Abstract: This research paper aims to identify, analyze and rank
factors affecting labor productivity in Spain with respect to their
relative importance. Using a selected set of 35 factors, a structured
questionnaire survey was utilized as the method to collect data from
companies. Target population is comprised by a random
representative sample of practitioners related with the Spanish
construction industry. Findings reveal the top five ranked factors are
as follows: (1) shortage or late supply of materials; (2) clarity of the
drawings and project documents; (3) clear and daily task assignment;
(4) tools or equipment shortages; (5) level of skill and experience of
laborers. Additionally, this research also pretends to provide simple
and comprehensive recommendations so that they could be
implemented by construction managers for an effective management
of construction labor forces.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: This research proposes a novel reconstruction protocol
for restoring missing surfaces and low-quality edges and shapes in
photos of artifacts at historical sites. The protocol starts with the
extraction of a cloud of points. This extraction process is based on
four subordinate algorithms, which differ in the robustness and
amount of resultant. Moreover, they use different -but
complementary- accuracy to some related features and to the way
they build a quality mesh. The performance of our proposed protocol
is compared with other state-of-the-art algorithms and toolkits. The
statistical analysis shows that our algorithm significantly outperforms
its rivals in the resultant quality of its object files used to reconstruct
the desired model.
Abstract: The article presents the results of the application of
artificial neural networks to separate the fluorescent contribution of
nanodiamonds used as biomarkers, adsorbents and carriers of drugs
in biomedicine, from a fluorescent background of own biological
fluorophores. The principal possibility of solving this problem is
shown. Use of neural network architecture let to detect fluorescence
of nanodiamonds against the background autofluorescence of egg
white with high accuracy - better than 3 ug/ml.
Abstract: In this paper we make a temperature investigations in
two type of superposed crimped connections using experimental
determinations. All the samples use 8 copper wire 7.1 x 3 mm2
crimped by two methods: the first method uses one crimp indents and
the second is a proposed method with two crimp indents. The ferrule
is a parallel one. We study the influence of number and position of
crimp indents. The samples are heated in A.C. current at different
current values until steady state heating regime. After obtaining of
temperature values, we compare them and present the conclusion.
Abstract: Boron-gypsum is a waste which occurs in the boric
acid production process. In this study, the boron content of this waste
is evaluated for the use in synthesis of magnesium borates and such
evaluation of this kind of waste is useful more than storage or
disposal. Magnesium borates, which are a sub-class of boron
minerals, are useful additive materials for the industries due to their
remarkable thermal and mechanical properties. Magnesium borates
were obtained hydrothermally at different temperatures. Novelty of
this study is the search of the solution density effects to magnesium
borate synthesis process for the increasing the possibility of borongypsum
usage as a raw material. After the synthesis process, products
are subjected to XRD and FT-IR to identify and characterize their
crystal structure, respectively.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: Among all FACTS devices, the unified power flow
controller (UPFC) is considered to be the most versatile device.
This is due to its capability to control all the transmission system
parameters (impedance, voltage magnitude, and phase angle). With
the growing interest in UPFC, the attention to develop a mathematical
model has increased. Several models were introduced for UPFC in
literature for different type of studies in power systems. In this paper
a novel comparison study between two dynamic models of UPFC
with their proposed control strategies.
Abstract: Researches and concerns in power quality gained
significant momentum in the field of power electronics systems over
the last two decades globally. This sudden increase in the number of
concerns over power quality problems is a result of the huge increase
in the use of non-linear loads. In this paper, power quality evaluation
of some distribution networks at Misurata - Libya has been done
using a power quality and energy analyzer (Fluke 437 Series II). The
results of this evaluation are used to minimize the problems of power
quality. The analysis shows the main power quality problems that
exist and the level of awareness of power quality issues with the aim
of generating a start point which can be used as guidelines for
researchers and end users in the field of power systems.
Abstract: One of the major goals of Spoken Dialog Systems
(SDS) is to understand what the user utters.
In the SDS domain, the Spoken Language Understanding (SLU)
Module classifies user utterances by means of a pre-definite
conceptual knowledge. The SLU module is able to recognize only the
meaning previously included in its knowledge base. Due the vastity
of that knowledge, the information storing is a very expensive
process.
Updating and managing the knowledge base are time-consuming
and error-prone processes because of the rapidly growing number of
entities like proper nouns and domain-specific nouns. This paper
proposes a solution to the problem of Name Entity Recognition
(NER) applied to a SDS domain. The proposed solution attempts to
automatically recognize the meaning associated with an utterance by
using the PANKOW (Pattern based Annotation through Knowledge
On the Web) method at runtime.
The method being proposed extracts information from the Web to
increase the SLU knowledge module and reduces the development
effort. In particular, the Google Search Engine is used to extract
information from the Facebook social network.
Abstract: Web search engines are designed to retrieve and
extract the information in the web databases and to return dynamic
web pages. The Semantic Web is an extension of the current web in
which it includes semantic content in web pages. The main goal of
semantic web is to promote the quality of the current web by
changing its contents into machine understandable form. Therefore,
the milestone of semantic web is to have semantic level information
in the web. Nowadays, people use different keyword- based search
engines to find the relevant information they need from the web.
But many of the words are polysemous. When these words are
used to query a search engine, it displays the Search Result Records
(SRRs) with different meanings. The SRRs with similar meanings are
grouped together based on Word Sense Disambiguation (WSD). In
addition to that semantic annotation is also performed to improve the
efficiency of search result records. Semantic Annotation is the
process of adding the semantic metadata to web resources. Thus the
grouped SRRs are annotated and generate a summary which
describes the information in SRRs. But the automatic semantic
annotation is a significant challenge in the semantic web. Here
ontology and knowledge based representation are used to annotate
the web pages.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: Azadirachta excelsa or locally known as sentang are
frequently used as a traditional medicine by diabetes patients in
Malaysia. However, less attention has been given to their toxicity
effect. Thus, the study is an attempt to examine the protective effect
of A. excelsa on the pancreas and to determine possible toxicity
mediated by the extract. Diabetes was induced experimentally in rats
by high-fat-diet for 16 weeks followed by intraperitoneal injection of
streptozotocin at dosage of 35 mg/kg of body weight. Declination of
the fasting blood glucose level was observed after continuous
administration of A. excelsa for 14 days twice daily. This is due to the
refining structure of the pancreas. However, surprisingly, the plant
extract reduced the leukocytes, erythrocytes, hemoglobin, MCHC and
lymphocytes. In addition, the rat treated with the plant extract
exhibited increment in AST and eosinocytes level. Overall, the
finding shows that A. excelsa possesses antidiabetic activity by
improving the structure of pancreatic islet of Langerhans but
involved in ameliorating of hematology and biochemical parameters.
Abstract: In this study, six bacterial isolates of a slightly
thermophilic organism from the Sg. Klah hot spring, Malaysia were
successfully isolated and designated as M7T55D1, M7T55D2,
M7T55D3, M7T53D1, M7T53D2 and M7T53D3 respectively. The
bacterial isolates were screened for their cellulose hydrolytic ability
on Carboxymethlycellulose agar medium. The isolated bacterial
strains were identified morphologically, biochemically and
molecularly with the aid of 16S rDNA sequencing. All of the bacteria
showed their optimum growth at a slightly alkaline pH of 7.5 with a
temperature of 55°C. All strains were Gram-negative, non-spore
forming type, strictly aerobic, catalase-positive and oxidase-positive
with the ability to produce thermostable cellulase. Based on BLASTn
results, bacterial isolates of M7T55D2 and M7T53D1 gave the
highest homology (97%) with similarity to Tepidimonas ignava while
isolates M7T55D1, M7T55D3, M7T53D2 and M7T53D3 showed
their closest homology (97%-98%) with Tepidimonas thermarum.
These cellulolytic thermophiles might have a commercial potential to
produce valuable thermostable cellulase.
Abstract: In order to evaluate the performance of a unified power
flow controller (UPFC), mathematical models for steady state and
dynamic analysis are to be developed. The steady state model is
mainly concerned with the incorporation of the UPFC in load flow
studies. Several load flow models for UPFC have been introduced
in literature, and one of the most reliable models is the decoupled
UPFC model. In spite of UPFC decoupled load flow model simplicity,
it is more robust compared to other UPFC load flow models and it
contains unique capabilities. Some shortcoming such as additional
set of nonlinear equations are to be solved separately after the load
flow solution is obtained. The aim of this study is to investigate the
different control strategies that can be realized in the decoupled load
flow model (individual control and combined control), and the impact
of the location of the UPFC in the network on its control parameters.
Abstract: The high Peak to Average Power Ratio (PAR) in Filter
Bank Multicarrier with Offset Quadrature Amplitude Modulation
(FBMC-OQAM) can significantly reduce power efficiency and
performance. In this paper, we address the problem of PAPR
reduction for FBMC-OQAM systems using Tone Reservation (TR)
technique. Due to the overlapping structure of FBMCOQAM signals,
directly applying TR schemes of OFDM systems to FBMC-OQAM
systems is not effective. We improve the tone reservation (TR)
technique by employing sliding window with Active Constellation
Extension for the PAPR reduction of FBMC-OQAM signals, called
sliding window tone reservation Active Constellation Extension
(SW-TRACE) technique. The proposed SW-TRACE technique uses
the peak reduction tones (PRTs) of several consecutive data
blocks to cancel the peaks of the FBMC-OQAM signal inside a
window, with dynamically extending outer constellation points in
active(data-carrying) channels, within margin-preserving constraints,
in order to minimize the peak magnitude. Analysis and simulation
results compared to the existing Tone Reservation (TR) technique for
FBMC/OQAM system. The proposed method SW-TRACE has better
PAPR performance and lower computational complexity.
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: Osteoporosis is a common multifactorial disease with
a strong genetic component characterized by reduced bone mass and
increased risk of fractures. Genetic factors play an important role in
the pathogenesis of osteoporosis. The aim of our study was to
identify the genotype and allele distribution of T245G polymorphism
in OPG gene in Slovak postmenopausal women. A total of 200
unrelated Slovak postmenopausal women with diagnosed
osteoporosis and 200 normal controls were genotyped for T245G
(rs3134069) polymorphism of OPG gene. Genotyping was performed
using the Custom Taqman®SNP Genotyping assays. Genotypes and
alleles frequencies showed no significant differences (p=0.5551;
p=0.6022). The results of the present study confirm the importance of
T245G polymorphism in OPG gene in the pathogenesis of
osteoporosis.
Abstract: An extensive amount of work has been done in data
clustering research under the unsupervised learning technique in Data
Mining during the past two decades. Moreover, several approaches
and methods have been emerged focusing on clustering diverse data
types, features of cluster models and similarity rates of clusters.
However, none of the single clustering algorithm exemplifies its best
nature in extracting efficient clusters. Consequently, in order to
rectify this issue, a new challenging technique called Cluster
Ensemble method was bloomed. This new approach tends to be the
alternative method for the cluster analysis problem. The main
objective of the Cluster Ensemble is to aggregate the diverse
clustering solutions in such a way to attain accuracy and also to
improve the eminence the individual clustering algorithms. Due to
the massive and rapid development of new methods in the globe of
data mining, it is highly mandatory to scrutinize a vital analysis of
existing techniques and the future novelty. This paper shows the
comparative analysis of different cluster ensemble methods along
with their methodologies and salient features. Henceforth this
unambiguous analysis will be very useful for the society of clustering
experts and also helps in deciding the most appropriate one to resolve
the problem in hand.