Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: Breast motion and discomfort has been studied in
Australia, Britain and the United States, while little information was
known about the breast motion conditions of Chinese women. The aim
of this paper was to study the breast motion and discomfort of Chinese
women in no bra condition, daily bra condition and sports bra
condition. Breast motion and discomfort of 8 participants was assessed
during walking at 5km h-1 and running at 10km h-1. Statistical methods
were used to analyze the difference and relationship between breast
displacement, perceived breast motion and breast discomfort. Three
indexes were developed to evaluate the functions of bras on reducing
objective breast motion, subjective breast motion and breast
discomfort. The result showed that breast motion of Chinese women
was smaller than previous research, which may be resulted from
smaller breast size in Asian women.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: This paper presents the study of parameters affecting
the environment protection in the printing industry. The paper has
also compared LCA studies performed within the printing industry in
order to identify common practices, limitations, areas for
improvement, and opportunities for standardization. This comparison
is focused on the data sources and methodologies used in the printing
pollutants register. The presented concepts, methodology and results
represent the contribution to the sustainable development
management. Furthermore, the paper analyzes the result of the
quantitative identification of hazardous substances emitted in printing
industry of Novi Sad.
Abstract: In current common research reports, salient regions
are usually defined as those regions that could present the main
meaningful or semantic contents. However, there are no uniform
saliency metrics that could describe the saliency of implicit image
regions. Most common metrics take those regions as salient regions,
which have many abrupt changes or some unpredictable
characteristics. But, this metric will fail to detect those salient useful
regions with flat textures. In fact, according to human semantic
perceptions, color and texture distinctions are the main characteristics
that could distinct different regions. Thus, we present a novel saliency
metric coupled with color and texture features, and its corresponding
salient region extraction methods. In order to evaluate the
corresponding saliency values of implicit regions in one image, three
main colors and multi-resolution Gabor features are respectively used
for color and texture features. For each region, its saliency value is
actually to evaluate the total sum of its Euclidean distances for other
regions in the color and texture spaces. A special synthesized image
and several practical images with main salient regions are used to
evaluate the performance of the proposed saliency metric and other
several common metrics, i.e., scale saliency, wavelet transform
modulus maxima point density, and important index based metrics.
Experiment results verified that the proposed saliency metric could
achieve more robust performance than those common saliency
metrics.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: The paper considers a single-server queue with fixedsize
batch Poisson arrivals and exponential service times, a model
that is useful for a buffer that accepts messages arriving as fixed size
batches of packets and releases them one packet at time. Transient
performance measures for queues have long been recognized as
being complementary to the steady-state analysis. The focus of the
paper is on the use of the functions that arise in the analysis of the
transient behaviour of the queuing system. The paper exploits
practical modelling to obtain a solution to the integral equation
encountered in the analysis. Results obtained indicate that under
heavy load conditions, there is significant disparity in the statistics
between the transient and steady state values.
Abstract: The epoxidation of soybean oil at temperature of 600C
was provided the best result in terms of attaching the –OH
functionality. Temperatures below and above 600C it is likely the
attaching reaction did not proceed sufficiently fast. The considerable
yield below 40%, implies the oil is not completely converted, it is not
possible by conventional methods, because the epoxide decomposes
at the temperature required. The objective of this work was the
development of catalyst toward the conversion of epoxide and polyol
with reaction temperature at 50,60, and 700C. The effect of different
type of catalyst were studied, the effect of alcohols with different
molecular configuration was determined which leads to selective
addition of alcohols to the epoxide oils.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.
Abstract: The segmentation of endovascular tools in fluoroscopy images can be accurately performed automatically or by minimum user intervention, using known modern techniques. It has been proven in literature, but no clinical implementation exists so far because the computational time requirements of such technology have not yet been met. A classical segmentation scheme is composed of edge enhancement filtering, line detection, and segmentation. A new method is presented that consists of a vector that propagates in the image to track an edge as it advances. The filtering is performed progressively in the projected path of the vector, whose orientation allows for oriented edge detection, and a minimal image area is globally filtered. Such an algorithm is rapidly computed and can be implemented in real-time applications. It was tested on medical fluoroscopy images from an endovascular cerebral intervention. Ex- periments showed that the 2D tracking was limited to guidewires without intersection crosspoints, while the 3D implementation was able to cope with such planar difficulties.
Abstract: The use of the oncologic index ISTER allows for a more effective planning of the radiotherapic facilities in the hospitals. Any change in the radiotherapy treatment, due to unexpected stops, may be adapted by recalculating the doses to the new treatment duration while keeping the optimal prognosis. The results obtained in a simulation model on millions of patients allow the definition of optimal success probability algorithms.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: Nowadays, the challenge in hydraulic turbine design is
the multi-objective design of turbine runner to reach higher
efficiency. The hydraulic performance of a turbine is strictly depends
on runner blades shape. The present paper focuses on the application
of the multi-objective optimization algorithm to the design of a small
Francis turbine runner. The optimization exercise focuses on the
efficiency improvement at the best efficiency operating point (BEP)
of the GAMM Francis turbine. A global optimization method based
on artificial neural networks (ANN) and genetic algorithms (GA)
coupled by 3D Navier-Stokes flow solver has been used to improve
the performance of an initial geometry of a Francis runner. The
results show the good ability of optimization algorithm and the final
geometry has better efficiency with initial geometry. The goal was to
optimize the geometry of the blades of GAMM turbine runner which
leads to maximum total efficiency by changing the design parameters
of camber line in at least 5 sections of a blade. The efficiency of the
optimized geometry is improved from 90.7% to 92.5%. Finally,
design parameters and the way of selection have been considered and
discussed.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: Laboratory activities have produced benefits in
student learning. With current drives of new technology resources
and evolving era of education methods, renewal status of learning
and teaching in laboratory methods are in progress, for both learners
and the educators. To enhance learning outcomes in laboratory works
particularly in engineering practices and testing, learning via handson
by instruction may not sufficient. This paper describes and
compares techniques and implementation of traditional (expository)
with open-ended laboratory (problem-based) for two consecutive
cohorts studying environmental laboratory course in civil engineering
program. The transition of traditional to problem-based findings and
effect were investigated in terms of course assessment student
feedback survey, course outcome learning measurement and student
performance grades. It was proved that students have demonstrated
better performance in their grades and 12% increase in the course
outcome (CO) in problem-based open-ended laboratory style than
traditional method; although in perception, students has responded
less favorable in their feedback.
Abstract: The growing influence of service industries has
prompted greater attention being paid to service operations
management. However, service managers often have difficulty
articulating the veritable effects of their service innovation. Especially,
the performance evaluation process of service innovation problems
generally involves uncertain and imprecise data. This paper presents a
2-tuple fuzzy linguistic computing approach to dealing with
heterogeneous information and information loss problems while the
processes of subjective evaluation integration. The proposed method
based on group decision-making scenario to assist business managers
in measuring performance of service innovation manipulates the
heterogeneity integration processes and avoids the information loss
effectively.
Abstract: The paper is devoted to stochastic analysis of finite
dimensional difference equation with dependent on ergodic Markov
chain increments, which are proportional to small parameter ". A
point-form solution of this difference equation may be represented
as vertexes of a time-dependent continuous broken line given on the
segment [0,1] with "-dependent scaling of intervals between vertexes.
Tending " to zero one may apply stochastic averaging and diffusion
approximation procedures and construct continuous approximation of
the initial stochastic iterations as an ordinary or stochastic Ito differential
equation. The paper proves that for sufficiently small " these
equations may be successfully applied not only to approximate finite
number of iterations but also for asymptotic analysis of iterations,
when number of iterations tends to infinity.
Abstract: This paper employs a new approach to regulate the
blood glucose level of type I diabetic patient under an intensive
insulin treatment. The closed-loop control scheme incorporates
expert knowledge about treatment by using reinforcement learning
theory to maintain the normoglycemic average of 80 mg/dl and the
normal condition for free plasma insulin concentration in severe
initial state. The insulin delivery rate is obtained off-line by using Qlearning
algorithm, without requiring an explicit model of the
environment dynamics. The implementation of the insulin delivery
rate, therefore, requires simple function evaluation and minimal
online computations. Controller performance is assessed in terms of
its ability to reject the effect of meal disturbance and to overcome the
variability in the glucose-insulin dynamics from patient to patient.
Computer simulations are used to evaluate the effectiveness of the
proposed technique and to show its superiority in controlling
hyperglycemia over other existing algorithms