Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: A new low-voltage floating gate MOSFET (FGMOS)
based squarer using square law characteristic of the FGMOS is
proposed in this paper. The major advantages of the squarer are simplicity,
rail-to-rail input dynamic range, low total harmonic distortion,
and low power consumption. The proposed circuit is biased without
body effect. The circuit is designed and simulated using SPICE in
0.25μm CMOS technology. The squarer is operated at the supply
voltages of ±0.75V . The total harmonic distortion (THD) for the
input signal 0.75Vpp at 25 KHz, and maximum power consumption
were found to be less than 1% and 319μW respectively.
Abstract: In this study, aerobic digestion of tannery industry
wastewater was carried out using mixed culture obtained from
common effluent treatment plant treating tannery wastewater. The
effect of pH, temperature, inoculum concentration, agitation speed
and initial substrate concentration on the reduction of organic matters
were found. The optimum conditions for COD reduction was found
to be pH - 7 (60%), temperature - 30ÔùªC (61%), inoculum
concentration - 2% (61%), agitation speed - 150rpm (65%) and initial
substrate concentration - 1560 mg COD/L (74%). Kinetics studies
were carried by using Monod model, First order, Diffusional model
and Singh model. From the results it was found that the Monod
model suits well for the degradation of tannery wastewater using
mixed microbial consortium.
Abstract: One of the long standing challenging aspect in mobile robotics is the ability to navigate autonomously, avoiding modeled and unmodeled obstacles especially in crowded and unpredictably changing environment. A successful way of structuring the navigation task in order to deal with the problem is within behavior based navigation approaches. In this study, Issues of individual behavior design and action coordination of the behaviors will be addressed using fuzzy logic. A layered approach is employed in this work in which a supervision layer based on the context makes a decision as to which behavior(s) to process (activate) rather than processing all behavior(s) and then blending the appropriate ones, as a result time and computational resources are saved.
Abstract: Large scale systems such as computational Grid is
a distributed computing infrastructure that can provide globally
available network resources. The evolution of information processing
systems in Data Grid is characterized by a strong decentralization of
data in several fields whose objective is to ensure the availability and
the reliability of the data in the reason to provide a fault tolerance
and scalability, which cannot be possible only with the use of the
techniques of replication. Unfortunately the use of these techniques
has a height cost, because it is necessary to maintain consistency
between the distributed data. Nevertheless, to agree to live with
certain imperfections can improve the performance of the system by
improving competition. In this paper, we propose a multi-layer protocol
combining the pessimistic and optimistic approaches conceived
for the data consistency maintenance in large scale systems. Our
approach is based on a hierarchical representation model with tree
layers, whose objective is with double vocation, because it initially
makes it possible to reduce response times compared to completely
pessimistic approach and it the second time to improve the quality
of service compared to an optimistic approach.
Abstract: Power Spectral Density (PSD) of quasi-stationary processes can be efficiently estimated using the short time Fourier series (STFT). In this paper, an algorithm has been proposed that computes the PSD of quasi-stationary process efficiently using offline autoregressive model order estimation algorithm, recursive parameter estimation technique and modified sliding window discrete Fourier Transform algorithm. The main difference in this algorithm and STFT is that the sliding window (SW) and window for spectral estimation (WSA) are separately defined. WSA is updated and its PSD is computed only when change in statistics is detected in the SW. The computational complexity of the proposed algorithm is found to be lesser than that for standard STFT technique.
Abstract: This paper presents the idea of a rough controller with application to control the overhead traveling crane system. The structure of such a controller is based on a suggested concept of a fuzzy logic controller. A measure of fuzziness in rough sets is introduced. A comparison between fuzzy logic controller and rough controller has been demonstrated. The results of a simulation comparing the performance of both controllers are shown. From these results we infer that the performance of the proposed rough controller is satisfactory.
Abstract: In this research, CaO-ZnO catalysts (with various
Ca:Zn atomic ratios of 1:5, 1:3, 1:1, and 3:1) prepared by incipientwetness
impregnation (IWI) and co-precipitation (CP) methods were
used as a catalyst in the transesterification of palm oil with methanol
for biodiesel production. The catalysts were characterized by several
techniques, including BET method, CO2-TPD, and Hemmett
Indicator. The effects of precursor concentration, and calcination
temperature on the catalytic performance were studied under reaction
conditions of a 15:1 methanol to oil molar ratio, 6 wt% catalyst,
reaction temperature of 60°C, and reaction time of 8 h. At Ca:Zn
atomic ratio of 1:3 gave the highest FAME value owing to a basic
properties and surface area of the prepared catalyst.
Abstract: In developing a text-to-speech system, it is well
known that the accuracy of information extracted from a text is
crucial to produce high quality synthesized speech. In this paper, a
new scheme for converting text into its equivalent phonetic spelling
is introduced and developed. This method is applicable to many
applications in text to speech converting systems and has many
advantages over other methods. The proposed method can also
complement the other methods with a purpose of improving their
performance. The proposed method is a probabilistic model and is
based on Smooth Ergodic Hidden Markov Model. This model can be
considered as an extension to HMM. The proposed method is applied
to Persian language and its accuracy in converting text to speech
phonetics is evaluated using simulations.
Abstract: The wide increase and diffusion on telecommunication
technologies have caused a huge spread of electromagnetic sources
in most European Countries. Since the public is continuously being
exposed to electromagnetic radiation the possible health effects have
become the focus of population concerns. As a result, electromagnetic
field monitoring stations which control field strength in commercial
frequency bands are being placed on the flat roof of many buildings.
However there is no guidance on where to place them. This paper
presents an analysis of frequency, polarization and angles of incidence
of a plane wave which impinges on a flat roof security wall and its
dependence on electromagnetic field strength meters placement.
Abstract: In this paper, in addition to introducing good urban planning and its effects on globalization, some new methodologies in urban management and another urban aspects has been presented. Some new concerns in increasing of urban population , metropolitans and its relations on big problems has been focused in this paper. It is very important matter that future urban planning with based on globalization will be with full of basically changes in its management and perspectives.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: The purpose of this work is measurement of the
system presampling MTF of a variable resolution x-ray (VRX) CT
scanner. In this paper, we used the parameters of an actual VRX CT
scanner for simulation and study of effect of different focal spot sizes
on system presampling MTF by Monte Carlo method (GATE
simulation software). Focal spot size of 0.6 mm limited the spatial
resolution of the system to 5.5 cy/mm at incident angles of below 17º
for cell#1. By focal spot size of 0.3 mm the spatial resolution
increased up to 11 cy/mm and the limiting effect of focal spot size
appeared at incident angles of below 9º. The focal spot size of 0.3
mm could improve the spatial resolution to some extent but because
of magnification non-uniformity, there is a 10 cy/mm difference
between spatial resolution of cell#1 and cell#256. The focal spot size
of 0.1 mm acted as an ideal point source for this system. The spatial
resolution increased to more than 35 cy/mm and at all incident angles
the spatial resolution was a function of incident angle. By the way
focal spot size of 0.1 mm minimized the effect of magnification nonuniformity.
Abstract: The dental composites are preferably used as filling
materials due to their esthetic appearances. Nevertheless one of the
major problems, during the application of the dental composites, is
shape change named as “polymerisation shrinkage" affecting clinical
success of the dental restoration while photo-polymerisation.
Polymerisation shrinkage of composites arises basically from the
formation of a polymer due to the monomer transformation which
composes of an organic matrix phase. It was sought, throughout this
study, to detect and evaluate the structural polymerisation shrinkage
of prepared dental composites in order to optimize the effects of
various fillers included in hydroxyapatite (HA)-reinforced dental
composites and hence to find a means to modify the properties of
these dental composites prepared with defined parameters. As a
result, the shrinkage values of the experimental dental composites
were decreased by increasing the filler content of composites and the
composition of different fillers used had effect on the shrinkage of
the prepared composite systems.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: Aluminothermic rail welding was from the beginning
a great success because its low price even in 1895 in Germany. This
method is now, widely used all over the world for the railways
construction, maintenance and modernization. Instructions give you
guidelines for preparing papers for conferences or journals.
After 1989, the welding needs of the potentials beneficiaries
(Romanian Railways, Urban Transportation Companies) keep raise
because of the railways maintenance and modernization necessity.
The main materials that determine the Thermit (T) composition
result from manufacturing scraps all over the country. This can help
the environment by consuming these scraps.
The Romanian need for alumino-thermic welding is now by 11300
per year, and in a favourable economical environment, this amount
can reach 30000 units.
This paper tries to show the effect of two types of modifiers
introduced in the T composition on the structure and properties of an
alumino-thermic welding.
Abstract: Within the collaborative research center 666 a new
product development approach and the innovative manufacturing
method of linear flow splitting are being developed. So far the design process is supported by 3D-CAD models utilizing User Defined
Features in standard CAD-Systems. This paper now presents new
functions for generating 3D-models of integral sheet metal products with bifurcations using Siemens PLM NX 6. The emphasis is placed
on design and semi-automated insertion of User Defined Features.
Therefore User Defined Features for both, linear flow splitting
and its derivative linear bend splitting, were developed. In order to facilitate the modeling process, an application was developed
that guides through the insertion process. Its usability and dialog layout adapt known standard features. The work presented here has
significant implications on the quality, accurateness and efficiency of the product generation process of sheet metal products with higher
order bifurcations.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.
Abstract: Position based routing protocols are the kinds of
routing protocols, which they use of nodes location information,
instead of links information to routing. In position based routing
protocols, it supposed that the packet source node has position
information of itself and it's neighbors and packet destination node.
Greedy is a very important position based routing protocol. In one of
it's kinds, named MFR (Most Forward Within Radius), source node
or packet forwarder node, sends packet to one of it's neighbors with
most forward progress towards destination node (closest neighbor to
destination). Using distance deciding metric in Greedy to forward
packet to a neighbor node, is not suitable for all conditions. If closest
neighbor to destination node, has high speed, in comparison with
source node or intermediate packet forwarder node speed or has very
low remained battery power, then packet loss probability is
increased. Proposed strategy uses combination of metrics distancevelocity
similarity-power, to deciding about giving the packet to
which neighbor. Simulation results show that the proposed strategy
has lower lost packets average than Greedy, so it has more reliability.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.