Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: The objective of the research was to study of foot
anthropometry of children aged 7-12 years in the South of Thailand Thirty-three dimensions were measured on 305 male and 295 female
subjects with 3 age ranges (7-12 years old). The instrumentation consists of four types of anthropometer, digital vernier caliper, digital
height gauge and measuring tape. The mean values and standard
deviations of average age, height, and weight of the male subjects were 9.52(±1.70) years, 137.80(±11.55) cm, and 37.57(±11.65) kg.
Female average age, height, and weight subjects were 9.53(±1.70) years, 137.88(±11.55) cm, and 34.90(±11.57) kg respectively. The
comparison of the 33 comparison measured anthropometric. Between
male and female subjects were sexual differences in size on women in almost all areas of significance (p
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: This study examined the effects of neuromuscular
training (NT) on limits of stability (LOS) in female individuals.
Twenty female basketball amateurs were assigned into NT
experimental group or control group by volunteer. All the players were
underwent regular basketball practice, 90 minutes, 3 times per week
for 6 weeks, but the NT experimental group underwent extra NT with
plyometric and core training, 50 minutes, 3 times per week for 6 weeks
during this period. Limits of stability (LOS) were evaluated by the
Biodex Balance System. One factor ANCOVA was used to examine
the differences between groups after training. The significant level for
statistic was set at p
Abstract: The increasing interest in plant sterol enriched foods
is due to the fact that they reduce blood cholesterol concentrations
without adverse side effects. In this context, enriched foods with
phytosterols may be helpful in protecting population against
atherosclerosis and cardiovascular diseases. The aim of the present
work was to evaluate in a population of Viseu, Portugal, the
consumption habits low-fat, plant sterol-enriched yoghurt. For this
study, 577 inquiries were made and the sample was randomly
selected for people shopping in various supermarkets. The
preliminary results showed that the biggest consumers of these
products were women aged 45 to 65 years old. Most of the people
who claimed to buy these products consumed them once a day. Also,
most of the consumers under antidyslipidemic therapeutics noticed
positive effects on hypercholesterolemia.
Abstract: The manufacture of large-scale precision aerospace
components using CNC requires a highly effective maintenance
strategy to ensure that the required accuracy can be achieved over
many hours of production. This paper reviews a strategy for a
maintenance management system based on Failure Mode Avoidance,
which uses advanced techniques and technologies to underpin a
predictive maintenance strategy. It is shown how condition
monitoring (CM) is important to predict potential failures in high
precision machining facilities and achieve intelligent and integrated
maintenance management. There are two distinct ways in which CM
can be applied. One is to monitor key process parameters and
observe trends which may indicate a gradual deterioration of
accuracy in the product. The other is the use of CM techniques to
monitor high status machine parameters enables trends to be
observed which can be corrected before machine failure and
downtime occurs.
It is concluded that the key to developing a flexible and intelligent
maintenance framework in any precision manufacturing operation is
the ability to evaluate reliably and routinely machine tool condition
using condition monitoring techniques within a framework of Failure
Mode Avoidance.
Abstract: To minimize power losses, it is important to
determine the location and size of local generators to be placed in
unbalanced power distribution systems. On account of some inherent
features of unbalanced distribution systems, such as radial structure,
large number of nodes, a wide range of X/R ratios, the conventional
techniques developed for the transmission systems generally fail on
the determination of optimum size and location of distributed
generators (DGs). This paper presents a simple method for
investigating the problem of contemporaneously choosing best
location and size of DG in three-phase unbalanced radial distribution
system (URDS) for power loss minimization and to improve the
voltage profile of the system. Best location of the DG is determined
by using voltage index analysis and size of DG is computed by
variational technique algorithm according to available standard size
of DGs. This paper presents the results of simulations for 25-bus and
IEEE 37- bus Unbalanced Radial Distribution system.
Abstract: This study examined the effects of eight weeks of
whole-body vibration training (WBVT) on vertical and decuple jump
performance in handball athletes. Sixteen collegiate Level I handball
athletes volunteered for this study. They were divided equally as
control group and experimental group (EG). During the period of the
study, all athletes underwent the same handball specific training, but
the EG received additional WBVT (amplitude: 2 mm, frequency: 20 -
40 Hz) three time per week for eight consecutive weeks. The vertical
jump performance was evaluated according to the maximum height of
squat jump (SJ) and countermovement jump (CMJ). Single factor
ANCOVA was used to examine the differences in each parameter
between the groups after training with the pretest values as a covariate.
The statistic significance was set at p < .05. After 8 weeks WBVT, the
EG had significantly improved the maximal height of SJ (40.92 ± 2.96
cm vs. 48.40 ± 4.70 cm, F = 5.14, p < .05) and the maximal height
CMJ (47.25 ± 7.48 cm vs. 52.20 ± 6.25 cm, F = 5.31, p < .05). 8 weeks
of additional WBVT could improve the vertical and decuple jump
performance in handball athletes. Enhanced motor unit
synchronization and firing rates, facilitated muscular contraction
stretch-shortening cycle, and improved lower extremity
neuromuscular coordination could account for these enhancements.
Abstract: Tensile armour wires provide a flexible pipe's
resistance to longitudinal stresses. Flexible pipe manufacturers need
to know the effect of defects such as scratches and cracks, with
dimensions less than 0.2mm which is the limit of the current nondestructive
detection technology, on the fracture stress and fracture
strain of the wire for quality assurance purposes. Recent research
involving the determination of the fracture strength of cracked wires
employed laboratory testing and classical fracture mechanics
approach using non-standardised fracture mechanics specimens
because standard test specimens could not be manufactured from the
wires owing to their sizes. In this work, the effect of miniature
cracks on the fracture properties of tensile armour wires was
investigated using laboratory and finite element tensile testing
simulations with the phenomenological shear fracture model. The
investigation revealed that the presence of cracks shallower than
0.2mm is worse on the fracture strain of the wire.
Abstract: Future space vehicles will require the use of non-toxic, cryogenic propellants, because of the performance advantages over the toxic hypergolic propellants and also because of the environmental and handling concerns. A prototypical capillary flow liquid acquisition device (LAD) for cryogenic propellants was fabricated with a mesh screen, covering a rectangular flow channel with a cylindrical outlet tube, and was tested with liquid oxygen (LOX). In order to better understand the performance in various gravity environments and orientations with different submersion depths of the LAD, a series of computational fluid dynamics (CFD) simulations of LOX flow through the LAD screen channel, including horizontally and vertically submersions of the LAD channel assembly at normal gravity environment was conducted. Gravity effects on the flow field in LAD channel are inspected and analyzed through comparing the simulations.
Abstract: This study was conducted to evaluate factors
regulating groundwater quality in an area with agriculture as main
use. Under this study twelve groundwater samples have been
collected from Padra taluka, Dabhoi taluka and Savli taluka of
Vadodara district. Groundwater samples were chemically analyzed
for major physicochemical parameter in order to understand the
different geochemical processes affecting the groundwater quality.
The analytical results shows higher concentration of total dissolved
solids (16.67%), electrical conductivity (25%) and magnesium
(8.33%) for pre monsoon and total dissolved solids (16.67%),
electrical conductivity (33.3%) and magnesium (8.33%) for post
monsoon which indicates signs of deterioration as per WHO and BIS
standards. On the other hand, 50% groundwater sample is unsuitable
for irrigation purposes based on irrigation quality parameters. The
study revealed that application of fertilizer for agricultural
contributing the higher concentration of ions in aquifer of Vadodara
district.
Abstract: Road signs are the elements of roads with a lot of
influence in driver-s behavior. So that signals can fulfill its function,
they must overcome visibility and durability requirements,
particularly needed at night, when the coefficient of retroreflection
becomes a decisive factor in ensuring road safety. Accepting that the
visibility of the signage has implications for people-s safety, we
understand the importance to fulfill its function: to foster the highest
standards of service and safety in drivers. The usual conditions of
perception of any sign are determined by: age of the driver, reflective
material, luminosity, vehicle speed and emplacement. In this way,
this paper evaluates the different signals to increase the safety road.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: Excilamps are new UV sources with great potential
for application in wastewater treatment. In the present work, a XeBr
excilamp emitting radiation at 283 nm has been used for the
photodegradation of 4-chlorophenol within a range of concentrations
from 50 to 500 mg L-1. Total removal of 4-chlorophenol was
achieved for all concentrations assayed. The two main photoproduct
intermediates formed along the photodegradation process,
benzoquinone and hydroquinone, although not being completely
removed, remain at very low residual concentrations. Such
concentrations are insignificant compared to the 4-chlorophenol
initial ones and non-toxic. In order to simulate the process and scaleup,
a kinetic model has been developed and validated from the
experimental data.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: Stochastic modeling of network traffic is an area of
significant research activity for current and future broadband
communication networks. Multimedia traffic is statistically
characterized by a bursty variable bit rate (VBR) profile. In this
paper, we develop an improved model for uniform activity level
video sources in ATM using a doubly stochastic autoregressive
model driven by an underlying spatial point process. We then
examine a number of burstiness metrics such as the peak-to-average
ratio (PAR), the temporal autocovariance function (ACF) and the
traffic measurements histogram. We found that the former measure is
most suitable for capturing the burstiness of single scene video
traffic. In the last phase of this work, we analyse statistical
multiplexing of several constant scene video sources. This proved,
expectedly, to be advantageous with respect to reducing the
burstiness of the traffic, as long as the sources are statistically
independent. We observed that the burstiness was rapidly
diminishing, with the largest gain occuring when only around 5
sources are multiplexed. The novel model used in this paper for
characterizing uniform activity video was thus found to be an
accurate model.
Abstract: In this paper usefulness of quasi-Newton iteration
procedure in parameters estimation of the conditional variance
equation within BHHH algorithm is presented. Analytical solution of
maximization of the likelihood function using first and second
derivatives is too complex when the variance is time-varying. The
advantage of BHHH algorithm in comparison to the other
optimization algorithms is that requires no third derivatives with
assured convergence. To simplify optimization procedure BHHH
algorithm uses the approximation of the matrix of second derivatives
according to information identity. However, parameters estimation in
a/symmetric GARCH(1,1) model assuming normal distribution of
returns is not that simple, i.e. it is difficult to solve it analytically.
Maximum of the likelihood function can be founded by iteration
procedure until no further increase can be found. Because the
solutions of the numerical optimization are very sensitive to the
initial values, GARCH(1,1) model starting parameters are defined.
The number of iterations can be reduced using starting values close
to the global maximum. Optimization procedure will be illustrated in
framework of modeling volatility on daily basis of the most liquid
stocks on Croatian capital market: Podravka stocks (food industry),
Petrokemija stocks (fertilizer industry) and Ericsson Nikola Tesla
stocks (information-s-communications industry).