration) and Mechanical
Biological pretreatment. This paper presents an overview of these
two pretreatment methods describing their benefits and laboratory
scale reactors that simulate landfill conditions were constructed in
order to compare emissions in terms of biogas production and
leachate contamination between untreated Municipal Solid Waste and
Mechanical Biological Pretreated waste. The findings of this study
showed that Mechanical Biological pretreatment of waste reduces the
emission level of waste and the benefit over the landfilling of
untreated waste is significant.
Abstract: Unsteady boundary layer flow of an incompressible
micropolar fluid over a stretching sheet when the sheet is stretched in
its own plane is studied in this paper. The stretching velocity is
assumed to vary linearly with the distance along the sheet. Two equal
and opposite forces are impulsively applied along the x-axis so that the
sheet is stretched, keeping the origin fixed in a micropolar fluid. The
transformed unsteady boundary layer equations are solved
numerically using the Keller-box method for the whole transient from
the initial state to final steady-state flow. Numerical results are
obtained for the velocity and microrotation distributions as well as the
skin friction coefficient for various values of the material parameter K.
It is found that there is a smooth transition from the small-time
solution to the large-time solution.
Abstract: This study aimed to explore future life orientation and
support that needed to accomplish it. A total of 258 participants are
Javanese high school student. The age of the sample ranges from 14
to 18 years old. Participants were asked about their future aspiration,
their reason of choosing them as important goals in their life, and
support that they need to accomplished their goals using open ended
questionnaire. The responses were categorized through content
analysis into four main categories. They are: (1) Self Fulfillment
(72.1%) (2) Parents and Family (16.7%) (3) Altruism (8.1%) (4)
Social and Economy Status (3.1%). Meanwhile, the categories for
support that they needed are shown as follows: (1) Affection Support
(64.7%) (2) Spiritual support (17.4%) (3) Material Support (10.9%)
(4) Guidance Support (7.0%). The research found that affection
support always gets the highest number in every future orientation
categories. It can be concluded that although Javanese adolescents
have different future orientation, they basically need affection
support.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.
Abstract: This paper investigates the use of mobile phones and
tablets for learning purposes among university students in Saudi
Arabia. For this purpose, an extended Technology Acceptance Model
(TAM) is proposed to analyze the adoption of mobile devices and
smart phones by Saudi university students for accessing course
materials, searching the web for information related to their
discipline, sharing knowledge, conducting assignments etc.
Abstract: Availability of raw materials is important for
Indonesia as a furniture exporting country. Teak log as raw materials
is supplied to the furniture industry by Perum Perhutani (PP). PP
needs to involve carbon trading for nature conservation. PP also has
an obligation in the Corporate Social Responsibility program. PP and
furniture industry also must prosecute the regulations related to
ecological issues and labor rights. This study has the objective to
create the relationship model between supplier and manufacturer to
fulfill teak log demand that involving teak forest carbon
sequestration. A model is formulated as Goal Programming to get the
favorable solution for teak log procurement and support carbon
sequestration that considering economical, ecological, and social
aspects of both supplier and manufacturer. The results show that the
proposed model can be used to determine the teak log quantity
involving carbon trading to achieve the seven goals to be satisfied the
sustainability considerations.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: The work presents a development of EN338 strength classes for Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum Nigerian timber species. The specimens for experimental measurements were obtained from the timber-shed at the famous Panteka market in Kaduna in the northern part of Nigeria. Laboratory experiments were conducted to determine the physical and mechanical properties of the selected timber species in accordance with EN 13183-1 and ASTM D193. The mechanical properties were determined using three point bending test. The generated properties were used to obtain the characteristic values of the material properties in accordance with EN384. The selected timber species were then classified according to EN 338. Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum were assigned to strength classes D40, C14, D40 and D24 respectively. Other properties such as tensile and compressive strengths parallel and perpendicular to grains, shear strength as well as shear modulus were obtained in accordance with EN 338.
Abstract: A measurement apparatus is designed and fabricated to
measure the effective thermal conductivity (keff) of a VIP (vacuum
insulation panel) core specimen under various vacuum states and
external loads. The apparatus consists of part for measuring keff, and
parts for controlling external load and vacuum condition. Uncertainty
of the apparatus is validated by measuring the standard reference
material and comparing with commercial devices with VIP samples.
Assessed uncertainty is maximum 2.5 % in case of the standard
reference material, 10 % in case of VIP samples. Using the apparatus,
keff of glass paper under various vacuum levels is examined.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: Anodizing is an electrochemical process that converts the metal surface into a decorative, durable, corrosion-resistant, anodic oxide finish. Aluminum is ideally suited to anodizing, although other nonferrous metals, such as magnesium and titanium, also can be anodized. The anodic oxide structure originates from the aluminum substrate and is composed entirely of aluminum oxide. This aluminum oxide is not applied to the surface like paint or plating, but is fully integrated with the underlying aluminum substrate, so cannot chip or peel. It has a highly ordered, porous structure that allows for secondary processes such as coloring and sealing. In this experimental paper, we focus on a reliable method for fabricating nanoporous alumina with high regularity. Starting from study of nanostructure materials synthesize methods. After that, porous alumina fabricate in the laboratory by anodization of aluminum oxide. Hard anodization processes are employed to fabricate the nanoporous alumina using 0.3M oxalic acid and 90, 120 and 140 anodized voltages. The nanoporous templates were characterized by SEM and FFT. The nanoporous templates using 140 voltages have high ordered. The pore formation, influence of the experimental conditions on the pore formation, the structural characteristics of the pore and the oxide chemical reactions involved in the pore growth are discuss.
Abstract: The field of polymeric biomaterials is very important
from the socio-economical viewpoint. Synthetic carbohydrate
polymers are being increasingly investigated as biodegradable,
biocompatible and biorenewable materials. The aim of this study was
to synthesize and characterize some derivatives based on D-mannose.
D-mannose was chemically modified to obtain 1-O-allyl-2,3:5,6-di-
O-isopropylidene-D-mannofuranose and 1-O-(2-,3--epoxy-propyl)-
2,3:5,6-di-O-isopropylidene-D-mannofuranose.
The chemical structure of the resulting compounds was
characterized by FT-IR and NMR spectroscopy, and by HPLC-MS.
Abstract: Near-infrared (NIR) spectroscopy is a widely used
method for material identification for laboratory and industrial applications.
While standard spectrometers only allow measurements at
one sampling point at a time, NIR Spectral Imaging techniques can
measure, in real-time, both the size and shape of an object as well as
identify the material the object is made of. The online classification
and sorting of recovered paper with NIR Spectral Imaging (SI)
is used with success in the paper recycling industry throughout
Europe. Recently, the globalisation of the recycling material streams
caused that water-based flexographic-printed newspapers mainly from
UK and Italy appear also in central Europe. These flexo-printed
newspapers are not sufficiently de-inkable with the standard de-inking
process originally developed for offset-printed paper. This de-inking
process removes the ink from recovered paper and is the fundamental
processing step to produce high-quality paper from recovered paper.
Thus, the flexo-printed newspapers are a growing problem for the
recycling industry as they reduce the quality of the produced paper
if their amount exceeds a certain limit within the recovered paper
material.
This paper presents the results of a research project for the
development of an automated entry inspection system for recovered
paper that was jointly conducted by CTR AG (Austria) and PTS
Papiertechnische Stiftung (Germany). Within the project an NIR
SI prototype for the identification of flexo-printed newspaper has
been developed. The prototype can identify and sort out flexoprinted
newspapers in real-time and achieves a detection accuracy
for flexo-printed newspaper of over 95%. NIR SI, the technology the
prototype is based on, allows the development of inspection systems
for incoming goods in a paper production facility as well as industrial
sorting systems for recovered paper in the recycling industry in the
near future.
Abstract: Particulate reinforced metal matrix composites
(MMCs) are potential materials for various applications due to their
advantageous of physical and mechanical properties. This paper
presents a study on the performance of stir cast Al2O3 SiC reinforced
metal matrix composite materials. The results indicate that the
composite materials exhibit improved physical and mechanical
properties, such as, low coefficient of thermal expansion, high
ultimate tensile strength, high impact strength, and hardness. It has
been found that with the increase of weight percentage of
reinforcement particles in the aluminium metal matrix, the new
material exhibits lower wear rate against abrasive wearing. Being
extremely lighter than the conventional gray cast iron material, the
Al-Al2O3 and Al-SiC composites could be potential green materials
for applications in the automobile industry, for instance, in making
car disc brake rotors.