Abstract: High power laser – total emissivity method (HPL-TE method) for determination of coatings relative total emissivity dependent on the temperature is introduced. Method principle, experimental and evaluation parts of the method are described. Computer model of HPL-TE method is employed to perform the sensitivity analysis of the effect of method parameters on the sample surface temperature in the positions where the surface temperature and radiation heat flux are measured.
Abstract: This work describes a CACSD tool for automatic design of robust controllers for hydraulic turbines. The tool calculates the optimal controller using the MATLAB hinfopt function and it
serves as a practical and effective solution for the laborious task of
designing a different controller for each type of turbine and generator, and different parameters and conditions of the plant. Results of the simulation of a generating unit subject to parameters
variation show the accuracy and efficiency of the obtained robust
controllers.
Abstract: Adapting various sensor devices to communicate
within sensor networks empowers us by providing range of
possibilities. The sensors in sensor networks need to know their
measurable belief of trust for efficient and safe communication. In this
paper, we suggested a trust model using fuzzy logic in sensor network.
Trust is an aggregation of consensus given a set of past interaction
among sensors. We applied our suggested model to sensor networks in
order to show how trust mechanisms are involved in communicating
algorithm to choose the proper path from source to destination.
Abstract: The economic and stable operation was affected
seriously by coal quality disturbance for power plants. Based on model
analysis, influence of the disturbance can be considered as gain change
of control system. Power capability coefficient of coal was
constructed to inhibit it. Accuracy of the coefficient was verified by
operating data. Then coal quality disturbance free system based on
gain scheduling was designed for coordinated control system.
Simulation showed that, the strategy improved control quality
obviously, and inhibited the coal quality disturbance.
Abstract: The concerns about clean environment and high oil
prices driving forces for the research on alternative fuels. The
research efforts directed towards improving the performance of C.I
engines using vegetable oil as fuel. The paper deals results of
performance of a four stroke, single cylinder C.I. engine by preheated
neat Karanja oil is done from 30
o
C to 100
o
C. The performance of the
engine was studied for a speed range between 1500 to 4000 rpm, with
the engine operated under full load conditions. The performance
parameters considered for comparing are brake specific fuel
consumption, thermal efficiency, brake power, Nox emission of the
engine. The engine offers lower thermal efficiency when it is
powered by preheated neat Karanja oil at higher speed. The power
developed and Nox emission increase with the increase in the fuel
inlet temperature and the specific fuel consumption is higher than
diesel fuel operation at all elevated fuel inlet temperature.
Abstract: For a quick and accurate calculation of spatial neutron
distribution in nuclear power reactors 3D nodal codes are usually
used aiming at solving the neutron diffusion equation for a given
reactor core geometry and material composition. These codes use a
second order polynomial to represent the transverse leakage term. In
this work, a nodal method based on the well known nodal expansion
method (NEM), developed at COPPE, making use of this polynomial
expansion was modified to treat the transverse leakage term for the
external surfaces of peripheral reflector nodes.
The proposed method was implemented into a computational
system which, besides solving the diffusion equation, also solves the
burnup equations governing the gradual changes in material
compositions of the core due to fuel depletion. Results confirm the
effectiveness of this modified treatment of peripheral nodes for
practical purposes in PWR reactors.
Abstract: Linear convolutive filters are fast in calculation and in application, and thus, often used for real-time processing of continuous data streams. In the case of transient signals, a filter has not only to detect the presence of a specific waveform, but to estimate its arrival time as well. In this study, a measure is presented which indicates the performance of detectors in achieving both of these tasks simultaneously. Furthermore, a new sub-class of linear filters within the class of filters which minimize the quadratic response is proposed. The proposed filters are more flexible than the existing ones, like the adaptive matched filter or the minimum power distortionless response beamformer, and prove to be superior with respect to that measure in certain settings. Simulations of a real-time scenario confirm the advantage of these filters as well as the usefulness of the performance measure.
Abstract: FACTS devices are used to control the power flow, to
increase the transmission capacity and to optimize the stability of the
power system. One of the most widely used FACTS devices is
Unified Power Flow Controller (UPFC). The controller used in the
control mechanism has a significantly effects on controlling of the
power flow and enhancing the system stability of UPFC. According
to this, the capability of UPFC is observed by using different control
mechanisms based on P, PI, PID and fuzzy logic controllers (FLC) in
this study. FLC was developed by taking consideration of Takagi-
Sugeno inference system in the decision process and Sugeno-s
weighted average method in the defuzzification process. Case studies
with different operating conditions are applied to prove the ability of
UPFC on controlling the power flow and the effectiveness of
controllers on the performance of UPFC. PSCAD/EMTDC program
is used to create the FLC and to simulate UPFC model.
Abstract: Worldwide conventional resources of fossil fuel are depleting very fast due to large scale increase in use of transport vehicles every year, therefore consumption rate of oil in transport sector alone has gone very high. In view of this, the major thrust has now been laid upon the search of alternative energy source and also for cost effective energy conversion system. The air converted into compressed form by non conventional or conventional methods can be utilized as potential working fluid for producing shaft work in the air turbine and thus offering the capability of being a zero pollution energy source. This paper deals with the mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine. Effect of expansion action and steady flow work in the air turbine at high admission air pressure of 6 bar, for varying injection to vane angles ratios 0.2-1.6, at the interval of 0.2 and at different vane angles such as 30o, 45o, 51.4o, 60o, 72o, 90o, and 120o for 12, 8, 7, 6, 5, 4 and 3 vanes respectively at speed of rotation 2500 rpm, has been quantified and analyzed here. Study shows that the expansion power has major contribution to total power, whereas the contribution of flow work output has been found varying only up to 19.4%. It is also concluded that for variation of injection to vane angle ratios from 0.2 to 1.2, the optimal power output is seen at vane angle 90o (4 vanes) and for 1.4 to 1.6 ratios, the optimal total power is observed at vane angle 72o (5 vanes). Thus in the vaned type novel air turbine the optimum shaft power output is developed when rotor contains 4-5 vanes for almost all situations of injection to vane angle ratios from 0.2 to 1.6.
Abstract: This paper focuses on the integration of hybrid renewable energy resources available in remote isolated islands of Sundarban-24 Parganas-South of Eastern part of India to National Grid of conventional power supply to give a Smart-Grid scenario. Before grid-integration, feasibility of optimization of hybrid renewable energy system is monitored through an Intelligent Controller proposed to be installed at Moushuni Island of Sundarban. The objective is to ensure the reliability and efficiency of the system to optimize the utilization of the hybrid renewable energy sources and also a proposition of how theses isolated Hybrid Renewable Energy Systems at remote islands can be grid-connected is analyzed towards vision of green smart-grid.
Abstract: The present report describes the characteristics of
damages and behavior of reinforced concrete buildings during the
tsunami action. The discussion is based on the field damage survey in
selected cities located on the coast of the zone affected by the Great
East Japan Earthquake on March 11, 2011. This earthquake is the most
powerful know earthquake that has hit Japan with a magnitude 9.0 and
with epicenter located at 129 km of Sendai city (off the coast). The
earthquake triggered a destructive tsunami with run up height of up to
40 meters that mainly affect cities located on the Pacific Ocean coast of
the Tohoku region (north-east region of Japan). Reinforced concrete
buildings in general resist the tsunami without collapse however the
non-structural elements like panels and ceilings were severely
damaged. The analysis of damages has permitted to understand the
behavior of RC buildings under tsunami attack, and has also permitted
to establish recommendations for their use to take refuge from tsunami
in places where natural topography makes impossible to reach hilltops
or other safer places.
Abstract: This paper describes interconnection between
technical and economical making decision. The reason of this dealing
could be different: poor technical condition, change of substation
(electrical network) regime, power transformer owner budget deficit
and increasing of tariff on electricity. Establishing of recommended
practice as well as to give general advice and guidance in economical
sector, testing, diagnostic power transformers to establish its
conditions, identify problems and provide potential remedies.
Abstract: The use of Quantum dots is a promising emerging
Technology for implementing digital system at the nano level. It is
effecient for attractive features such as faster speed , smaller size and
low power consumption than transistor technology. In this paper,
various Combinational and sequential logical structures - HALF
ADDER, SR Latch and Flip-Flop, D Flip-Flop preceding NAND,
NOR, XOR,XNOR are discussed based on QCA design, with
comparatively less number of cells and area. By applying these
layouts, the hardware requirements for a QCA design can be reduced.
These structures are designed and simulated using QCA Designer
Tool. By taking full advantage of the unique features of this
technology, we are able to create complete circuits on a single layer
of QCA. Such Devices are expected to function with ultra low
power Consumption and very high speeds.
Abstract: Culture and family structure provide a sense security.
Further, the chrono, macro and micro contexts of development
influence developmental transitions and timetable particularly owing
to variations in the macrosystem associated with non normative life
events like migration. Migration threatens family links, security and
attachment bonds. Rising migratory trends have prompted an
increased interest in migration consequences on familial bonds,
developmental autonomy, socialization process, and sense of
security. This paper takes a narrative approach and applies the
attachment paradigm from a lifespan perspective, to examine the
settlement experiences of an India-born migrant student in Sydney,
Australia. It focuses on her quest to preserve family ties; her remote
secure base; her continual struggle to balance dependency and
autonomy, a major developmental milestone. As positional parental
power is culturally more potent in the Indian society, the paper
therefore raises some important concerns related to cultural
expectations, adaptation, acculturative stress and sense of security.
Abstract: Design Patterns have gained more and more
acceptances since their emerging in software development world last
decade and become another de facto standard of essential knowledge
for Object-Oriented Programming developers nowadays.
Their target usage, from the beginning, was for regular computers,
so, minimizing power consumption had never been a concern.
However, in this decade, demands of more complicated software for
running on mobile devices has grown rapidly as the much higher
performance portable gadgets have been supplied to the market
continuously. To get along with time to market that is business
reason, the section of software development for power conscious,
battery, devices has shifted itself from using specific low-level
languages to higher level ones. Currently, complicated software
running on mobile devices are often developed by high level
languages those support OOP concepts. These cause the trend of
embracing Design Patterns to mobile world.
However, using Design Patterns directly in software development
for power conscious systems is not recommended because they were
not originally designed for such environment. This paper
demonstrates the adapted Design Pattern for power limitation system.
Because there are numerous original design patterns, it is not possible
to mention the whole at once. So, this paper focuses only in creating
Energy Conscious version of existing regular "Builder Pattern" to be
appropriated for developing low power consumption software.
Abstract: The increasing importance of FlexRay systems in
automotive domain inspires unceasingly relative researches. One
primary issue among researches is to verify the reliability of FlexRay
systems either from protocol aspect or from system design aspect.
However, research rarely discusses the effect of network topology on
the system reliability. In this paper, we will illustrate how to model
the reliability of FlexRay systems with various network topologies by
a well-known probabilistic reasoning technology, Bayesian Network.
In this illustration, we especially investigate the effectiveness of error
containment built in star topology and fault-tolerant midpoint
synchronization algorithm adopted in FlexRay communication
protocol. Through a FlexRay steer-by-wire case study, the influence
of different topologies on the failure probability of the FlexRay steerby-
wire system is demonstrated. The notable value of this research is
to show that the Bayesian Network inference is a powerful and
feasible method for the reliability assessment of FlexRay systems.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: In recent years, “Bottom-up Planning Approach" has been widely accepted and expanded from planning theorists. Citizen participation becomes more important in decision-making in informal settlements. Many of previous projects and strategies due to ignorance of citizen participation, have been failed facing with informal settlements and in some cases lead physical expansion of these neighbourhoods. According to recent experiences, the new participatory approach was in somehow successful. This paper focuses on local experiences in Iran. A considerable amount of people live in informal settlements in Iran. With the previous methods, the government could not solve the problems of these settlements. It is time to examine new methods such as empowerment of the local citizens and involve them to solve the current physical, social, and economic problems. The paper aims to address the previous and new strategies facing with informal settlements, the conditions under which citizens could be involved in planning process, limits and potentials of this process, the main actors and issues and finally motivations that are able to promote citizen participation. Documentary studies, observation, interview and questionnaire have been used to achieve the above mentioned objectives. Nearly 80 percent of responder in Saadi Community are ready to participate in regularising their neighbourhoods, if pre-conditions of citizen involvement are being provided. These pre-conditions include kind of problem and its severity, the importance of issue, existence of a short-term solution, etc. Moreover, confirmation of dweller-s ownership can promote the citizen engagement in participatory projects.
Abstract: During signal transmission, the combined effect of the
transmitter filter, the transmission medium, and additive white
Gaussian noise (AWGN) are included in the channel which distort
and add noise to the signal. This causes the well defined signal
constellation to spread causing errors in bit detection. A compact pi
neural network with minimum number of nodes is proposed. The
replacement of summation at each node by multiplication results in
more powerful mapping. The resultant pi network is tested on six
different channels.
Abstract: The noticeable advance in the area of computer technology has paved the way for the invention of powerful mobile devices. However, limited storage, short battery life, and relatively low computational power define the major problems of such devices. Due to the ever increasing computational requirements, such devices may fail to process needed tasks under certain constraints. One of the proposed solutions to this drawback is the introduction of Collaborative Computing, a new concept dealing with the distribution of computational tasks amongst several handhelds. This paper introduces the basics of Collaborative Computing, and proposes a new protocol that aims at managing and optimizing computing tasks in Ad-Hoc Collaborative Computing Environments.