Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: Research in e-Business has been growing
tremendously covering all related aspects such as adoption issues, e-
Business models, strategies, etc. This research aims to explore the
potential of adopting e-Business for a micro size business operating
from home called home-based businesses (HBBs). In Malaysia, the
HBB industry started many years ago and were mostly monopolized
by women or housewives managed as a part-time job to support their
family economy. Today, things have changed. The availability of the
Internet technology and the emergence of e-Business concept
promote the evolution of HBBs, which have been adopted as another
alternative as a professional career for women without neglecting
their family needs especially the children. Although this study is
confined to a limited sample size and within geographical biasness,
the findings show that it concurs with previous large scale studies. In
this study, both qualitative and quantitative methods were used and
data were gathered using triangulation methods via interview, direct
observation, document analysis and survey questionnaires. This paper
discusses the literature review, research methods and findings
pertaining to e-Business adoption factors that influence the HBBs in
Malaysia.
Abstract: The evaluation of energy release rate and centre Crack
Opening Displacement (COD) for circumferential Through-Wall
Cracked (TWC) pipes is an important issue in the assessment of
critical crack length for unstable fracture. The ability to predict crack
growth continues to be an important component of research for
several structural materials. Crack growth predictions can aid the
understanding of the useful life of a structural component and the
determination of inspection intervals and criteria. In this context,
studies were carried out at CSIR-SERC on Nuclear Power Plant
(NPP) piping components subjected to monotonic as well as cyclic
loading to assess the damage for crack growth due to low-cycle
fatigue in circumferentially TWC pipes.
Abstract: In this paper 2D Simulation of catalytic Fixed Bed Reactor in Fischer-Tropsch Synthesis of GTL technology has been performed utilizing computational fluid dynamics (CFD). Synthesis gas (a mixture of carbon monoxide and hydrogen) has been used as feedstock. The reactor was modeled and the model equations were solved employing finite volume method. The model was validated against the experimental data reported in literature. The comparison showed a good agreement between simulation results and the experimental data. In addition, the model was applied to predict the concentration contours of the reactants and products along the length of reactor.
Abstract: A vast array of biological materials, especially algae have received increasing attention for heavy metal removal. Algae have been proven to be cheaper, more effective for the removal of metallic elements in aqueous solutions. A fresh water algal strain was isolated from Zoo Lake, Johannesburg, South Africa and identified as Desmodesmus sp. This paper investigates the efficacy of Desmodesmus sp.in removing heavy metals contaminating the Wonderfonteinspruit Catchment Area (WCA) water bodies. The biosorption data fitted the pseudo-second order and Langmuir isotherm models. The Langmuir maximum uptakes gave the sequence: Mn2+>Ni2+>Fe2+. The best results for kinetic study was obtained in concentration 120 ppm for Fe3+ and Mn2+, whilst for Ni2+ was at 20 ppm, which is about the same concentrations found in contaminated water in the WCA (Fe3+115 ppm, Mn2+ 121 ppm and Ni2+ 26.5 ppm).
Abstract: This paper focuses attention on specific aspects of
entrepreneurial decisions relating to investment, both in the total
fixed investments and plant & machinery (separately). Demand and
financial factors, internal and external, are considered in the
investment analysis. Finally the influence of determinants of fixed
investment and investment plans are examined in Electric Power
industry in India.
Abstract: The present study has been conducted to characterize
the prophenoloxidase (PPO) system of the desert locust, Schistocerca
gregaria following injection of Bacillus thuringiensis kurstaki (Bt).
The bulk of PPO system was associated with haemocytes and a little
amount was found in plasma. This system was activated by different
activators such as laminarin, lipopolysaccharide (LPS) and trypsin
suggesting that the stimulatory mechanism may involve an enzyme
cascade of one or more associated molecules. These activators did
not activate all the molecules of the cascade. Presence of
phenoloxidase activity (PO) coincides with the appearance of protein
band with molecular weight (MW) 70.154 KD (Kilo Dalton).
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: The current research paper is an implementation of
Eigen Faces and Karhunen-Loeve Algorithm for face recognition.
The designed program works in a manner where a unique
identification number is given to each face under trial. These faces
are kept in a database from where any particular face can be matched
and found out of the available test faces. The Karhunen –Loeve
Algorithm has been implemented to find out the appropriate right
face (with same features) with respect to given input image as test
data image having unique identification number. The procedure
involves usage of Eigen faces for the recognition of faces.
Abstract: In Thailand, both the 1997 and the current 2007 Thai Constitutions have mentioned the establishment of independent organizations as a new mechanism to play a key role in proposing policy recommendations to national decision-makers in the interest of collective consumers. Over the last ten years, no independent organizations have yet been set up. Evidently, nobody could point out who should be key players in establishing provincial independent consumer bodies. The purpose of this study was to find definitive stakeholders in establishing and developing independent consumer bodies in a Thai context. This was a cross-sectional study between August and September 2007, using a postal questionnaire with telephone follow-up. The questionnaire was designed and used to obtain multiple stakeholder assessment of three key attributes (power, interest and influence). Study population was 153 stakeholders associated with policy decision-making, formulation and implementation processes of civil-based consumer protection in pilot provinces. The population covered key representatives from five sectors (academics, government officers, business traders, mass media and consumer networks) who participated in the deliberative forums at 10 provinces. A 49.7% response rate was achieved. Data were analyzed, comparing means of three stakeholder attributes and classification of stakeholder typology. The results showed that the provincial health officers were the definitive stakeholders as they had legal power, influence and interest in establishing and sustaining the independent consumer bodies. However, only a few key representatives of the provincial health officers expressed their own paradigm on the civil-based consumer protection. Most provincial health officers put their own standpoint of building civic participation at only a plan-implementation level. For effective policy implementation by the independent consumer bodies, the Thai government should provide budgetary support for the operation of the provincial health officers with their paradigm shift as well as their own clarified standpoint on corporate governance.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: This article is dedicated to development of
mathematical models for determining the dynamics of
concentration of hazardous substances in urban turbulent
atmosphere. Development of the mathematical models implied
taking into account the time-space variability of the fields of
meteorological items and such turbulent atmosphere data as vortex
nature, nonlinear nature, dissipativity and diffusivity. Knowing the
turbulent airflow velocity is not assumed when developing the
model. However, a simplified model implies that the turbulent and
molecular diffusion ratio is a piecewise constant function that
changes depending on vertical distance from the earth surface.
Thereby an important assumption of vertical stratification of urban
air due to atmospheric accumulation of hazardous substances
emitted by motor vehicles is introduced into the mathematical
model. The suggested simplified non-linear mathematical model of
determining the sought exhaust concentration at a priori unknown
turbulent flow velocity through non-degenerate transformation is
reduced to the model which is subsequently solved analytically.
Abstract: Character segmentation is an important preprocessing step for text recognition. In degraded documents, existence of touching characters decreases recognition rate drastically, for any optical character recognition (OCR) system. In this paper a study of touching Gurmukhi characters is carried out and these characters have been divided into various categories after a careful analysis.Structural properties of the Gurmukhi characters are used for defining the categories. New algorithms have been proposed to segment the touching characters in middle zone. These algorithms have shown a reasonable improvement in segmenting the touching characters in degraded Gurmukhi script. The algorithms proposed in this paper are applicable only to machine printed text.
Abstract: Theexperiment was carried out with 2x5 male Merino
lambs raised under intensive conditions to investigate the effect of
dietary calcium soap of linseed oil on the color and fatty acid
composition of longissimusdorsi muscle. Control lambs fed a basal
diet and the experimental lambs consumed a diet supplemented with
3% calcium soap of linseed oil. The color values (L*, a*, b* a*/b*
and chroma) were not influenced by dietary treatment. The MUFA
proportion reduced, SFA and PUFA content did not alter. As
expected, the linolenic (C18:3 n3) and thusthe n-3 content
significantly improved by linseed supplement (0.47 and 0.81; 0.78
and 1.16 in control and in experimental samples, respectively). Other
n-3 and n-6 fatty acids had similar valuestocontrol samples. The n-
6/n-3 ratio was significantly narrower in the experimental group (6.31
vs. 9.38) but the P/S ratio did not differ betweenthe two groups.In
conclusion calcium soap of linseed oil seems to be a suitable
supplement form of n-3 fatty acids to improve the nutritive value of
lamb meat.
Abstract: The aim of this research is to propose a Measurement
Scale for Patient Satisfaction (MSPS) in the context of Tunisian
private clinics. This scale is developed using value management
methods and is validated by statistic tools with SPSS.
Abstract: The protection of parallel transmission lines has been a challenging task due to mutual coupling between the adjacent circuits of the line. This paper presents a novel scheme for detection and classification of faults on parallel transmission lines. The proposed approach uses combination of wavelet transform and neural network, to solve the problem. While wavelet transform is a powerful mathematical tool which can be employed as a fast and very effective means of analyzing power system transient signals, artificial neural network has a ability to classify non-linear relationship between measured signals by identifying different patterns of the associated signals. The proposed algorithm consists of time-frequency analysis of fault generated transients using wavelet transform, followed by pattern recognition using artificial neural network to identify the type of the fault. MATLAB/Simulink is used to generate fault signals and verify the correctness of the algorithm. The adaptive discrimination scheme is tested by simulating different types of fault and varying fault resistance, fault location and fault inception time, on a given power system model. The simulation results show that the proposed scheme for fault diagnosis is able to classify all the faults on the parallel transmission line rapidly and correctly.
Abstract: In this paper, an experimentation to enhance the
visibility of hot objects in a thermal image acquired with ordinary
digital camera is reported, after the applications of lowpass and
median filters to suppress the distracting granular noises. The
common thresholding and slicing techniques were used on the
histogram at different gray levels, followed by a subjective
comparative evaluation. The best result came out with the threshold
level 115 and the number of slices 3.