Abstract: Most often the contaminants are not taken seriously into consideration, and this behavior comes out directly from the lack of monitoring and professional reporting about pollution in the printing facilities in Serbia. The goal of planned and systematic ozone measurements in ambient air of the screen printing facilities in Novi Sad is to examine of its impact on the employees health, and to track trends in concentration. In this study, ozone concentrations were determined by using discontinuous and continuous method during the automatic and manual screen printing process. Obtained results indicates that the average concentrations of ozone measured during the automatic process were almost 3 to 28 times higher for discontinuous and 10 times higher for continuous method (1.028 ppm) compared to the values prescribed by OSHA. In the manual process, average concentrations of ozone were within prescribed values for discontinuous and almost 3 times higher for continuous method (0.299 ppm).
Abstract: Passive systems were born with the purpose of the
greatest exploitation of solar energy in cold climates and high
altitudes. They spread themselves until the 80-s all over the world
without any attention to the specific climate and the summer
behavior; this caused the deactivation of the systems due to a series
of problems connected to the summer overheating, the complex
management and the rising of the dust.
Until today the European regulation limits only the winter
consumptions without any attention to the summer behavior but, the
recent European EN 15251 underlines the relevance of the indoor
comfort, and the necessity of the analytic studies validation by
monitoring case studies.
In the porpose paper we demonstrate that the solar wall is an
efficient system both from thermal comfort and energy saving point
of view and it is the most suitable for our temperate climates because
it can be used as a passive cooling sistem too. In particular the paper
present an experimental and numerical analisys carried out on a case
study with nine different solar passive systems in Ancona, Italy.
We carried out a detailed study of the lodging provided by the
solar wall by the monitoring and the evaluation of the indoor
conditions.
Analyzing the monitored data, on the base of recognized models
of comfort (ISO, ASHRAE, Givoni-s BBCC), is emerged that the
solar wall has an optimal behavior in the middle seasons. In winter
phase this passive system gives more advantages in terms of energy
consumptions than the other systems, because it gives greater heat
gain and therefore smaller consumptions. In summer, when outside
air temperature return in the mean seasonal value, the indoor comfort
is optimal thanks to an efficient transversal ventilation activated from
the same wall.
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. Frameworks
are introduced to reduce the cost of a product line (i.e., a family of
products that shares the common features). Software testing is a timeconsuming
and costly ongoing activity during the application
software development process. Generating reusable test cases for the
framework applications during the framework development stage,
and providing and using the test cases to test part of the framework
application whenever the framework is used reduces the application
development time and cost considerably. This paper introduces the
Framework Interface State Transition Tester (FIST2), a tool for
automated unit testing of Java framework applications. During the
framework development stage, given the formal descriptions of the
framework hooks, the specifications of the methods of the
framework-s extensible classes, and the illegal behavior description
of the Framework Interface Classes (FICs), FIST2 generates unitlevel
test cases for the classes. At the framework application
development stage, given the customized method specifications of
the implemented FICs, FIST2 automates the use, execution, and
evaluation of the already generated test cases to test the implemented
FICs. The paper illustrates the use of the FIST2 tool for testing
several applications that use the SalesPoint framework.
Abstract: In the current study, we have conducted an experimental investigation on the utilization of electronic arc furnace (EAF) reducing slag for the absorption of CO2 via wet grinding method. It was carried out by various grinding conditions. The slag was ground in the vibrating ball mill in the presence of CO2 and pure water under ambient temperature. The reaction behavior was monitored with constant pressure method, and the changes of experimental systems volume as a function of grinding time were measured. It was found that the CO2 absorption occurred as soon as the grinding started. The CO2 absorption was significantly increased in the case of wet grinding compare to the dry grinding. Generally, the amount of CO2 absorption increased as the amount of water, weight of slag and initial pressure increased. However, it was decreased when the amount of water exceeds 200ml and when smaller balls were used. The absorption of CO2 occurred simultaneously with the start of the grinding and it stopped when the grinding was stopped. According to this research, the CO2 reacted with the CaO inside the slag, forming CaCO3.
Abstract: This study aims to examine the factors affecting
knowledge sharing behavior in knowledge-based electronic communities (e-communities) because quantity and quality of
knowledge shared among the members play a critical role in the community-s sustainability. Past research has suggested three
perspectives that may affect the quantity and quality of knowledge
shared: economics, social psychology, and social ecology. In this
study, we strongly believe that an economic perspective may be suitable to validate factors influencing newly registered members-
knowledge contribution at the beginning of relationship development.
Accordingly, this study proposes a model to validate the factors influencing members- knowledge sharing based on Transaction Cost
Theory. By doing so, we may empirically test our hypotheses in various types of e-communities to determine the generalizability of our research models.
Abstract: Online learning with Intelligent Tutoring System (ITS) is becoming very popular where the system models the student-s learning behavior and presents to the student the learning material (content, questions-answers, assignments) accordingly. In today-s distributed computing environment, the tutoring system can take advantage of networking to utilize the model for a student for students from other similar groups. In the present paper we present a methodology where using Case Based Reasoning (CBR), ITS provides student modeling for online learning in a distributed environment with the help of agents. The paper describes the approach, the architecture, and the agent characteristics for such system. This concept can be deployed to develop ITS where the tutor can author and the students can learn locally whereas the ITS can model the students- learning globally in a distributed environment. The advantage of such an approach is that both the learning material (domain knowledge) and student model can be globally distributed thus enhancing the efficiency of ITS with reducing the bandwidth requirement and complexity of the system.
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Development of intelligent assembly cell conception includes new solution kind of how to create structures of automated and flexible assembly system. The current trend of the final product quality increasing is affected by time analysis of the entire manufacturing process. The primary requirement of manufacturing is to produce as many products as soon as possible, at the lowest possible cost, but of course with the highest quality. Such requirements may be satisfied only if all the elements entering and affecting the production cycle are in a fully functional condition. These elements consist of sensory equipment and intelligent control elements that are essential for building intelligent manufacturing systems. Intelligent behavior of the system as the control system will repose on monitoring of important parameters of the system in the real time. Intelligent manufacturing system itself should be a system that can flexibly respond to changes in entering and exiting the process in interaction with the surroundings.
Abstract: This paper proposes a solution to the motion planning
and control problem of car-like mobile robots which is required to
move safely to a designated target in a priori known workspace
cluttered with swarm of boids exhibiting collective emergent
behaviors. A generalized algorithm for target convergence and
swarm avoidance is proposed that will work for any number of
swarms. The control laws proposed in this paper also ensures
practical stability of the system. The effectiveness of the proposed
control laws are demonstrated via computer simulations of an
emergent behavior.
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.
Abstract: Data mining is an extraordinarily demanding field referring to extraction of implicit knowledge and relationships, which are not explicitly stored in databases. A wide variety of methods of data mining have been introduced (classification, characterization, generalization...). Each one of these methods includes more than algorithm. A system of data mining implies different user categories,, which mean that the user-s behavior must be a component of the system. The problem at this level is to know which algorithm of which method to employ for an exploratory end, which one for a decisional end, and how can they collaborate and communicate. Agent paradigm presents a new way of conception and realizing of data mining system. The purpose is to combine different algorithms of data mining to prepare elements for decision-makers, benefiting from the possibilities offered by the multi-agent systems. In this paper the agent framework for data mining is introduced, and its overall architecture and functionality are presented. The validation is made on spatial data. Principal results will be presented.
Abstract: A high performance thin layer chromatography
system (HPTLC) for the separation of vitamin B2 and B12 has been
developed. The separation was successfully using a solvent system of
methanol, water, ammonia 7.3.1 (V/V) as mobile phase on HPTLC
plates impregnated with boric acid. The effect of other mobile phases
on the separation of vitamins was also examined. The method is
based on different behavior of investigated compounds in
impregnated TLC plates with different amount of boric acid. The Rf
values of vitamin B2 and B12 are considered on non impregnated
and impregnated silica gel HPTLC plate with boric acid. The effect
of boric acid in the mobile phase and on HPTLC plates on the RF
values of the vitamins has also been studied.
Abstract: The appearance management behavior of tanning by gay men is examined through the lens of Impression Formation. The study proposes that body image, self-esteem, and internalized homophobia are connected and affect the motives for engaging in sun, salon, and cosmetic tanning. Motives examined were: to look masculine, to look attractive to (potential) partners, to look attractive in general, to socialize, to meet a peer standard, and for personal satisfaction. Using regression analysis to examine data of 103 gay men who engage in at least one method of tanning, results reveal that components of body image and internalized homophobia–but not self-esteem–are linked to various motives and methods of tanning. These findings support and extend the literature of Impression Formation Theory and provide practitioners in the health and healthrelated fields new avenues to pursue when dealing with diseases related to tanning.
Abstract: This paper proposes a method to vibration analysis in
order to on-line monitoring and predictive maintenance during the
milling process. Adapting envelope method to diagnostics and the
analysis for milling tool materials is an important contribution to the
qualitative and quantitative characterization of milling capacity and a
step by modeling the three-dimensional cutting process. An
experimental protocol was designed and developed for the
acquisition, processing and analyzing three-dimensional signal. The
vibration envelope analysis is proposed to detect the cutting capacity
of the tool with the optimization application of cutting parameters.
The research is focused on Hilbert transform optimization to evaluate
the dynamic behavior of the machine/ tool/workpiece.
Abstract: Object: Review recent publications of patient safety
culture to investigate the relationship between leadership behavior,
safety culture, and safety performance in the healthcare industry.
Method: This study is a cross-sectional study, 350 questionnaires were
mailed to hospital workers with 195 valid responses obtained, and a
55.7% valid response rate. Confirmatory factor analysis (CFA) was
carried out to test the factor structure and determine if the composite
reliability was significant with a factor loading of >0.5, resulting in an
acceptable model fit. Results: Through the analysis of One-way
ANOVA, the results showed that physicians significantly have more
negative patient safety culture perceptions and safety performance
perceptions than non- physicians. Conclusions: The path analysis
results show that leadership behavior affects safety culture and safety
performance in the health care industry. Safety performance was
affected and improved with contingency leadership and a positive
patient safety organization culture. The study suggests improving
safety performance by providing a well-managed system that
includes: consideration of leadership, hospital worker training
courses, and a solid safety reporting system.
Abstract: Today the social marketing was constituted as a tool
of significant value in what he refers to the promotion of changes of
behaviors, attitudes end practices. With the objective of analyzing the
benefits that the social marketing can bring for the organizations that
use it the research was of the exploratory and descriptive. In the
present study the comparative method was used, through a qualitative
approach, to analyze the activities developed by three institutions:
the Recovery Center Rosa de Saron, the House of Recovery for
addicts and Teen Challenge Institute Children's Cancer of the
Wasteland (ICIA), kindred of pointing out the benefits of the social
marketing in organizations that don-t seek the profit.
Abstract: Complex systems are composed of several plain interacting independent entities. Interaction between these entities creates a unified behavior at the global level that cannot be predicted by examining the behavior of any single individual component of the system. In this paper we consider a welded frame of an automobile trailer as a real example of Complex Technical Systems, The purpose of this paper is to introduce a Statistical method for predicting the life cycle of complex technical systems. To organize gathering of primary data for modeling the life cycle of complex technical systems an “Automobile Trailer Frame" were used as a prototype in this research. The prototype represents a welded structure of several pieces. Both information flows underwent a computerized analysis and classification for the acquisition of final results to reach final recommendations for improving the trailers structure and their operational conditions.