Abstract: High temperature Fischer-Tropsch synthesis process
use fixed fluidized bed as a reactor. In order to understand the flow
behavior in the fluidized bed better, the research of how the radial
velocity affects the entire flow field is necessary. Laser Doppler
Velocimetry (LDV) was used to study the radial velocity distribution
along the diameter direction of the cross-section of the particle in a
fixed fluidized bed. The velocity in the cross-section is fluctuating
within a small range. The direction of the speed is a random
phenomenon. In addition to r/R is 1, the axial velocity are more than 6
times of the radial velocity, the radial velocity has little impact on the
axial velocity in a fixed fluidized bed.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: The present paper attempts to investigate the
prediction of air entrainment rate and aeration efficiency of a free
overfall jets issuing from a triangular sharp crested weir by using
regression based modelling. The empirical equations, Support vector
machine (polynomial and radial basis function) models and the linear
regression techniques were applied on the triangular sharp crested
weirs relating the air entrainment rate and the aeration efficiency to
the input parameters namely drop height, discharge, and vertex angle.
It was observed that there exists a good agreement between the
measured values and the values obtained using empirical equations,
Support vector machine (Polynomial and rbf) models and the linear
regression techniques. The test results demonstrated that the SVM
based (Poly & rbf) model also provided acceptable prediction of the
measured values with reasonable accuracy along with empirical
equations and linear regression techniques in modelling the air
entrainment rate and the aeration efficiency of a free overfall jets
issuing from triangular sharp crested weir. Further sensitivity analysis
has also been performed to study the impact of input parameter on the
output in terms of air entrainment rate and aeration efficiency.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: In this article, we deal with a variant of the classical
course timetabling problem that has a practical application in many
areas of education. In particular, in this paper we are interested in
high schools remedial courses. The purpose of such courses is to
provide under-prepared students with the skills necessary to succeed
in their studies. In particular, a student might be under prepared in
an entire course, or only in a part of it. The limited availability
of funds, as well as the limited amount of time and teachers at
disposal, often requires schools to choose which courses and/or which
teaching units to activate. Thus, schools need to model the training
offer and the related timetabling, with the goal of ensuring the
highest possible teaching quality, by meeting the above-mentioned
financial, time and resources constraints. Moreover, there are some
prerequisites between the teaching units that must be satisfied. We
first present a Mixed-Integer Programming (MIP) model to solve
this problem to optimality. However, the presence of many peculiar
constraints contributes inevitably in increasing the complexity of
the mathematical model. Thus, solving it through a general-purpose
solver may be performed for small instances only, while solving
real-life-sized instances of such model requires specific techniques
or heuristic approaches. For this purpose, we also propose a heuristic
approach, in which we make use of a fast constructive procedure
to obtain a feasible solution. To assess our exact and heuristic
approaches we perform extensive computational results on both
real-life instances (obtained from a high school in Lecce, Italy) and
randomly generated instances. Our tests show that the MIP model is
never solved to optimality, with an average optimality gap of 57%.
On the other hand, the heuristic algorithm is much faster (in about the
50% of the considered instances it converges in approximately half of
the time limit) and in many cases allows achieving an improvement
on the objective function value obtained by the MIP model. Such an
improvement ranges between 18% and 66%.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Human beings have the ability to make logical
decisions. Although human decision - making is often optimal, it is
insufficient when huge amount of data is to be classified. Medical
dataset is a vital ingredient used in predicting patient’s health
condition. In other to have the best prediction, there calls for most
suitable machine learning algorithms. This work compared the
performance of Artificial Neural Network (ANN) and Decision Tree
Algorithms (DTA) as regards to some performance metrics using
diabetes data. WEKA software was used for the implementation of
the algorithms. Multilayer Perceptron (MLP) and Radial Basis
Function (RBF) were the two algorithms used for ANN, while
RegTree and LADTree algorithms were the DTA models used. From
the results obtained, DTA performed better than ANN. The Root
Mean Squared Error (RMSE) of MLP is 0.3913 that of RBF is
0.3625, that of RepTree is 0.3174 and that of LADTree is 0.3206
respectively.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: Radial profiles of particle velocities were investigated
in a 6.1m high methanol-to-olefins cold model experimental device
using a TSI laser Doppler velocimeter. The effect of axial height on
flow development was not obvious in fully developed region under the
same operating condition. Superficial gas velocity and solid
circulating rate had significant influence on particle velocity in the
center region of the riser. Besides, comparisons among rising,
descending and average particle velocity were conducted. The particle
average velocity was similar to the rising particle velocity and higher
than the descending particle velocity in radial locations except the wall
region of riser.
Abstract: The future and the development of science is therefore
seen in interdisciplinary areas such as biomedical engineering. Selfassembled
structures, similar to stem cell niches would inhibit fast
division process and subsequently capture the stem cells from the
blood flow. By means of surface topography and the stiffness as well
as microstructure progenitor cells should be differentiated towards
the formation of endothelial cells monolayer which effectively will
inhibit activation of the coagulation cascade. The idea of the material
surface development met the interest of the clinical institutions,
which support the development of science in this area and are waiting
for scientific solutions that could contribute to the development of
heart assist systems. This would improve the efficiency of the
treatment of patients with myocardial failure, supported with artificial
heart assist systems. Innovative materials would enable the redesign,
in the post project activity, construction of ventricular heart assist.
Abstract: This study aimed to determine the possible protective effects of L‐carnitine against gentamicin‐induced nephrotoxicity. Forty male albino rats were divided into 4 groups (10 rats each); Group 1: normal control, group 2: induced nephrotoxicity (gentamicin 50 mg/kg/day S.C; 8 days), group 3: treated with L‐ carnitine (40 mg/kg/d SC for 12 days) and group 4: treated with L‐ carnitine 4 days before and for 8 days in concomitant with gentamicin. Gentamicin‐induced nephrotoxicity (group 2): caused significant increase in serum urea, creatinine, urinary N‐acetyl‐B‐D‐ glucosaminidase (NAG), gamma glutamyl transpeptidase (GGT), urinary total protein and kidney tissue malondialdehyde (MDA) with significant decrease in serum superoxide dismutase (SOD), serum catalase and creatinine clearance and marked tubular necrosis in the proximal convoluted tubules with interruption in the basement membrane around the necrotic tubule compared to the normal control group. L‐carnitine 4 days before and for 8 days in concomitant with gentamicin (group 4) offered marked decrease in serum urea, serum creatinine, urinary NAG, urinary GGT, urinary proteins and kidney tissue MDA, with marked increase in serum SOD, serum catalase and creatinine clearance with marked improvement in the tubular damage compared to gentamicin‐induced nephrotoxicity group. L‐carnitine administered for 12 days produced no change in the parameters mentioned above as compared to the normal control group. In conclusion: L‐carnitine could reduce most of the biochemical parameters and also improve the histopathological features of kidney asscociated with gentamicin induced‐nephrotoxicity.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: This paper reports a novel actuating design that uses
the shear deformation of a piezoelectric actuator to deflect a
bulge-diaphragm for driving an array microdroplet ejector. In essence,
we employed a circular-shaped actuator poled radial direction with
remnant polarization normal to the actuating electric field for inducing
the piezoelectric shear effect. The array microdroplet ejector consists
of a shear type piezoelectric actuator, a vibration plate, two chamber
plates, two channel plates and a nozzle plate. The vibration, chamber
and nozzle plate components are fabricated using nickel
electroforming technology, whereas the channel plate is fabricated by
etching of stainless steel. The diaphragm displacement was measured
by the laser two-dimensional scanning vibrometer. The ejected
droplets of the microejector were also observed via an optic
visualization system.
Abstract: We evaluate the performance of a numerical method
for global optimization of expensive functions. The method is using a
response surface to guide the search for the global optimum. This
metamodel could be based on radial basis functions, kriging, or a
combination of different models. We discuss how to set the cyclic
parameters of the optimization method to get a balance between local
and global search. We also discuss the eventual problem with Runge
oscillations in the response surface.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: Facing the understanding problem of update and
preservation of urban history space under background of rapid Chinese
urbanization, so at first there is a need to dig the philosophic principles
of “antithesis” and “unification” which are contained in the traditional
Chinese literature known as “antithesis” and do the job of planning
translation by personal understanding in order to form understanding
and value systems of dialectical urban history space under the
foundation of “antithesis”. Then we could put forward a “context”
concept for urban history space under the foregoing basis. After that,
we will take the update and preservation of Ningbo Tianyi Pavilion’s
historical district as an example to discuss problems related to
understanding of urban history area under the basis of Chinese
tradition culture, improvement of value system, construction of urban
trait space and Chinese “localization” of planning theory.
Abstract: The turbocharger and turbocharging have been the
inherent component of diesel engines, so that critical parameters of
such engines, as BSFC (Brake Specific Fuel Consumption) or
thermal efficiency, fuel consumption, BMEP (Brake Mean Effective
Pressure), the power density output and emission level have been
improved extensively. In general, the turbocharger can be considered
as the most complex component of diesel engines, because it has
closely interrelated turbomachinery concepts of the turbines and the
compressors to thermodynamic fundamentals of internal combustion
engines and stress analysis of all components.
In this paper, a waste gate for a conventional single stage radial
turbine is investigated by consideration of turbochargers operation
constrains and engine operation conditions, without any detail
designs in the turbine and the compressor. Amount of opening waste
gate which extended between the ranges of full opened and closed
valve, is demonstrated by limiting compressor boost pressure ratio.
Obtaining of an optimum point by regard above mentioned items is
surveyed by three linked meanline modeling programs together
which consist of Turbomatch®, Compal®, Rital® madules in concepts
NREC® respectively.