Abstract: The objective of this study is to evaluate the threshold
stress of the clay with sand subgrade soil. Threshold stress can be
defined as the stress level above which cyclic loading leads to
excessive deformation and eventual failure. The thickness
determination of highways formations using the threshold stress
approach is a more realistic assessment of the soil behaviour because
it is subjected to repeated loadings from moving vehicles. Threshold
stress can be evaluated by plastic strain criterion, which is based on
the accumulated plastic strain behaviour during cyclic loadings [1].
Several conditions of the all-round pressure the subgrade soil namely,
zero confinement, low all-round pressure and high all-round pressure
are investigated. The threshold stresses of various soil conditions are
determined. Threshold stress of the soil are 60%, 31% and 38.6% for
unconfined partially saturated sample, low effective stress saturated
sample, high effective stress saturated sample respectively.
Abstract: The characteristic bending strength (MOR) and mean
modulus of elasticity (MOE) of tropical hardwood red seraya (Shorea
spp.) plywood were determined using European Standard EN310 and
EN789. The thickness of the test specimen was 4.0mm, 7.0mm,
9.0mm, 12.0mm and 15.0mm. The experiment found that the MOR
of red seraya plywood in EN310 is about 12% to 20% and 7% to
24% higher than EN789 whereas MOE were about 28% to 41% and
30% to 36% lower than those obtained from EN 789 for test
specimens parallel and perpendicular to the grain direction. The
linear regression shows that MOR and MOE for EN789 is about 0.8
times less and 1.5 times more than EN310. The experiment also
found that the MOR and MOE of EN310 and EN789 also depend on
the wood species that used in the experiment.
Abstract: Among many agro- based cottage industries in India
sericulture has been promoted as an agro-based, labor intensive, rural
oriented cottage industry, providing gainful employment mainly to
the weaker and marginalized section of the society specially tribal.
Sericulture occupies the place of pride in the rural economy can be
practiced even with very low land holding, low gestation, high
returns make sericulture an ideal program, requiring little capital
investment. In 2010-2011 the employment in sericulture sector was
72.5 lakh persons. The involvement of landless rural people in tasar
sericulture is because they understood its potential for rural and tribal
upliftment. This article demonstrates that certain developmental
initiatives have been playing an important role in the socio-economic
progress of tribal masses in Raigarh district and explains the
increased returns from sericulture as a result of development
programs. The study concludes with some suggestions to improve the
long term feasibility of sericulture.
Abstract: Von Willebrand-s disease is the most common
inherited bleeding disorder in humans, it
caused by qualitative abnormalities of the von Willebrand factor
(vWF). Our objective is to determine the prevalence of this disease at
part of the Algerian population in the East and the South by a
biological diagnosis based on specific biological tests (automated
platelet count, the bleeding time (TS), the time of cephalin + activator
(TCA), measure of the prothrombin rate (TP), vWF rate and factor
VIII rate, Molecular electrophoresis of vWF multimers in agarose gel
in the presence of SDS). Four patients of type III or severe
Willebrand-s disease were found on 200 suspect cases. All cases are
showed a deficit in vWF rate (< 5%), and factor VIII (P
Abstract: K-Modes is an extension of K-Means clustering algorithm, developed to cluster the categorical data, where the mean is replaced by the mode. The similarity measure proposed by Huang is the simple matching or mismatching measure. Weight of attribute values contribute much in clustering; thus in this paper we propose a new weighted dissimilarity measure for K-Modes, based on the ratio of frequency of attribute values in the cluster and in the data set. The new weighted measure is experimented with the data sets obtained from the UCI data repository. The results are compared with K-Modes and K-representative, which show that the new measure generates clusters with high purity.
Abstract: The cost of developing the software from scratch can
be saved by identifying and extracting the reusable components from
already developed and existing software systems or legacy systems
[6]. But the issue of how to identify reusable components from
existing systems has remained relatively unexplored. We have used
metric based approach for characterizing a software module. In this
present work, the metrics McCabe-s Cyclometric Complexity
Measure for Complexity measurement, Regularity Metric, Halstead
Software Science Indicator for Volume indication, Reuse Frequency
metric and Coupling Metric values of the software component are
used as input attributes to the different types of Neural Network
system and reusability of the software component is calculated. The
results are recorded in terms of Accuracy, Mean Absolute Error
(MAE) and Root Mean Squared Error (RMSE).
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: This paper discusses the cued speech recognition
methods in videoconference. Cued speech is a specific gesture
language that is used for communication between deaf people. We
define the criteria for sentence intelligibility according to answers of
testing subjects (deaf people). In our tests we use 30 sample videos
coded by H.264 codec with various bit-rates and various speed of
cued speech. Additionally, we define the criteria for consonant sign
recognizability in single-handed finger alphabet (dactyl) analogically
to acoustics. We use another 12 sample videos coded by H.264 codec
with various bit-rates in four different video formats. To interpret the
results we apply the standard scale for subjective video quality
evaluation and the percentual evaluation of intelligibility as in
acoustics. From the results we construct the minimum coded bit-rate
recommendations for every spatial resolution.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: Cassava bagasse is one of major biomass wastes in Thailand from starch processing industry, which contains high starch content of about 60%. The object of this study was to investigate the optimal condition for hydrothermally pretreating cassava baggasses with or without acid addition. The pretreated samples were measured reducing sugar yield directly or after enzymatic hydrolysis (alpha-amylase). In enzymatic hydrolysis, the highest reducing sugar content was obtained under hydrothermal conditions for at 125oC for 30 min. The result shows that pretreating cassava baggasses increased the efficiency of enzymatic hydrolysis. For acid hydrolysis, pretreating cassava baggasses with sulfuric acid at 120oC for 60 min gave a maximum reducing sugar yield. In this study, sulfuric acid had a greater capacity for hydrolyzing cassava baggasses than phosphoric acid. In comparison, dilute acid hydrolysis to provide a higher yield of reducing sugar than the enzymatic hydrolysis combined hydrothermal pretreatment. However, enzymatic hydrolysis in a combination with hydrothermal pretreatment was an alternative to enhance efficiency reducing sugar production from cassava bagasse.
Abstract: The requirement to improve software productivity has
promoted the research on software metric technology. There are
metrics for identifying the quality of reusable components but the
function that makes use of these metrics to find reusability of
software components is still not clear. These metrics if identified in
the design phase or even in the coding phase can help us to reduce the
rework by improving quality of reuse of the component and hence
improve the productivity due to probabilistic increase in the reuse
level. CK metric suit is most widely used metrics for the objectoriented
(OO) software; we critically analyzed the CK metrics, tried
to remove the inconsistencies and devised the framework of metrics
to obtain the structural analysis of OO-based software components.
Neural network can learn new relationships with new input data and
can be used to refine fuzzy rules to create fuzzy adaptive system.
Hence, Neuro-fuzzy inference engine can be used to evaluate the
reusability of OO-based component using its structural attributes as
inputs. In this paper, an algorithm has been proposed in which the
inputs can be given to Neuro-fuzzy system in form of tuned WMC,
DIT, NOC, CBO , LCOM values of the OO software component and
output can be obtained in terms of reusability. The developed
reusability model has produced high precision results as expected by
the human experts.
Abstract: This paper presents a heuristic approach to solve the Generalized Assignment Problem (GAP) which is NP-hard. It is worth mentioning that many researches used to develop algorithms for identifying the redundant constraints and variables in linear programming model. Some of the algorithms are presented using intercept matrix of the constraints to identify redundant constraints and variables prior to the start of the solution process. Here a new heuristic approach based on the dominance property of the intercept matrix to find optimal or near optimal solution of the GAP is proposed. In this heuristic, redundant variables of the GAP are identified by applying the dominance property of the intercept matrix repeatedly. This heuristic approach is tested for 90 benchmark problems of sizes upto 4000, taken from OR-library and the results are compared with optimum solutions. Computational complexity is proved to be O(mn2) of solving GAP using this approach. The performance of our heuristic is compared with the best state-ofthe- art heuristic algorithms with respect to both the quality of the solutions. The encouraging results especially for relatively large size test problems indicate that this heuristic approach can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: Frequent machine breakdowns, low plant availability and increased overtime are a great threat to a manufacturing plant as they increase operating costs of an industry. The main aim of this study was to improve Overall Equipment Effectiveness (OEE) at a manufacturing company through the implementation of innovative maintenance strategies. A case study approach was used. The paper focuses on improving the maintenance in a manufacturing set up using an innovative maintenance regime mix to improve overall equipment effectiveness. Interviews, reviewing documentation and historical records, direct and participatory observation were used as data collection methods during the research. Usually production is based on the total kilowatt of motors produced per day. The target kilowatt at 91% availability is 75 Kilowatts a day. Reduced demand and lack of raw materials particularly imported items are adversely affecting the manufacturing operations. The company had to reset its targets from the usual figure of 250 Kilowatt per day to mere 75 per day due to lower availability of machines as result of breakdowns as well as lack of raw materials. The price reductions and uncertainties as well as general machine breakdowns further lowered production. Some recommendations were given. For instance, employee empowerment in the company will enhance responsibility and authority to improve and totally eliminate the six big losses. If the maintenance department is to realise its proper function in a progressive, innovative industrial society, then its personnel must be continuously trained to meet current needs as well as future requirements. To make the maintenance planning system effective, it is essential to keep track of all the corrective maintenance jobs and preventive maintenance inspections. For large processing plants these cannot be handled manually. It was therefore recommended that the company implement (Computerised Maintenance Management System) CMMS.
Abstract: Optimal cultural site selection is one of the ways that
can lead to the promotion of citizenship culture in addition to
ensuring the health and leisure of city residents. This study examines
the social and cultural needs of the community and optimal cultural
site allocation and after identifying the problems and shortcomings,
provides a suitable model for finding the best location for these
centers where there is the greatest impact on the promotion of
citizenship culture. On the other hand, non-scientific methods cause
irreversible impacts to the urban environment and citizens. But
modern efficient methods can reduce these impacts. One of these
methods is using geographical information systems (GIS). In this
study, Analytical Hierarchy Process (AHP) method was used to
locate the optimal cultural site. In AHP, three principles
(decomposition), (comparative analysis), and (combining
preferences) are used. The objectives of this research include
providing optimal contexts for passing time and performing cultural
activities by Shiraz residents and also proposing construction of some
cultural sites in different areas of the city. The results of this study
show the correct positioning of cultural sites based on social needs of
citizens. Thus, considering the population parameters and radii
access, GIS and AHP model for locating cultural centers can meet
social needs of citizens.
Abstract: The talks about technological convergence had been
around for almost twenty years. Today Internet made it possible. And
this is not only technical evolution. The way it changed our lives
reflected in variety of applications, services and technologies used in
day-to-day life. Such benefits imposed even more requirements on
heterogeneous and unreliable IP networks.
Current paper outlines QoS management system developed in the
NetQoS [1] project. It describes an overall architecture of
management system for heterogeneous networks and proposes
automated multi-layer QoS management. Paper focuses on the
structure of the most crucial modules of the system that enable
autonomous and multi-layer provisioning and dynamic adaptation.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.