Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Chatter vibrations and process instabilities are the
most important factors limiting the productivity of the milling
process. Chatter can leads to damage of the tool, the part or the
machine tool. Therefore, the estimation and prediction of the process
stability is very important. The process stability depends on the
spindle speed, the depth of cut and the width of cut. In milling, the
process conditions are defined in the NC-program. While the spindle
speed is directly coded in the NC-program, the depth and width of cut
are unknown. This paper presents a new simulation based approach
for the prediction of the depth and width of cut of a milling process.
The prediction is based on a material removal simulation with an
analytically represented tool shape and a multi-dexel approach for the
workpiece. The new calculation method allows the direct estimation
of the depth and width of cut, which are the influencing parameters of
the process stability, instead of the removed volume as existing
approaches do. The knowledge can be used to predict the stability of
new, unknown parts. Moreover with an additional vibration sensor,
the stability lobe diagram of a milling process can be estimated and
improved based on the estimated depth and width of cut.
Abstract: The Portuguese footwear industry had in the last five years a remarkable performance in the exportation values, the trade balance and others economic indicators. After a long period of difficulties and with a strong reduction of companies and employees since 1994 until 2009, the Portuguese footwear industry changed the strategy and is now a success case between the international players of footwear. Only the Italian industry sells footwear with a higher value than the Portuguese and the distance between them is decreasing year by year. This paper analyses how the Portuguese footwear companies innovate and make innovation, according the classification proposed by the Oslo Manual. Also, analyses the strategy follow in the innovation process and shows the linkage between the type of innovation and the strategy of innovation. The research methodology was qualitative and the strategy for data collection was the case study. The qualitative data will be analyzed with the MAXQDA software. The economic results of the footwear companies studied shows differences between all of them and these differences are related with the innovation strategy adopted. The companies focused in product and marketing innovation, oriented to their target market, have higher ratios “turnover per worker” than the companies focused in process innovation. However, all the footwear companies in this “low-tech” industry create value and contribute to a positive foreign trade of 1.310 million euros in 2013. The growth strategies implemented has the participation of the sectorial organizations in several innovative projects. And it’s obvious that cooperation between all of them is a critical element to the performance achieved by the companies and the innovation observed. The Portuguese footwear sector has in the last years an excellent performance (economic results, exportation values, trade balance, brands and international image) and his performance is strongly related with the strategy in innovation followed, the type of innovation and the networks in the cluster. A simplified model, called “Ace of Diamonds”, is proposed by the authors and explains the way how this performance was reached by the seven companies that participate in the study (two of them are the leaders in the setor), and if this model can be used in others traditional and “low-tech” industries.
Abstract: The Gezi Park protests of 2013 have significantly changed the Turkish agenda and its effects have been felt historically. The protests, which rapidly spread throughout the country, were triggered by the proposal to recreate the Ottoman Army Barracks to function as a shopping mall on Gezi Park located in Istanbul’s Taksim neighbourhood despite the oppositions of several NGOs and when trees were cut in the park for this purpose. Once the news that the construction vehicles entered the park on May 27 spread on social media, activists moved into the park to stop the demolition, against whom the police used disproportioned force. With this police intervention and the then prime-minister Tayyip Erdoğan's insistent statements about the construction plans, the protests turned into anti- government demonstrations, which then spread to the rest of the country, mainly in big cities like Ankara and Izmir. According to the Ministry of Internal Affairs’ June 23rd reports, 2.5 million people joined the demonstrations in 79 provinces, that is all of them, except for the provinces of Bayburt and Bingöl, while even more people shared their opinions via social networks. As a result of these events, 8 civilians and 2 security personnel lost their lives, namely police chief Mustafa Sarı, police officer Ahmet Küçükdağ, citizens Mehmet Ayvalıtaş, Abdullah Cömert, Ethem Sarısülük, Ali İsmail Korkmaz, Ahmet Atakan, Berkin Elvan, Burak Can Karamanoğlu, Mehmet İstif, and Elif Çermik, and 8163 more were injured. Besides being a turning point in Turkish history, the Gezi Park protests also had broad repercussions in both in Turkish and in global media, which focused on Turkey throughout the events. Our study conducts content analysis of three Turkish reporting newspapers with varying ideological standpoints, Hürriyet, Cumhuriyet ve Yeni Şafak, in order to reveal their basic approach to news casting in context of the Gezi Park protests. Headlines, news segments, and news content relating to the Gezi protests were treated and analysed for this purpose. The aim of this study is to understand the social effects of the Gezi Park protests through media samples with varying political attitudes towards news casting.
Abstract: The world crude oil demand is projected to rise to 108.5 million bbl/d by the year 2035. With reserves estimated at 869 billion tonnes worldwide, coal remains an abundant resource. The aim of this work was to produce a high value hydrocarbon liquid product using a Direct Coal Liquefaction (DCL) process at, relatively mild operating conditions. Via hydrogenation, the temperature-staged approach was investigated in a dual reactor lab-scale pilot plant facility. The objectives included maximising thermal dissolution of the coal in the presence of tetralin as the hydrogen donor solvent in the first stage with 2:1 and 3:1 solvent: coal ratios. Subsequently, in the second stage, hydrogen saturation, in particular, hydrodesulphurization (HDS) performance was assessed. Two commercial hydrotreating catalysts were investigated viz. NickelMolybdenum (Ni-Mo) and Cobalt-Molybdenum (Co-Mo). GC-MS results identified 77 compounds and various functional groups present in the first and second stage liquid product. In the first stage 3:1 ratios and liquid product yields catalysed by magnetite were favoured. The second stage product distribution showed an increase in the BTX (Benzene, Toluene, Xylene) quality of the liquid product, branched chain alkanes and a reduction in the sulphur concentration. As an HDS performer and selectivity to the production of long and branched chain alkanes, Ni-Mo had an improved performance over Co-Mo. Co-Mo is selective to a higher concentration of cyclohexane. For 16 days on stream each, Ni-Mo had a higher activity than Co-Mo. The potential to cover the demand for low–sulphur, crude diesel and solvents from the production of high value hydrocarbon liquid in the said process, is thus demonstrated.
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: Public space is essential to strengthen the social and
urban fabric and the social cohesion; there lies the importance of its
study. Hence, the aim of this paper is to analyze the quality of public
space in the XXI century in both quantitative and qualitative terms. In
this article, the concept of public space includes open spaces such as
parks, public squares and walking areas. To make this analysis, we
take Mexico City as the case study. It has a population of nearly 9
million inhabitants and is composed of sixteen boroughs. For this
analysis, we consider both existing public spaces and the government
intervention for building and improving new and existent public
spaces. Results show that on the one hand, quantitatively there is not
an equitable distribution of public spaces due to both the growth of
the city itself as well as due to the absence of political will to create
public spaces. Another factor is the evolution of this city, which has
been growing merely in a “patched pattern”, where public space has
played no role at all with a total absence of urban design. On the
other hand, qualitatively, even the boroughs with the most public
spaces have not shown interest in making these spaces qualitatively
inclusive and open to the general population aiming for integration.
Therefore, urban projects that privatize public space seem to be the
rule, rather than a rehabilitation effort of the existent public spaces.
Hence, state intervention should reinforce its role as an agent of
social change acting in benefit of the majority of the inhabitants with
the promotion of more inclusive public spaces.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: This study identifies factors underlying the digital
divide that is faced by the disabled. The results of its analysis showed
that the digital divide in PC use is affected by age, number of years of
education, employment status, and household income of more than
KRW 3 million. The digital divide in smart device use is affected by
sex, age, number of years of education, time when disability struck,
and household income of more than KRW 3 million. Based on these
results, this study proposes methods for bridging the digital divide
faced by the disabled.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: In light of the technological development and its
introduction into the field of education, an online course was
designed in parallel to the 'conventional' course for teaching the
''Qualitative Research Methods''. This course aimed to characterize
learning-teaching processes in a 'Qualitative Research Methods'
course studied in two different frameworks. Moreover, its objective
was to explore the difference between the culture of a physical
learning environment and that of online learning. The research
monitored four learner groups, a total of 72 students, for two years,
two groups from the two course frameworks each year. The courses
were obligatory for M.Ed. students at an academic college of
education and were given by one female-lecturer. The research was
conducted in the qualitative method as a case study in order to attain
insights about occurrences in the actual contexts and sites in which
they transpire. The research tools were open-ended questionnaire and
reflections in the form of vignettes (meaningful short pictures) to all
students as well as an interview with the lecturer. The tools facilitated
not only triangulation but also collecting data consisting of voices
and pictures of teaching and learning. The most prominent findings
are: differences between the two courses in the change features of the
learning environment culture for the acquisition of contents and
qualitative research tools. They were manifested by teaching
methods, illustration aids, lecturer's profile and students' profile.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Currently, continuous two-phase decanter process
used for olive oil production is the more internationally widespread.
The wastewaters generated from this industry (OMW) are a real
environmental problem because of its high organic load. Among
proposed treatments for these wastewaters, advanced oxidation
technologies (Fenton, ozone, photoFenton, etc.) are the most
favourable. The direct application of these processes is somewhat
expensive. Therefore, the application of a previous stage based on a
flocculation-sedimentation operation is of high importance. In this
research five commercial flocculants (three cationic, and two anionic)
have been used to achieve the separation of phases (liquid clarifiedsludge).
For each flocculant, different concentrations (0-1000 mg/L)
have been studied. In these experiments, sludge volume formed and
the final water quality were determined. The final removal
percentages of total phenols (11.3-25.1%), COD (5.6-20.4%), total
carbon (2.3-26.5%), total organic carbon (1.50-23.8%), total nitrogen
(1.45-24.8%), and turbidity (27.9-61.4%) were determined. The
variation on electric conductivity reduction percentage (1-8%) was
also determined. Finally, the best flocculants with highest removal
percentages have been determined (QG2001 and Flocudex CS49).
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: Presently a significant portion of the Earth's
population does not have access to healthy food. Either because they
cannot afford it or because they do not know which one are they. The
aim of the VII th Framework Chance project (Nr. 266331) supported
by the European Union has been to develop relatively cheap food
with favourable nutritional value and it should have acceptable
quality for consumers. As one task of the project we manufactured
bread products as a basic food. We examined the enrichment of bread
products with four kinds of bran, with a special milling product of
grain industry (aleurone-rich flour) and with a soy-based sprouted
additive. The applied concentration of the six mentioned additives
has been optimized and the physical properties of the bread products
were monitored. The weight/density of the enriched breads increased
a bit, however the volume and height decreased slightly compared to
the corresponding data of the control bread. The optimized
composition of the final product is favourably affected by these
additives having highly preferred composition from nutritional point
of view.
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: We present a gas-liquid microfluidic system as a
reactor to obtain magnetite nanoparticles with an excellent degree of
control regarding their crystalline phase, shape and size. Several
types of microflow approaches were selected to prevent nanomaterial
aggregation and to promote homogenous size distribution. The
selected reactor consists of a mixer stage aided by ultrasound waves
and a reaction stage using a N2-liquid segmented flow to prevent
magnetite oxidation to non-magnetic phases. A milli-fluidic reactor
was developed to increase the production rate where a magnetite
throughput close to 450 mg/h in a continuous fashion was obtained.
Abstract: Background: Worldwide, at least 2.8 million people
die each year as a result of being overweight or obese, and 35.8
million (2.3%) of global DALYs are caused by overweight or
obesity. Obesity is acknowledged as one of the burning public
health problems reducing life expectancy and quality of life. The
body composition analysis of the university population is essential
in assessing the nutritional status, as well as the risk of developing
diseases associated with abnormal body fat content so as to make
nutritional recommendations. Objectives: The main aim was to
determine the prevalence of obesity and overweight in University
students using Anthropometric analysis and BIA methods. Material
and Methods: In this cross-sectional study, 283 university students
participated. The body composition analysis was undertaken by
using mainly: i) Anthropometric Measurement: Height, Weight,
BMI, waist circumference, hip circumference and skin fold
thickness, ii) Bio-electrical impedance was used for analysis of
body fat mass, fat percent and visceral fat which was measured by
Tanita SC-330P Professional Body Composition Analyzer. The
data so collected were compiled in MS Excel and analyzed for
males and females using SPSS 16. Results and Discussion: The
mean age of the male (n= 153) studied subjects was 25.37 ±2.39
years and females (n=130) was 22.53 ±2.31. The data of BIA
revealed very high mean fat per cent of the female subjects i.e.
30.3±6.5 per cent whereas mean fat per cent of the male subjects
was 15.60±6.02 per cent indicating a normal body fat range. The
findings showed high visceral fat of both males (12.92±3.02) and
females (16.86±4.98). BMI, BF% and WHR were higher among
females, and BMI was higher among males. The most evident
correlation was verified between BF% and WHR for female
students (r=0.902; p