Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: The current study begins with an awareness that
today-s media environment is characterized by technological
development and a new way of reading caused by the introduction of
the Internet. The researcher conducted a meta analysis framed within
Technological Determinism to investigate the process of hypertext
reading, its differences from linear reading and the effects such
differences can have on people-s ways of mentally structuring their
world. The relationship between literacy and the comprehension
achieved by reading hypertexts is also investigated. The results show
hypertexts are not always user friendly. People experience hyperlinks
as interruptions that distract their attention generating comprehension
and disorientation. On one hand hypertextual jumping reading
generates interruptions that finally make people lose their
concentration. On the other hand hypertexts fascinate people who
would rather read a document in such a format even though the
outcome is often frustrating and affects their ability to elaborate and
retain information.
Abstract: Medical image modalities such as computed
tomography (CT), magnetic resonance imaging (MRI), ultrasound
(US), X-ray are adapted to diagnose disease. These modalities
provide flexible means of reviewing anatomical cross-sections and
physiological state in different parts of the human body. The raw
medical images have a huge file size and need large storage
requirements. So it should be such a way to reduce the size of those
image files to be valid for telemedicine applications. Thus the image
compression is a key factor to reduce the bit rate for transmission or
storage while maintaining an acceptable reproduction quality, but it is
natural to rise the question of how much an image can be compressed
and still preserve sufficient information for a given clinical
application. Many techniques for achieving data compression have
been introduced. In this study, three different MRI modalities which
are Brain, Spine and Knee have been compressed and reconstructed
using wavelet transform. Subjective and objective evaluation has
been done to investigate the clinical information quality of the
compressed images. For the objective evaluation, the results show
that the PSNR which indicates the quality of the reconstructed image
is ranging from (21.95 dB to 30.80 dB, 27.25 dB to 35.75 dB, and
26.93 dB to 34.93 dB) for Brain, Spine, and Knee respectively. For
the subjective evaluation test, the results show that the compression
ratio of 40:1 was acceptable for brain image, whereas for spine and
knee images 50:1 was acceptable.
Abstract: Sediment and mangrove root samples from Iko River
Estuary, Nigeria were analyzed for microbial and polycyclic
aromatic hydrocarbon (PAH) content. The total heterotrophic
bacterial (THB) count ranged from 1.1x107 to 5.1 x107 cfu/g, total
fungal (TF) count ranged from 1.0x106 to 2.7x106 cfu/g, total
coliform (TC) count ranged from 2.0x104 to 8.0x104cfu/g while
hydrocarbon utilizing bacterial (HUB) count ranged from 1.0x 105 to
5.0 x 105cfu/g. There was a range of positive correlation (r = 0.72 to
0.93) between THB count and total HUB count, respectively. The
organisms were Staphylococcus aureus, Bacillus cereus,
Flavobacterium breve, Pseudomonas aeruginosa, Erwinia
amylovora, Escherichia coli, Enterobacter sp, Desulfovibrio sp,
Acinetobacter iwoffii, Chromobacterium violaceum, Micrococcus
sedentarius, Corynebacterium sp, and Pseudomonas putrefaciens.
The PAH were Naphthalene, 2-Methylnaphthalene, Acenapthylene,
Acenaphthene, Fluorene, Phenanthene, Anthracene, Fluoranthene,
Pyrene, Benzo(a)anthracene, Chrysene, Benzo(b)fluoranthene,
Benzo(k)fluoranthene, Benzo(a)pyrene, Dibenzo(a,h)anthracene,
Benzo(g,h,l)perylene ,Indeno(1,2,3-d)pyrene with individual PAH
concentrations that ranged from 0.20mg/kg to 1.02mg/kg, 0.20mg/kg
to 1.07mg/kg and 0.2mg/kg to 4.43mg/kg in the benthic sediment,
epipellic sediment and mangrove roots, respectively. Total PAH
ranged from 6.30 to 9.93mg/kg, 6.30 to 9.13mg/kg and 9.66 to
16.68mg/kg in the benthic sediment, epipellic sediment and
mangrove roots, respectively. The high concentrations in the
mangrove roots are indicative of bioaccumulation of the pollutant in
the plant tissue. The microorganisms are of ecological significance
and the detectable quantities of polycyclic aromatic hydrocarbon
could be partitioned and accumulated in tissues of infaunal and
epifaunal organisms in the study area.
Abstract: This article presents the evolution and technological changes implemented on the full scale simulators developed by the Simulation Department of the Instituto de Investigaciones Eléctricas1 (Mexican Electric Research Institute) and located at different training centers around the Mexican territory, and allows US to know the last updates, basically from the input/output view point, of the current simulators at some facilities of the electrical sector as well as the compatible industry of the electrical manufactures and industries such as Comision Federal de Electricidad (CFE*, The utility Mexican company). Tendencies of these developments and impact within the operators- scope are also presented.
Abstract: At present, the severe oil crisis and greenhouse effect are booming, which is a growing worry for China. Over a long period of study, choosing the development of biological diesel is a feasible way in the desertification region in China. With considering the adaptability of Micro-algae in desertification region and analyzing energy consumption and carbon calculations of Micro-algae biodiesel produced by JJ company , this paper, make the microalgae our optimal choice to develop biological diesel in china's desertification region.
Abstract: One astonishing capability of humans is to recognize thousands of different objects visually, and to learn the semantic association between those objects and words referring to them. This work is an attempt to build a computational model of such capacity,simulating the process by which infants learn how to recognize objects and words through exposure to visual stimuli and vocal sounds.One of the main fact shaping the brain of a newborn is that lights and colors come from entities of the world. Gradually the visual system learn which light sensations belong to same entities, despite large changes in appearance. This experience is common between humans and several other mammals, like non-human primates. But humans only can recognize a huge variety of objects, most manufactured by himself, and make use of sounds to identify and categorize them. The aim of this model is to reproduce these processes in a biologically plausible way, by reconstructing the essential hierarchy of cortical circuits on the visual and auditory neural paths.
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: In the last 15 years, a number of methods have been proposed for forecasting based on fuzzy time series. Most of the fuzzy time series methods are presented for forecasting of enrollments at the University of Alabama. However, the forecasting accuracy rates of the existing methods are not good enough. In this paper, we compared our proposed new method of fuzzy time series forecasting with existing methods. Our method is based on frequency density based partitioning of the historical enrollment data. The proposed method belongs to the kth order and time-variant methods. The proposed method can get the best forecasting accuracy rate for forecasting enrollments than the existing methods.
Abstract: The effects of seawater and slurry ice bleeding methods on the sensory, microbiological and chemical quality changes of cod fillets during chilled storage were examined in this study. The results from sensory evaluation showed that slurry ice bleeding method prolonged the shelf life of cod fillets up to 13-14 days compared to 10-11 days for fish bled in seawater. Slurry ice bleeding method also led to a slower microbial growth and biochemical developments, resulting lower total plate count (TPC), H2S-producing bacteria count, total volatile basic nitrogen (TVB-N), trimethylamine (TMA), free fatty acid (FFA) content and higher phospholipid content (PL) compared to those of samples bled in seawater. The results of principle component analysis revealed that TPC, H2S-producing bacteria, TVB-N, TMA and FFA were in significant correlation. They were also in negative correlation with sensory evaluation (Torry score), PL and water holding capacity (WHC).
Abstract: Computer modeling has played a unique role in
understanding electrocardiography. Modeling and simulating cardiac
action potential propagation is suitable for studying normal and
pathological cardiac activation. This paper presents a 2-D Cellular
Automata model for simulating action potential propagation in
cardiac tissue. We demonstrate a novel algorithm in order to use
minimum neighbors. This algorithm uses the summation of the
excitability attributes of excited neighboring cells. We try to
eliminate flat edges in the result patterns by inserting probability to
the model. We also preserve the real shape of action potential by
using linear curve fitting of one well known electrophysiological
model.
Abstract: The aim of this contribution is to present a new
approach in modeling the electrical activity of the human heart. A
recurrent artificial neural network is being used in order to exhibit a
subset of the dynamics of the electrical behavior of the human heart.
The proposed model can also be used, when integrated, as a
diagnostic tool of the human heart system.
What makes this approach unique is the fact that every model is
being developed from physiological measurements of an individual.
This kind of approach is very difficult to apply successfully in many
modeling problems, because of the complexity and entropy of the
free variables describing the complex system. Differences between
the modeled variables and the variables of an individual, measured at
specific moments, can be used for diagnostic purposes. The sensor
fusion used in order to optimize the utilization of biomedical sensors
is another point that this paper focuses on. Sensor fusion has been
known for its advantages in applications such as control and
diagnostics of mechanical and chemical processes.
Abstract: The paper considers a novel modular and intrinsically safe redundant robotic system with biologically inspired actuators (pneumatic artificial muscles and rubber bellows actuators). Similarly to the biological systems, the stiffness of the internal parallel modules, representing 2 DOF joints in the serial robotic chains, is controlled by co-activation of opposing redundant actuator groups in the null-space of the module Jacobian, without influencing the actual robot position. The decoupled position/stiffness control allows the realization of variable joint stiffness according to different force-displacement relationships. The variable joint stiffness, as well as limited pneumatic muscle/bellows force ability, ensures internal system safety that is crucial for development of human-friendly robots intended for human-robot collaboration. The initial experiments with the system prototype demonstrate the capabilities of independently, simultaneously controlling both joint (Cartesian) motion and joint stiffness. The paper also presents the possible industrial applications of snake-like robots built using the new modules.
Abstract: In this paper, a robust watermarking algorithm using
the wavelet transform and edge detection is presented. The efficiency
of an image watermarking technique depends on the preservation of
visually significant information. This is attained by embedding the
watermark transparently with the maximum possible strength. The
watermark embedding process is carried over the subband
coefficients that lie on edges, where distortions are less noticeable,
with a subband level dependent strength. Also, the watermark is
embedded to selected coefficients around edges, using a different
scale factor for watermark strength, that are captured by a
morphological dilation operation. The experimental evaluation of the
proposed method shows very good results in terms of robustness and
transparency to various attacks such as median filtering, Gaussian
noise, JPEG compression and geometrical transformations.
Abstract: The influences of pulsed electric fields on early
physiological development in Arabidopsis thaliana were studied.
Inside a 4-mm electroporation cuvette, pre-germination seeds were
subjected to high-intensity, nanosecond electrical pulses generated
using laboratory-assembled pulsed electric field system. The field
strength was varied from 5 to 20 kV.cm-1 and the pulse width and the
pulse number were maintained at 10 ns and 100, respectively,
corresponding to the specific treatment energy from 300 J.kg-1 to 4.5
kJ.kg-1. Statistical analyses on the average leaf area 5 and 15 days
following pulsed electric field treatment showed that the effects
appear significant the second week after treatments with a maximum
increase of 80% compared to the control (P < 0.01).
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.