Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: In this paper, we propose an automatic verification
technology of software patches for user virtual environments on IaaS
Cloud to decrease verification costs of patches. In these days, IaaS
services have been spread and many users can customize virtual
machines on IaaS Cloud like their own private servers. Regarding to
software patches of OS or middleware installed on virtual machines,
users need to adopt and verify these patches by themselves. This task
increases operation costs of users. Our proposed method replicates
user virtual environments, extracts verification test cases for user
virtual environments from test case DB, distributes patches to virtual
machines on replicated environments and conducts those test cases
automatically on replicated environments. We have implemented the
proposed method on OpenStack using Jenkins and confirmed the
feasibility. Using the implementation, we confirmed the effectiveness
of test case creation efforts by our proposed idea of 2-tier abstraction
of software functions and test cases. We also evaluated the automatic
verification performance of environment replications, test cases
extractions and test cases conductions.
Abstract: Vehicular Adhoc Network (VANET) is a new
technology which aims to ensure intelligent inter-vehicle
communications, seamless internet connectivity leading to improved
road safety, essential alerts, and access to comfort and entertainment.
VANET operations are hindered by mobile node’s (vehicles)
uncertain mobility. Routing algorithms use metrics to evaluate which
path is best for packets to travel. Metrics like path length (hop count),
delay, reliability, bandwidth, and load determine optimal route. The
proposed scheme exploits link quality, traffic density, and
intersections as routing metrics to determine next hop. This study
enhances Geographical Routing Protocol (GRP) using fuzzy
controllers while rules are optimized with Bee Swarm Optimization
(BSO). Simulations results are compared to conventional GRP.
Abstract: The organizations in the knowledge economy era have
recognized the importance of building knowledge assets for
sustainable growth and development. In comparison to other
industries, Information Technology (IT) enterprises, holds an edge in
developing an effective Knowledge Management (KM) programmethanks
to their in-house technological abilities. This paper tries to
study the various knowledge based incentive programmes and its
effect on Knowledge Sharing and Learning in the context of the
Indian IT sector. A conceptual model is developed linking KM
Incentives, Knowledge Sharing and Learning. A questionnaire study
is conducted to collect primary data from the knowledge workers of
the IT organizations located in India. The data was analysed using
Structural Equation Modeling using Partial Least Square method. The
results show a strong influence of knowledge management incentives
on knowledge sharing and an indirect influence on learning.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: The present article seeks to carry out along the lines of
interpretation of the recent Portuguese Constitutional Court case law
on the possibility of an employee to observe a worship day imposed
by religious beliefs. In this approach to the question, considerations
on the subject of the relationship between religious freedom and
labour relations will inevitably arise. We intend to draw conclusions
of practical application from the court decisions on the matter of
freedom of religion.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: Large-scale data stream analysis has become one of
the important business and research priorities lately. Social networks
like Twitter and other micro-blogging platforms hold an enormous
amount of data that is large in volume, velocity and variety.
Extracting valuable information and trends out of these data would
aid in a better understanding and decision-making. Multiple analysis
techniques are deployed for English content. Moreover, one of the
languages that produce a large amount of data over social networks
and is least analyzed is the Arabic language. The proposed paper is a
survey on the research efforts to analyze the Arabic content in
Twitter focusing on the tools and methods used to extract the
sentiments for the Arabic content on Twitter.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: Every machine plays roles of client and server
simultaneously in a peer-to-peer (P2P) network. Though a P2P
network has many advantages over traditional client-server models
regarding efficiency and fault-tolerance, it also faces additional
security threats. Users/IT administrators should be aware of risks
from malicious code propagation, downloaded content legality, and
P2P software’s vulnerabilities. Security and preventative measures
are a must to protect networks from potential sensitive information
leakage and security breaches. Bit Torrent is a popular and scalable
P2P file distribution mechanism which successfully distributes large
files quickly and efficiently without problems for origin server. Bit
Torrent achieved excellent upload utilization according to
measurement studies, but it also raised many questions as regards
utilization in settings, than those measuring, fairness, and Bit
Torrent’s mechanisms choice. This work proposed a block selection
technique using Fuzzy ACO with optimal rules selected using ACO.
Abstract: Agriculture is the backbone of economy of Pakistan
and cotton is the major agricultural export and supreme source of raw
fiber for our textile industry. To combat severe problems of insect
and weed, combination of three genes namely Cry1Ac, Cry2A and
EPSPS genes was transferred in locally cultivated cotton variety
MNH-786 with the use of Agrobacterium mediated genetic
transformation. The present study focused on the molecular screening
of transgenic cotton plants at T3 generation in order to confirm
integration and expression of all three genes (Cry1Ac, Cry2A and
EPSP synthase) into the cotton genome. Initially, glyphosate spray
assay was used for screening of transgenic cotton plants containing
EPSP synthase gene at T3 generation. Transgenic cotton plants which
were healthy and showed no damage on leaves were selected after 07
days of spray. For molecular analysis of transgenic cotton plants in
the laboratory, the genomic DNA of these transgenic cotton plants
were isolated and subjected to amplification of the three genes. Thus,
seventeen out of twenty (Cry1Ac gene), ten out of twenty (Cry2A
gene) and all twenty (EPSP synthase gene) were produced positive
amplification. On the base of PCR amplification, ten transgenic plant
samples were subjected to protein expression analysis through
ELISA. The results showed that eight out of ten plants were actively
expressing the three transgenes. Real-time PCR was also done to
quantify the mRNA expression levels of Cry1Ac and EPSP synthase
gene. Finally, eight plants were confirmed for the presence and active
expression of all three genes at T3 generation.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.
Abstract: This paper presents a method of hardening the 8051
micro-controller, able to assure reliable operation in the presence of
bit flips caused by radiation. Aiming at avoiding such faults in the
8051 micro-controller, Hamming code protection was used in its
SRAM memory and registers. A VHDL code has been used for this
hamming code protection.
Abstract: This paper seeks to analyse the benefits of big data
and more importantly the challenges it pose to the subject of privacy
and data protection. First, the nature of big data will be briefly
deliberated before presenting the potential of big data in the present
days. Afterwards, the issue of privacy and data protection is
highlighted before discussing the challenges of implementing this
issue in big data. In conclusion, the paper will put forward the debate
on the adequacy of the existing legal framework in protecting
personal data in the era of big data.
Abstract: Estimation of model parameters is necessary to predict
the behavior of a system. Model parameters are estimated using
optimization criteria. Most algorithms use historical data to estimate
model parameters. The known target values (actual) and the output
produced by the model are compared. The differences between the
two form the basis to estimate the parameters. In order to compare
different models developed using the same data different criteria are
used. The data obtained for short scale projects are used here. We
consider software effort estimation problem using radial basis
function network. The accuracy comparison is made using various
existing criteria for one and two predictors. Then, we propose a new
criterion based on linear least squares for evaluation and compared
the results of one and two predictors. We have considered another
data set and evaluated prediction accuracy using the new criterion.
The new criterion is easy to comprehend compared to single statistic.
Although software effort estimation is considered, this method is
applicable for any modeling and prediction.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: The paper deals with the diagnostics of steel roof
structure of the winter sports halls built in 1970 year. The necessity
of the diagnostics has been given by the requirement to the evaluation
design of this structure, which has been caused by the new situation
in the field of the loadings given by the validity of the European
Standards in the Czech Republic from 2010 year. Due to these
changes in the normative rules, in practice existing structures are
gradually subjected to the evaluation design and depending on its
results to the strengthening or reconstruction, respectively. Steel roof
is composed of plane truss main girders, purlins and bracings and the
roof structure is supported by two arch main girders with the span of
L = 84 m. The in situ diagnostics of the roof structure was oriented to
the following parts: (i) determination and evaluation of the actual
material properties of used steel and (ii) verification of the actual
dimensions of the structural members. For the solution the nondestructive
methods have been used for in situ measurement. For the
indicative determination of steel strengths the modified method based
on the determination of Rockwell’s hardness has been used. For the
verification of the member’s dimensions (thickness of hollow
sections) the ultrasound method has been used. This paper presents
the results obtained using these testing methods and their evaluation,
from the viewpoint of the usage for the subsequent static assessment
and design evaluation of the existing structure. For the comparison,
the examples of the similar evaluations realized for steel structures of
the stadiums in Olomouc and Jihlava cities are briefly illustrated, too.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: The inherent skin patterns created at the joints in the
finger exterior are referred as finger knuckle-print. It is exploited to
identify a person in a unique manner because the finger knuckle print
is greatly affluent in textures. In biometric system, the region of
interest is utilized for the feature extraction algorithm. In this paper,
local and global features are extracted separately. Fast Discrete
Orthonormal Stockwell Transform is exploited to extract the local
features. Global feature is attained by escalating the size of Fast
Discrete Orthonormal Stockwell Transform to infinity. Two features
are fused to increase the recognition accuracy. A matching distance is
calculated for both the features individually. Then two distances are
merged mutually to acquire the final matching distance. The
proposed scheme gives the better performance in terms of equal error
rate and correct recognition rate.