Abstract: A Personal Distributed Environment (PDE) is an
example of an IP-based system architecture designed for future
mobile communications. In a single PDE, there exist several Subnetworks
hosting devices located across the infrastructure, which will
inter-work with one another through the coordination of a Device
Management Entity (DME). Some of these Sub-networks are fixed
and some are mobile. In order to support Mobile Sub-networks
mobility in the PDE, the PDE-NEMO protocol was proposed. This
paper discussed the signalling cost analysis of PDE-NEMO by use of
a detailed simulation model. The paper started with the introduction
of the protocol, followed by the experiments and results and then
followed by discussions.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: Adsorption of Toluidine blue dye from aqueous solutions onto Neem Leaf Powder (NLP) has been investigated. The surface characterization of this natural material was examined by Particle size analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffraction (XRD). The effects of process parameters such as initial concentration, pH, temperature and contact duration on the adsorption capacities have been evaluated, in which pH has been found to be most effective parameter among all. The data were analyzed using the Langmuir and Freundlich for explaining the equilibrium characteristics of adsorption. And kinetic models like pseudo first- order, second-order model and Elovich equation were utilized to describe the kinetic data. The experimental data were well fitted with Langmuir adsorption isotherm model and pseudo second order kinetic model. The thermodynamic parameters, such as Free energy of adsorption (AG"), enthalpy change (AH') and entropy change (AS°) were also determined and evaluated.
Abstract: Intelligent systems based on machine learning
techniques, such as classification, clustering, are gaining wide spread
popularity in real world applications. This paper presents work on
developing a software system for predicting crop yield, for example
oil-palm yield, from climate and plantation data. At the core of our
system is a method for unsupervised partitioning of data for finding
spatio-temporal patterns in climate data using kernel methods which
offer strength to deal with complex data. This work gets inspiration
from the notion that a non-linear data transformation into some high
dimensional feature space increases the possibility of linear
separability of the patterns in the transformed space. Therefore, it
simplifies exploration of the associated structure in the data. Kernel
methods implicitly perform a non-linear mapping of the input data
into a high dimensional feature space by replacing the inner products
with an appropriate positive definite function. In this paper we
present a robust weighted kernel k-means algorithm incorporating
spatial constraints for clustering the data. The proposed algorithm
can effectively handle noise, outliers and auto-correlation in the
spatial data, for effective and efficient data analysis by exploring
patterns and structures in the data, and thus can be used for
predicting oil-palm yield by analyzing various factors affecting the
yield.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: This article presents the analysis of experimental values regarding cracking pattern, specific strains and deformability for reinforced high strength concrete beams. The beams have the concrete class C80/95 and a longitudinal reinforcement ratio of 2.01%, respectively 3.39%. The elements were subjected to flexure under static short-term and long-term loading. The experimental values are compared with calculation values using the design relationships according to Eurocode 2.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: The importance of inter-organizational system (IOS)
has been increasingly recognized by organizations. However, IOS
adoption has proved to be difficult and, at this stage, why this is so is
not fully uncovered. In practice, benefits have often remained
concentrated, primarily accruing to the dominant party, resulting in
low rates of adoption and usage, and often culminating in the failure
of the IOS. The main research question is why organizations initiate
or join IOS and what factors influence their adoption and use levels.
This paper reviews the literature on IOS adoption and proposes a
theoretical framework in order to identify the critical factors to
capture a complete picture of IOS adoption. With our proposed
critical factors, we are able to investigate their relative contributions
to IOS adoption decisions. We obtain findings that suggested that
there are five groups of factors that significantly affect the adoption
and use decision of IOS in the Supply Chain Management (SCM)
context: 1) interorganizational context, 2) organizational context, 3)
technological context, 4) perceived costs, and 5) perceived benefits.
Abstract: MABENA model is a complementary model in
comparison with traditional models such as HCMS, CMS and etc.
New factors, which have effects on preparation of strategic plans and
their sequential order in MABENA model is the platform of
presented road map in this paper.Study review shows, factors such as
emerging new critical success factors for strategic planning,
improvement of international strategic models, increasing the
maturity of companies and emerging new needs leading to design a
new model which can be responsible for new critical factors and
solve the limitations of previous strategic management models.
Preparation of strategic planning need more factors than introduced
in traditional models. The needed factors includes determining future
Critical Success Factors and competencies, defining key processes,
determining the maturity of the processes, considering all aspects of
the external environment etc. Description of aforementioned
requirements, the outcomes and their order is developing and
presenting the MABENA model-s road map in this paper. This study
presents a road map for strategic planning of the Iranian
organizations.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: The recent developments in computing and
communication technology permit to users to access multimedia
documents with variety of devices (PCs, PDAs, mobile phones...)
having heterogeneous capabilities. This diversification of supports
has trained the need to adapt multimedia documents according to
their execution contexts. A semantic framework for multimedia
document adaptation based on the conceptual neighborhood graphs
was proposed. In this framework, adapting consists on finding
another specification that satisfies the target constraints and which is
as close as possible from the initial document. In this paper, we
propose a new way of building the conceptual neighborhood graphs
to best preserve the proximity between the adapted and the original
documents and to deal with more elaborated relations models by
integrating the relations relaxation graphs that permit to handle the
delays and the distances defined within the relations.
Abstract: It is believed that DNA damaging toxic metabolites contributes to the development of different pathological conditions. To prevent harmful influence of toxic agents, cells developed number of protecting mechanisms, such as enzymatic reaction of detoxification of reactive metabolites and repair of DNA damage. The aim of the study was to examine the association between polymorphism of GSTT1/GSTM1 and XRCC1/3 genes and coronary artery disease (CAD) incidence. To examine a polymorphism of these genes in CAD susceptibility in patients and controls, PCR based genotyping assay was performed. For GST genes, frequency of GSTM1 null genotype among CAD affected group was significantly increased than in control group (P0.1). We found that neither XRCC1 Arg399Gln nor XRCC3 Thr241Met were associated with CAD risk. Obtained data suggests that GSTM1 null genotype carriers are more susceptible to CAD development.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: Possible advantages of technology in educational
context required the defining boundaries of formal and informal
learning. Increasing opportunity to ubiquitous learning by
technological support has revealed a question of how to discover
the potential of individuals in the spontaneous environments such as
social networks. This seems to be related with the question of what
purposes in social networks have been being used? Social networks
provide various advantages in educational context as collaboration,
knowledge sharing, common interests, active participation and
reflective thinking. As a consequence of these, the purpose of this
study is composed of proposing a new model that could determine
factors which effect adoption of social network applications for usage
in educational context. While developing a model proposal, the
existing adoption and diffusion models have been reviewed and they
are thought to be suitable on handling an original perspective instead
of using completely other diffusion or acceptance models because of
different natures of education from other organizations. In the
proposed model; social factors, perceived ease of use, perceived
usefulness and innovativeness are determined four direct constructs
that effect adoption process. Facilitating conditions, image,
subjective norms and community identity are incorporated to model
as antecedents of these direct four constructs.
Abstract: Perishable goods constitute a large portion of retailer inventory and lose value with time due to deterioration and/or obsolescence. Retailers dealing with such goods required considering the factors of short shelf life and the dependency of sales on inventory displayed in determining optimal procurement policy. Many retailers follow the practice of using two bins - primary bin sales fresh items at a list price and secondary bin sales unsold items at a discount price transferred from primary bin on attaining certain age. In this paper, mathematical models are developed for primary bin and for secondary bin that maximizes profit with decision variables of order quantities, optimal review period and optimal selling price at secondary bin. The demand rates in two bins are assumed to be deterministic and dependent on displayed inventory level, price and age but independent of each other. The validity of the model is shown by solving an example and the sensitivity analysis of the model is also reported.
Abstract: Commercial hydroxyapatite (HA) was reinforced by
adding 2, 5, and 10 wt % of 28.5%CaO-28.5%P2O5-38%Na2 O-
5%CaF2 based glass and then sintered. Although HA shows good
biocompatibility with the human body, its applications are limited to
non load-bearing areas and coatings due to its poor mechanical
properties. These mechanical properties can be improved
substantially with addition of glass ceramics by sintering. In this
study, the effects of sintering hydroxyapatite with above specified
phosphate glass additions are quantified. Each composition was
sintered over a range of temperatures. Scanning electron microscopy
and x-ray diffraction were used to characterize the microstructure and
phases of the composites. The density, microhardness, and
compressive strength were measured using Archimedes Principle,
Vickers Microhardness Tester (at 0.98 N), and Instron Universal
Testing Machine (cross speed of 0.5 mm/min) respectively. These
results were used to indicate which composition provided suitable
material for use in hard tissue replacement. Composites containing 10
wt % glass additions formed dense HA/TCP (tricalcium phosphate)
composite materials possessing good compressive strength and
hardness than HA. In-vitro bioactivity was assessed by evaluating
changes in pH and Ca2+ ion concentration of SBF-simulated body
fluid on immersion of these composites in it for two weeks.
Abstract: Housebuilders in England have been the target of numerous government policies in recent years promoting increased productivity and affordability. As a result, the housebuilding industry is currently faced with objectives to improve the affordability and sustainability of new homes whilst also increasing production rates to 240,000 per year by 2016.Yet amidst a faltering economic climate, the UK Government is forging ahead with the 'Code for Sustainable Homes', which includes stringent sustainable standards for all new homes and sets ambitious targets for the housebuilding industry, the culmination of which is the production of zero carbon homes by 2016.Great uncertainty exists amongst housebuilders as to the costs, benefits and risks of building zero carbon homes. This paper examines the key barriers to zero carbon homes from housebuilders- perspective. A comprehensive opinion on the challenges to deliver zero carbon homes is gathered through a questionnaire survey issued to the major housing developers in England. The study found that a number of cultural, legislative, and financial barriers stand in the way of the widespread construction of zero carbon homes. The study concludes with several recommendations to both the Government and the housebuilding industry to address the barriers that hinder a successful delivery of zero carbon homes in England.
Abstract: A numerical study on the influence of electroosmotic flow on analyte preconcentration by isotachophoresis ( ITP) is made. We consider that the double layer induced electroosmotic flow ( EOF) counterbalance the electrophoretic velocity and a stationary ITP stacked zones results. We solve the Navier-Stokes equations coupled with the Nernst-Planck equations to determine the local convective velocity and the preconcentration dynamics of ions. Our numerical algorithm is based on a finite volume method along with a secondorder upwind scheme. The present numerical algorithm can capture the the sharp boundaries of step-changes ( plateau mode) or zones of steep gradients ( peak mode) accurately. The convection of ions due to EOF reduces the resolution of the ITP transition zones and produces a dispersion in analyte zones. The role of the electrokinetic parameters which induces dispersion is analyzed. A one-dimensional model for the area-averaged concentrations based on the Taylor-Aristype effective diffusivity is found to be in good agreement with the computed solutions.