Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: Cortisol is essential to the regulation of the immune
system and pathological yawning is a symptom of multiple sclerosis
(MS). Electromyography activity (EMG) in the jaw muscles typically
rises when the muscles are moved – extended or flexed; and yawning
has been shown to be highly correlated with cortisol levels in healthy
people as shown in the Thompson Cortisol Hypothesis. It is likely
that these elevated cortisol levels are also seen in people with MS.
The possible link between EMG in the jaw muscles and rises in saliva
cortisol levels during yawning were investigated in a randomized
controlled trial of 60 volunteers aged 18-69 years who were exposed
to conditions that were designed to elicit the yawning response.
Saliva samples were collected at the start and after yawning, or at the
end of the presentation of yawning-provoking stimuli, in the absence
of a yawn, and EMG data was additionally collected during rest and
yawning phases. Hospital Anxiety and Depression Scale, Yawning
Susceptibility Scale, General Health Questionnaire, demographic,
and health details were collected and the following exclusion criteria
were adopted: chronic fatigue, diabetes, fibromyalgia, heart
condition, high blood pressure, hormone replacement therapy,
multiple sclerosis, and stroke. Significant differences were found
between the saliva cortisol samples for the yawners, t (23) = -4.263, p
= 0.000, as compared with the non-yawners between rest and poststimuli,
which was non-significant. There were also significant
differences between yawners and non-yawners for the EMG
potentials with the yawners having higher rest and post-yawning
potentials. Significant evidence was found to support the Thompson
Cortisol Hypothesis suggesting that rises in cortisol levels are
associated with the yawning response. Further research is underway
to explore the use of cortisol as a potential diagnostic tool as an assist
to the early diagnosis of symptoms related to neurological disorders.
Bournemouth University Research & Ethics approval granted:
JC28/1/13-KA6/9/13. Professional code of conduct, confidentiality,
and safety issues have been addressed and approved in the Ethics
submission. Trials identification number: ISRCTN61942768.
http://www.controlled-trials.com/isrctn/
Abstract: This paper describes a subarray based low
computational design method of multiuser massive multiple
input multiple output (MIMO) system. In our previous works, use of
large array is assumed only in transmitter, but this study considers
the case both of transmitter and receiver sides are equipped with
large array antennas. For this aim, receive arrays are also divided
into several subarrays, and the former proposed method is modified
for the synthesis of a large array from subarrays in both ends.
Through computer simulations, it is verified that the performance
of the proposed method is degraded compared with the original
approach, but it can achieve the improvement in the aspect of
complexity, namely, significant reduction of the computational load
to the practical level.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: Evaluation of the excavation-induced ground
movements is an important design aspect of support systems in urban
areas. Geological and geotechnical conditions of an excavation area
have significant effects on excavation-induced ground movements and
the related damage. This paper is aimed at studying the performance of
excavation walls supported by nails in jointed rock medium. The
performance of nailed walls is investigated based on evaluating the
excavation-induced ground movements. For this purpose, a set of
calibrated 2D finite element models are developed by taking into
account the nail-rock-structure interactions, the anisotropic properties
of jointed rock, and the staged construction process. The results of this
paper highlight effects of different parameters such as joint
inclinations, anisotropy of rocks and nail inclinations on deformation
parameters of excavation wall supported by nails.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: This paper aims to determine Fundamental Natural
Frequency (FNF) of a structural composite floor system known as
Chromite. To achieve this purpose, FNFs of studied panels are
determined by development of Finite Element Models (FEMs) in
ABAQUS program. American Institute of Steel Construction (AISC)
code in Steel Design Guide Series 11 presents a fundamental formula
to calculate FNF of a steel framed floor system. This formula has
been used to verify results of the FEMs. The variability in the FNF of
the studied system under various parameters such as dimensions of
floor, boundary conditions, rigidity of main and secondary beams
around the floor, thickness of concrete slab, height of composite
joists, distance between composite joists, thickness of top and bottom
flanges of the open web steel joists, and adding tie beam
perpendicular on the composite joists, is determined. The results
show that changing in dimensions of the system, its boundary
conditions, rigidity of main beam, and also adding tie beam,
significant changes the FNF of the system up to 452.9%, 50.8%, -
52.2%, %52.6%, respectively. In addition, increasing thickness of
concrete slab increases the FNF of the system up to 10.8%.
Furthermore, the results demonstrate that variation in rigidity of
secondary beam, height of composite joist, and distance between
composite joists, and thickness of top and bottom flanges of open
web steel joists insignificant changes the FNF of the studied system
up to -0.02%, -3%, -6.1%, and 0.96%, respectively. Finally, the
results of this study help designer predict occurrence of resonance,
comfortableness, and design criteria of the studied system.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: Asphalt concrete pavements have a short life cycle,
failing mainly due to temperature changes, traffic loading and ageing.
Modified asphalt mixtures provide the technology to produce a
bituminous binder with improved viscoelastic properties, which
remain in balance over a wider temperature range and loading
conditions. In this research, 60/70 penetration grade asphalt binder
was modified by adding 2, 4, 6, 8 and 10 percent by weight of asphalt
binder following the wet process and the mineral aggregate was
modified by adding 1, 2, 3, 4 and 5 percent crumb rubber by volume
of the mineral aggregate following the dry process. The LDPE
modified asphalt binder rheological properties were evaluated. The
laboratory results showed an increase in viscosity, softening point
and stiffness of the binder. The modified asphalt was then used in
preparing asphalt mixtures by Marshall Mix design procedure. The
Marshall Stability values for mixes containing 2% crumb rubber and
4% LDPE were found to be 30% higher than the conventional asphalt
concrete mix.
Abstract: In this paper, we describe the use of formal methods
to model malware behaviour. The modelling of harmful behaviour
rests upon syntactic structures that represent malicious procedures
inside malware. The malicious activities are modelled by a formal
grammar, where API calls’ components are the terminals and the set
of API calls used in combination to achieve a goal are designated
non-terminals. The combination of different non-terminals in various
ways and tiers make up the attack vectors that are used by harmful
software. Based on these syntactic structures a parser can be
generated which takes execution traces as input for pattern
recognition.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: This paper describes a sliding mode controller for
autonomous underwater vehicles (AUVs). The dynamic of AUV
model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
To address these difficulties, a nonlinear sliding mode controller is
designed to approximate the nonlinear dynamics of AUV and
improve trajectory tracking. Moreover, the proposed controller can
profoundly attenuate the effects of uncertainties and external
disturbances in the closed-loop system. Using the Lyapunov theory
the boundedness of AUV tracking errors and the stability of the
proposed control system are also guaranteed. Numerical simulation
studies of an AUV are included to illustrate the effectiveness of the
presented approach.
Abstract: The main issue in designing a wireless sensor network
(WSN) is the finding of a proper routing protocol that complies with
the several requirements of high reliability, short latency, scalability,
low power consumption, and many others. This paper proposes a
novel routing algorithm that complies with these design
requirements. The new routing protocol divides the WSN into several subnetworks
and each sub-network is divided into several clusters. This
division is designed to reduce the number of radio transmission and
hence decreases the power consumption. The network division may
be changed dynamically to adapt with the network changes and
allows the realization of the design requirements.
Abstract: The shielding ability of a shielding cavity with an
aperture will be greatly degraded at resonance frequencies, and the
resonance modes and frequencies are affected by aperture resonances
and aperture-cavity coupling, which are closely related with aperture
sizes. The equivalent circuit method and numerical method of
Transmission Line Matrix (TLM) are used to analyze the effects of
aperture resonances and aperture-cavity coupling on the
electromagnetic resonances of a cavity with an aperture in this paper.
Both analytical and numerical results show that the resonance modes
of a shielding cavity with an aperture consist of cavity resonance
modes and aperture resonance modes, and the resonance frequencies
will shift with the change of the aperture sizes because of the aperture
resonances and aperture-cavity coupling. Variation rules of
electromagnetic resonances with aperture sizes for a cavity with an
aperture are given, which will be useful for design of shielding
cavities.
Abstract: This paper describes I²C Slave implementation using
I²C master obtained from the OpenCores website. This website
provides free Verilog and VHDL Codes to users. The design
implementation for the I²C slave is in Verilog Language and uses
EDA tools for ASIC design known as ModelSim from Mentor
Graphic. This tool is used for simulation and verification purposes.
Common application for this I²C Master-Slave integration is also
included. This paper also addresses the advantages and limitations of
the said design.
Abstract: Operation enhancement in an air cooler depends on
rate of heat transfer, and pressure drop. In this paper for a given heat
duty, study of the effects of FPI (Fin Per Inch) and fin type (circular
and hexagonal fins) on heat transfer, and pressure drop in an air
cooler in Iran, Arvand petrochemical. A program in EES
(Engineering Equations Solver) software moreover, Aspen B-JAC
and HTFS+ softwares are used for this purpose to solve governing
equations. At first the simulated results obtained from this program is
compared to the experimental data for two cases of FPI. The effects
of FPI from 3 to 15 over heat transfer (Q) to pressure drop ratio
(Q/Δp ratio). This ratio is one of the main parameters in design, and
simulation heat exchangers. The results show that heat transfer (Q)
and pressure drop increase with increasing FPI steadily, and the Q/Δp
ratio increases to FPI=12 and then decreased gradually to FPI=15,
and Q/Δp ratio is maximum at FPI=12. The FPI value selection
between 8 and 12 obtained as a result to optimum heat transfer to
pressure drop ratio. Also by contrast, between circular and hexagonal
fins results, the Q/Δp ratio of hexagonal fins more than Q/Δp ratio of
circular fins for FPI between 8 and 12 (optimum FPI)
Abstract: This work explores the inter-region investment
behaviors of Integrated Circuit (IC) design industry from Taiwan to
China using the amount of foreign direct investment (FDI). According
to the mutual dependence among different IC design industrial
locations, Lotka-Volterra model is utilized to explore the FDI
interactions between South and East China. Effects of inter-regional
collaborations on FDI flows into China are considered. The analysis
results show that FDIs into South China for IC design industry
significantly inspire the subsequent FDIs into East China, while FDIs
into East China for Taiwan’s IC design industry significantly hinder
the subsequent FDIs into South China. Because the supply chain along
IC industry includes upstream IC design, midstream manufacturing, as
well as downstream packing and testing enterprises, IC design industry
has to cooperate with IC manufacturing, packaging and testing
industries in the same area to form a strong IC industrial cluster.
Taiwan’s IC design industry implement the largest FDI amount into
East China and the second largest FDI amount into South China
among the four regions: North, East, Mid-West and South China. If IC
design houses undertake more FDIs in South China, those in East
China are urged to incrementally implement more FDIs into East
China to maintain the competitive advantages of the IC supply chain in
East China. On the other hand, as the FDIs in East China rise, the FDIs
in South China will successively decline since capitals have
concentrated in East China. In addition, this investigation proves that
the prediction of Lotka-Volterra model in FDI trends is accurate
because the industrial interactions between the two regions are
included. Finally, this work confirms that the FDI flows cannot reach a
stable equilibrium point, so the FDI inflows into East and South China
will expand in the future.