Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.
Abstract: We studied the selection of nest sites by Persian
ground Jay (Podoces pleskei), in a semi -desert central Iran. Habitat
variables such as plant species number, height of plant species,
vegetation percent and distance to water sources of nest sites were
compared with randomly selected non- used sites. The results showed that the most important factors influencing nesting site selection were total vegetation percent and number of shrubs
(Zgophyllum eurypterum and Atraphaxis spinosa). The mean vegetation percent of 20 area selected by Persian Ground Jay was
(4.41+ 0.17), which was significantly larger than that of the non –
selected area (2.08 + 0.06). The number of Zygophyllum eurypterum (1.13+ 0.01) and Atraphaxis spinosa (1.36+ 0.10) were also significantly higher compared with the control area (0.43+ 0.07)
and (0.58+ 0.9) respectively.
Abstract: This paper represents an investigation on how exploiting multiple transmit antennas by OFDM based wireless LAN subscribers can mitigate physical layer error rate. Then by comparing the Wireless LANs that utilize spatial diversity techniques with the conventional ones it will reveal how PHY and TCP throughputs behaviors are ameliorated. In the next step it will assess the same issues based on a cellular context operation which is mainly introduced as an innovated solution that beside a multi cell operation scenario benefits spatio-temporal signaling schemes as well. Presented simulations will shed light on the improved performance of the wide range and high quality wireless LAN services provided by the proposed approach.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.
Abstract: Building maintenance plays an important role among other activities in building operation. Building defect and damages are part of the building maintenance 'bread and butter' as their input indicated in the building inspection is very much justified, particularly as to determine the building performance. There will be no escape route or short cut from building maintenance work. This study attempts to identify a competitive performance that translates the Critical Success Factor achievements and satisfactorily meet the university-s expectation. The quality and efficiency of maintenance management operation of building depends, to some extent, on the building condition information, the expectation from the university sector and the works carried out for each maintenance activity. This paper reviews the critical success factor in building maintenance management practice for university sectors from four (4) perspectives which include (1) customer (2) internal processes (3) financial and (4) learning and growth perspective. The enhancement of these perspectives is capable to reach the maintenance management goal for a better living environment in university campus.
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: The aim of the present study was to develop and
validate an inexpensive and simple high performance liquid
chromatographic (HPLC) method for the determination of colistin
sulfate. Separation of colistin sulfate was achieved on a ZORBAX
Eclipse XDB-C18 column using UV detection at λ=215 nm. The
mobile phase was 30 mM sulfate buffer (pH 2.5):acetonitrile(76:24).
An excellent linearity (r2=0.998) was found in the concentration
range of 25 - 400 μg/mL. Intra- day and inter-day precisions of
method (%RSD, n=3) were less than 7.9%.The developed and
validated method was applied to determination of the content of
colistin sulfate in medicated premix and animal feed sample.The
recovery of colistin from animal feed was satisfactorily ranged from
90.92 to 93.77%. The results demonstrated that the HPLC method
developed in this work is appropriate for direct determination of
colistin sulfate in commercial medicated premixes and animal feed.
Abstract: Speckled images arise when coherent microwave,
optical, and acoustic imaging techniques are used to image an object, surface or scene. Examples of coherent imaging systems include synthetic aperture radar, laser imaging systems, imaging sonar
systems, and medical ultrasound systems. Speckle noise is a form of object or target induced noise that results when the surface of the object is Rayleigh rough compared to the wavelength of the illuminating radiation. Detection and estimation in images corrupted
by speckle noise is complicated by the nature of the noise and is not
as straightforward as detection and estimation in additive noise. In
this work, we derive stochastic models for speckle noise, with an emphasis on speckle as it arises in medical ultrasound images. The
motivation for this work is the problem of segmentation and tissue classification using ultrasound imaging. Modeling of speckle in this
context involves partially developed speckle model where an underlying Poisson point process modulates a Gram-Charlier series
of Laguerre weighted exponential functions, resulting in a doubly
stochastic filtered Poisson point process. The statistical distribution of partially developed speckle is derived in a closed canonical form.
It is observed that as the mean number of scatterers in a resolution cell is increased, the probability density function approaches an
exponential distribution. This is consistent with fully developed speckle noise as demonstrated by the Central Limit theorem.
Abstract: Wireless sensor networks (WSN) consists of many
sensor nodes that are placed on unattended environments such as
military sites in order to collect important information.
Implementing a secure protocol that can prevent forwarding forged
data and modifying content of aggregated data and has low delay
and overhead of communication, computing and storage is very
important. This paper presents a new protocol for concealed data
aggregation (CDA). In this protocol, the network is divided to
virtual cells, nodes within each cell produce a shared key to send
and receive of concealed data with each other. Considering to data
aggregation in each cell is locally and implementing a secure
authentication mechanism, data aggregation delay is very low and
producing false data in the network by malicious nodes is not
possible. To evaluate the performance of our proposed protocol, we
have presented computational models that show the performance
and low overhead in our protocol.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: We present a visualization technique for radial drawing of trees consisting of two slightly different algorithms. Both of them make use of node-link diagrams for visual encoding. This visualization creates clear drawings without edge crossing. One of the algorithms is suitable for real-time visualization of large trees, as it requires minimal recalculation of the layout if leaves are inserted or removed from the tree; while the other algorithm makes better utilization of the drawing space. The algorithms are very similar and follow almost the same procedure but with different parameters. Both algorithms assign angular coordinates for all nodes which are then converted into 2D Cartesian coordinates for visualization. We present both algorithms and discuss how they compare to each other.
Abstract: In order to compare vertical stratification, floristic composition, and woody species diversity of subtropical evergreen broadleaf forests between the Ryukyu Archipelago, Japan, and South China, tree censuses in a 400 m2 plot in Ishigaki Island and a 1225 m2 plot in Dinghushan Nature Reserve were performed. Both of the subtropical forests consisted of five vertical strata. The floristic composition of the Ishigaki forest was quite different from that of the Dinghushan forest in terms of similarity on a species level (Kuno-s similarity index r0 = 0.05). The values of Shannon-s index H' and Pielou-s index J ' tended to increase from the bottom stratum upward in both forests, except H' for the top stratum in the Ishigaki forest and the upper two strata in the Dinghushan forest. The woody species diversity in the Dinghushan forest (H'= 3.01 bit) was much lower than that in the Ishigaki forest (H'= 4.36 bit).
Abstract: Tehran, one of the heavily-populated capitals, is
severely suffering from increasing air pollution. To show a
documented trend of such pollutants during last years, plane tree
species (Platanus orientalis) were suited to be studied as indicators,
for the species have been planted throughout the city many years
ago. Two areas (Saadatabad and Narmak districts) allotting different
contents of crowed and highly-traffic routs but the same ecological
characteristics were selected. Twelve sample individuals were cored
twice perpendicularly in each area. Tree-rings of each core were
measured by a binocular microscope and separated annually for the
last 25 years. Two heavy metals including Cd and Pb accompanied
by a mineral element (Ca) were analyzed using Hatch method. Treerings
analysis of the two areas showed different groups in term of
physiologically ability as the growths were plunged during the last
10 years in Saadatabad district and showed a slight decrease in the
same period for another studying area. In direct contrast to
decreasing growth trend in Saadatabad, all three mentioned elements
increased sharply during last 25 years in the same area. When it came
to Narmak district, the trend was completely different with
Saadatabad. There were some fluctuations in absorbing trace
elements like tree-rings widths were, yet calcium showed an upward
trend all the last 25 years. The results of the study proved the
possibility of using tree species of each region to monitor its air
pollution trends of the past, hence to depict a pollution assessment of
a populated city for last years and then to make appropriate decisions
for the future as it is well-known what the trend is. On the other
hand, risen values of calcium (as the stress-indicator element)
accompanied by increased trace elements suggests non-sustainable
state of the trees.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: Many commercial processes are available for the
removal of H2S from gaseous streams. The desulfurization of gas
streams using aqueous ferric sulfate solution as washing liquor is
studied. Apart from sulfur, only H2O is generated in the process, and
consequently, no waste treatment facilities are required. A distinct
advantage of the process is that the reaction of H2S with is so rapid
and complete that there remains no danger of discharging toxic waste
gas. In this study, the reactive absorption of hydrogen sulfide into
aqueous ferric sulfate solution has been studied and design
calculations for equipments have been done and effective operation
parameters on this process considered. Results show that high
temperature and low pressure are suitable for absorption reaction.
Variation of hydrogen sulfide concentration and Fe3+ concentration
with time in absorption reaction shown that the reaction of ferric
sulfate and hydrogen sulfide is first order with respect to the both
reactant. At low Fe2(SO4)3 concentration the absorption rate of H2S
increase with increasing the Fe2(SO4)3 concentration. At higher
concentration a decrease in the absorption rate was found. At higher
concentration of Fe2(SO4)3, the ionic strength and viscosity of
solution increase remarkably resulting in a decrease of solubility,
diffusivity and hence absorption rate.