Abstract: In this paper, an attempt has been made to study the
effect of thermal gradation on the steady-state creep behavior of
rotating isotropic disc made of functionally graded material using
threshold stress based Sherby’s creep law. The composite discs made
of aluminum matrix reinforced with silicon carbide particulate have
been taken for analysis. The stress and strain rate distributions have
been calculated for the discs rotating at elevated temperatures having
thermal gradation. The material parameters of creep vary radially and
have been estimated by regression fit of the available experimental
data. Investigations for discs made up of linearly increasing particle
content operating under linearly decreasing temperature from inner
to outer radii have been done using von Mises’ yield criterion. The
results are displayed and compared graphically in designer friendly
format for the above said disc profile with the disc made of particle
reinforced composite operating under uniform temperature profile. It
is observed that radial and tangential stresses show minor variation
and the strain rates vary significantly in the presence of thermal
gradation as compared to disc having uniform temperature.
Abstract: The present paper investigates the effect of linear
thermal gradient on the steady-state creep behavior of rotating
isotropic disc using threshold stress based Sherby’s creep law.
The composite discs made of aluminum matrix reinforced with
silicon carbide particulate has been taken for analysis. The stress
and strain rate distributions have been calculated for discs rotating
at linear thermal gradation using von Mises’ yield criterion. The
material parameters have been estimated by regression fit of the
available experimental data. The results are displayed and compared
graphically in designer friendly format for the above said temperature
profile with the disc operating under uniform temperature profile. It is
observed that radial and tangential stresses show minor variation and
the strain rates vary significantly in the presence of thermal gradation
as compared to disc having uniform temperature.
Abstract: The present study focused on carrying out the creep analysis in an isotropic thick-walled composite cylindrical pressure vessel composed of aluminum matrix reinforced with silicon-carbide in particulate form. The creep behavior of the composite material has been described by the threshold stress based creep law. The values of stress exponent appearing in the creep law were selected as 3, 5 and 8. The constitutive equations were developed using well known von-Mises yield criteria. Models were developed to find out the distributions of creep stress and strain rate in thick-walled composite cylindrical pressure vessels under internal pressure. In order to obtain the stress distributions in the cylinder, the equilibrium equation of the continuum mechanics and the constitutive equations are solved together. It was observed that the radial stress, tangential stress and axial stress increases along with the radial distance. The cross-over was also obtained almost at the middle region of cylindrical vessel for tangential and axial stress for different values of stress exponent. The strain rates were also decreasing in nature along the entire radius.
Abstract: Creep behavior of thick-walled functionally graded cylinder consisting of AlSiC and subjected to internal pressure and high temperature has been analyzed. The functional relationship between strain rate with stress can be described by the well known threshold stress based creep law with a stress exponent of five. The effect of imposing non-linear particle gradient on the distribution of creep stresses in the thick-walled functionally graded composite cylinder has been investigated. The study revealed that for the assumed non-linear particle distribution, the radial stress decreases throughout the cylinder, whereas the tangential, axial and effective stresses have averaging effect. The strain rates in the functionally graded composite cylinder could be reduced to significant extent by employing non-linear gradient in the distribution of reinforcement.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: The objective of this study is to evaluate the threshold
stress of the clay with sand subgrade soil. Threshold stress can be
defined as the stress level above which cyclic loading leads to
excessive deformation and eventual failure. The thickness
determination of highways formations using the threshold stress
approach is a more realistic assessment of the soil behaviour because
it is subjected to repeated loadings from moving vehicles. Threshold
stress can be evaluated by plastic strain criterion, which is based on
the accumulated plastic strain behaviour during cyclic loadings [1].
Several conditions of the all-round pressure the subgrade soil namely,
zero confinement, low all-round pressure and high all-round pressure
are investigated. The threshold stresses of various soil conditions are
determined. Threshold stress of the soil are 60%, 31% and 38.6% for
unconfined partially saturated sample, low effective stress saturated
sample, high effective stress saturated sample respectively.
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.