Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: The paper investigates downtrend algorithm and
trading strategy based on chart pattern recognition and technical
analysis in futures market. The proposed chart formation is a pattern
with the lowest low in the middle and one higher low on each side.
The contribution of this paper lies in the reinforcement of statements
about the profitability of momentum trend trading strategies.
Practical benefit of the research is a trading algorithm in falling
markets and back-test analysis in futures markets. When based on
daily data, the algorithm has generated positive results, especially
when the market had downtrend period. Downtrend algorithm can be
applied as a hedge strategy against possible sudden market crashes.
The proposed strategy can be interesting for futures traders, hedge
funds or scientific researchers performing technical or algorithmic
market analysis based on momentum trend trading.
Abstract: In this research, the main aim is to investigate the
antimicrobial effectiveness of ammonyx solutions finishing on
Sweatshirt Sport with immersion method. 60 Male healthy subjects
(football player) participated in this study. They were dressed in a
Sweatshirt for 14 days and some microbes found on them were
investigated. The antimicrobial effect of different ammonyx
solutions(1/100, 1/500, 1/1000, 1/2000 v/v solutions of Ammonyx)
on the identified microbes was studied by the zone inhabitation
method in vitro. In the next step the Sweatshirt Sports were treated
with the same different solutions of ammonyx and the antimicrobial
effectiveness was assessed by colony count method in different times
and the results were compared whit untreated ones. Some mechanical
properties of treated cotton/polyester yarn that used in Sweatshirt
Sport were measured after 30 days and were compared with
untreated one. Finally after finishing, scanning electron microscopy
(SEM) was used to compare the surfaces of the finished and
unfinished specimens. The results showed the presence of five
pathogenic microbes on Sweatshirt Sports such as Escherichia coli,
Staphylococcus aureus, Aspergillus, Mucor and Candida. The
inhalation time for treated on Sweatshirt Sports improved. The
amount of colony growth on treated clothes reduced considerably
and moreover the mechanical tests results showed no significant
deterioration effect of studies properties in comparison to the
untreated yarn. The visual examination of the SEM indicated that the
antimicrobial treatments were applied usefully to fabrics.
Abstract: In this paper, enhanced ground proximity warning simulation and validation system is designed and implemented. First, based on square grid and sub-grid structure, the global digital terrain database is designed and constructed. Terrain data searching is implemented through querying the latitude and longitude bands and separated zones of global terrain database with the current aircraft position. A combination of dynamic scheduling and hierarchical scheduling is adopted to schedule the terrain data, and the terrain data can be read and delete dynamically in the memory. Secondly, according to the scope, distance, approach speed information etc. to the dangerous terrain in front, and using security profiles calculating method, collision threat detection is executed in real-time, and provides caution and warning alarm. According to this scheme, the implementation of the enhanced ground proximity warning simulation system is realized. Simulations are carried out to verify a good real-time in terrain display and alarm trigger, and the results show simulation system is realized correctly, reasonably and stable.
Abstract: Entrepreneurship has become an important and
extensively researched concept in business studies. Research on
foreign direct investment (FDI) has become widespread due to the
growth of FDI and its importance in globalization. Most
entrepreneurship studies examined the importance and influence of
entrepreneurial orientation in a micro-level context. On the other
hand, studies and research concerning FDI used statistical techniques
to analyze the effect, determinants, and motives of FDI on a
macroeconomic level, ignoring empirical studies on other noneconomic
determinants. In order to bridge the gap between the theory
and empirical evidence on FDI and the theory and research on
entrepreneurship, this study examines the impact of entrepreneurship
on inward foreign direct investment. The relationship between
entrepreneurship and foreign direct investment is investigated
through regression analysis of pooled time-series and cross-sectional
data. The results suggest that entrepreneurship has a significant effect
on FDI.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: WiMAX is defined as Worldwide Interoperability for
Microwave Access by the WiMAX Forum, formed in June 2001 to
promote conformance and interoperability of the IEEE 802.16
standard, officially known as WirelessMAN. The attractive features
of WiMAX technology are very high throughput and Broadband
Wireless Access over a long distance. A detailed simulation
environment is demonstrated with the UGS, nrtPS and ertPS service
classes for throughput, delay and packet delivery ratio for a mixed
environment of fixed and mobile WiMAX. A simple mobility aspect
is considered for the mobile WiMAX and the PMP mode of
transmission is considered in TDD mode. The Network Simulator 2
(NS-2) is the tool which is used to simulate the WiMAX network
scenario. A simple Priority Scheduler and Weighted Round Robin
Schedulers are the WiMAX schedulers used in the research work
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.
Abstract: Pyritisation halos are identified in weathering crusts and unconsolidated formations at five locations within large fault structure of the Urals’ eastern slope. Electron microscopy reveals the presence of inclusions and growths on pyrite faces – normally on cubic pyrite with striations, or combinations of cubes and other forms. Following neogenesis types are established: native elements and intermetallic compounds (including gold and silver), halogenides, sulphides, sulfosalts, tellurides, sulphotellurides,
selenides, tungstates, sulphates, phosphates, carbon-based substances. Direct relationship is noted between amount and diversity of such mineral phases, and proximity to and scale of ore-grade mineralization. Gold and silver, both in native form and within tellurides, presence of lead (galena, native lead), native tungsten, and, possibly, molybdenite and sulfosalts can indicate gold-bearing formations. First find of native tungsten in the Urals is for the first time – in crystallised and druse-like form. Link is suggested between unusual mineralization and “reducing” hydrothermal fluids from deep-seated faults at later stages of Urals’ reactivation.
Abstract: This study reports results of a meta-analytic path analysis e-learning Acceptance Model with k = 27 studies, Databases searched included Information Sciences Institute (ISI) website. Variables recorded included perceived usefulness, perceived ease of use, attitude toward behavior, and behavioral intention to use e-learning. A correlation matrix of these variables was derived from meta-analytic data and then analyzed by using structural path analysis to test the fitness of the e-learning acceptance model to the observed aggregated data. Results showed the revised hypothesized model to be a reasonable, good fit to aggregated data. Furthermore, discussions and implications are given in this article.
Abstract: The following study aims to outline, whether the
perceptions of entrepreneurs about their entrepreneurial activities and
the underlying meanings of their activities are universal or whether
they vary systematically across cultures. In contrast to previous
studies, the phenomenographical approach and the resulting findings
of this study provide new insights into what constitutes
entrepreneurship by drawing an inference from the perceptions of
entrepreneurs in the United States and in Germany. Culture is shown
to have an important impact on entrepreneurship, since the
underlying meanings of entrepreneurship vary significantly among
the two sample groups. Furthermore, the study sheds more light on
the culturally contingent 'why' of entrepreneurship by looking at the
internal motivations of individuals instead of exclusively focusing on
character traits or external influences of the respective economic
environments.
Abstract: The purpose of the study was to find out the efficacy
of selected mobility exercises and participation in special games on psychomotor abilities, functional abilities and skill performance
among intellectually disabled children of age group under 14. Thirty male students who were studying in Balar Kalvi Nilayam and YMCA
College Special School, Chennai, acted as subjects for the study.
They were only mild and moderate in intellectual disability. These
students did not undergo any special training or coaching programme apart from their regular routine physical activity classes as a part of
the curriculum in the school. They were attached at random, based on
age in which 30 belonged to under 14 age group, which was divided
into three equal group of ten for each experimental treatment. 10
students (Treatment group I) underwent calisthenics and special
games participation, 10 students (Treatment group II) underwent
aquatics and special games participation, 10 students (Treatment
group III) underwent yoga and special games participation. The subjects were tested on selected criterion variables prior (pre test)
and after twelve weeks of training (post test). The pre and post test
data collected from three groups on functional abilities(self care,
learning, capacity for independent living), psychomotor
variables(static balance, eye hand coordination, simple reaction time
test) and skill performance (bocce skill, badminton skill, table tennis
skill) were statistically examined for significant difference, by
applying the analysis ANACOVA. Whenever an 'F' ratio for
adjusted test was found to be significant for adjusted post test means,
Scheffe-s test was followed as a post-hoc test to determine which of
the paired mean differences was significant. The result of the study
showed that among under 14 age groups there was a significant improvement on selected criterion variables such as, Balance,
Coordination, self-care and learning and also in Bocce, Badminton & Table Tennis skill performance, due to mobility exercises and
participation in special games. However there were no significant
differences among the groups.
Abstract: This paper discusses the implementation of the Kalman
Filter along with the Global Positioning System (GPS) for indoor
robot navigation. Two dimensional coordinates is used for the map
building, and refers to the global coordinate which is attached to the
reference landmark for position and direction information the robot
gets. The Discrete Kalman Filter is used to estimate the robot position,
project the estimated current state ahead in time through time update
and adjust the projected estimated state by an actual measurement at
that time via the measurement update. The navigation test has been
performed and has been found to be robust.
Abstract: Appeared toward 1986, the object-oriented databases
management systems had not known successes knew five years after
their birth. One of the major difficulties is the query optimization.
We propose in this paper a new approach that permits to enrich
techniques of query optimization existing in the object-oriented
databases. Seen success that knew the query optimization in the
relational model, our approach inspires itself of these optimization
techniques and enriched it so that they can support the new concepts
introduced by the object databases.
Abstract: This paper addresses control of commutation of switched reluctance (SR) motor without the use of a physical position detector. Rotor position detection schemes for SR motor based on magnetisation characteristics of the motor use normal excitation or applied current /voltage pulses. The resulting schemes are referred to as passive or active methods respectively. The research effort is in realizing an economical sensorless SR rotor position detector that is accurate, reliable and robust to suit a particular application. An effective and reliable means of generating commutation signals of an SR motor based on inductance profile of its stator windings determined using active probing technique is presented. The scheme has been validated online using a 4-phase 8/6 SR motor and an 8-bit processor.
Abstract: One very interesting field of research in Pattern Recognition that has gained much attention in recent times is Gesture Recognition. In this paper, we consider a form of dynamic hand gestures that are characterized by total movement of the hand (arm) in space. For these types of gestures, the shape of the hand (palm) during gesturing does not bear any significance. In our work, we propose a model-based method for tracking hand motion in space, thereby estimating the hand motion trajectory. We employ the dynamic time warping (DTW) algorithm for time alignment and normalization of spatio-temporal variations that exist among samples belonging to the same gesture class. During training, one template trajectory and one prototype feature vector are generated for every gesture class. Features used in our work include some static and dynamic motion trajectory features. Recognition is accomplished in two stages. In the first stage, all unlikely gesture classes are eliminated by comparing the input gesture trajectory to all the template trajectories. In the next stage, feature vector extracted from the input gesture is compared to all the class prototype feature vectors using a distance classifier. Experimental results demonstrate that our proposed trajectory estimator and classifier is suitable for Human Computer Interaction (HCI) platform.
Abstract: In the self-stabilizing algorithmic paradigm, each node has a local view of the system, in a finite amount of time the system converges to a global state with desired property. In a graph G =
(V, E), a subset S C V is a 2-packing if Vi c V: IN[i] n SI
Abstract: This work investigated the steady state and dynamic
simulation of a fixed bed industrial naphtha reforming reactors. The
performance of the reactor was investigated using a heterogeneous
model. For process simulation, the differential equations are solved
using the 4th order Runge-Kutta method .The models were validated
against measured process data of an existing naphtha reforming plant.
The results of simulation in terms of components yields and
temperature of the outlet were in good agreement with empirical data.
The simple model displays a useful tool for dynamic simulation,
optimization and control of naphtha reforming.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: Classification is an interesting problem in functional
data analysis (FDA), because many science and application problems
end up with classification problems, such as recognition, prediction,
control, decision making, management, etc. As the high dimension
and high correlation in functional data (FD), it is a key problem to
extract features from FD whereas keeping its global characters, which
relates to the classification efficiency and precision to heavens. In this
paper, a novel automatic method which combined Genetic Algorithm
(GA) and classification algorithm to extract classification features is
proposed. In this method, the optimal features and classification model
are approached via evolutional study step by step. It is proved by
theory analysis and experiment test that this method has advantages in
improving classification efficiency, precision and robustness whereas
using less features and the dimension of extracted classification
features can be controlled.