Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: In this research, TRACE model of Chinshan BWR/4
nuclear power plant (NPP) has been developed for the simulation and
analysis of ultimate response guideline (URG).The main actions of
URG are the depressurization and low pressure water injection of
reactor and containment venting. This research focuses to verify the
URG efficiency under Fukushima-like conditions. TRACE analysis
results show that the URG can keep the PCT below the criteria
1088.7 K under Fukushima-like conditions. It indicated that Chinshan
NPP was safe.
Abstract: Froth flotation remains to date as one of the most used
metallurgical processes for concentrating metal-bearing minerals in
ores. Oxide ores are relatively less amenable to froth flotation and
require a judicious choice of reagents for the recovery of metals to be
optimised. Laboratory batch flotation tests were conducted to
determine the effect of two types of gasoil-rinkalore mixtures on the
flotation response of a copper cobalt oxide ore sample. The head
assay conducted on the initial ore sample showed that it contained
about 2.90% of Cu, 0.12% of Co.
Upon the flotation test work, the results obtained indicated that the
concentrate obtained with use of the mixture gazoil-rinkalore RX
yielded 8.24% Cu and 0.22% Co concentrate grades with recoveries
of 76.0% Cu and 78.0% Co respectively. But, the concentrate
obtained by use of the mixture gazoil-rinkalore RX3 yielded
relatively bad results with 5.92% Cu and 0.18% Cu concentrate
grades with recoveries of 70.3% Cu and 65.3% Co respectively.
Abstract: Through use of novel modern/rapid processing
techniques such as screen printing and Near-Infrared (NIR) radiative
curing, process time for the sintering of sintered nickel plaques,
applicable to alkaline nickel battery chemistries, has been drastically
reduced from in excess of 200 minutes with conventional convection
methods to below 2 minutes using NIR curing methods. Steps have
also been taken to remove the need for forming gas as a reducing
agent by implementing carbon as an in-situ reducing agent, within the
ink formulation.
Abstract: The article proposed intends to analyze the possibility
(and conditions) of a media regulation law in a democratic rule of law
in the twenty-first century. To do so, will be presented initially the
idea of the public sphere (by Jürgen Habermas), showing how it is
presented as an interface between the citizen and the state (or the
private and public) and how important is it in a deliberative
democracy. Based on this paradigm, the traditional perception of the
role of public information (such as system functional element) and on
the possibility of media regulation will be exposed, due to the public
nature of their activity. A critical argument will then be displayed
from two different perspectives: a) the formal function of the current
media information, considering that the digital age has fragmented
the information access; b) the concept of a constructive democracy,
which reduces the need for representation, changing the strategic
importance of the public sphere. The question to be addressed (based
on the comparative law) is if the regulation is justified in a
polycentric democracy, especially when it operates under the digital
age (with immediate and virtual communication). The proposal is to
be presented in the sense that even in a twenty-first century the media
in a democratic rule of law still has an extremely important role and
may be subject to regulation, but this should be on terms very
different (and narrower) from those usually defended.
Abstract: Transportation of long turbine blades from one place
to another is a difficult process. Hence a feasibility study of
modularization of wind turbine blade was taken from structural
standpoint through finite element analysis. Initially, a non-segmented
blade is modeled and its structural behavior is evaluated to serve as
reference. The resonant, static bending and fatigue tests are simulated
in accordance with IEC61400-23 standard for comparison purpose.
The non-segmented test blade is separated at suitable location based
on trade off studies and the segments are joined with an innovative
double strap bonded joint configuration. The adhesive joint is
modeled by adopting cohesive zone modeling approach in ANSYS.
The developed blade model is analyzed for its structural response
through simulation. Performances of both the blades are found to be
similar, which indicates that, efficient segmentation of the long blade
is possible which facilitates easy transportation of the blades and on
site reassembling. The location selected for segmentation and
adopted joint configuration has resulted in an efficient segmented
blade model which proves the methodology adopted for segmentation
was quite effective. The developed segmented blade appears to be the
viable alternative considering its structural response specifically in
fatigue within considered assumptions.
Abstract: Fabric textures are very common in our daily life.
However, the representation of fabric textures has never been explored
from neuroscience view. Theoretical studies suggest that primary
visual cortex (V1) uses a sparse code to efficiently represent natural
images. However, how the simple cells in V1 encode the artificial
textures is still a mystery. So, here we will take fabric texture as
stimulus to study the response of independent component analysis that
is established to model the receptive field of simple cells in V1. We
choose 140 types of fabrics to get the classical fabric textures as
materials. Experiment results indicate that the receptive fields of
simple cells have obvious selectivity in orientation, frequency and
phase when drifting gratings are used to determine their tuning
properties. Additionally, the distribution of optimal orientation and
frequency shows that the patch size selected from each original fabric
image has a significant effect on the frequency selectivity.
Abstract: The aim of the current study was to develop and
validate a Response to Stressful Situations Scale (RSSS) for the
Portuguese population. This scale assesses the degree of stress
experienced in scenarios that can constitute positive, negative and
more neutral stressors, and also describes the physiological,
emotional and behavioral reactions to those events according to their
intensity. These scenarios include typical stressor scenarios relevant
to patients with schizophrenia, which are currently absent from most
scales, assessing specific risks that these stressors may bring on
subjects, which may prove useful in non-clinical and clinical
populations (i.e. Patients with mood or anxiety disorders,
schizophrenia). Results from Principal Components Analysis and
Confirmatory Factor Analysis of two adult samples from general
population allowed to confirm a three-factor model with good fit
indices: χ2 (144)= 370.211, p = 0.000; GFI = 0.928; CFI = 0.927; TLI =
0.914, RMSEA = 0.055, P(rmsea ≤0.005) = .096; PCFI = .781.
Further data analysis of the scale revealed that RSSS is an adequate
assessment tool of stress response in adults to be used in further
research and clinical settings, with good psychometric characteristics,
adequate divergent and convergent validity, good temporal stability
and high internal consistency.
Abstract: A comprehensive CFD model is developed to
represent heterogeneous combustion and two burner designs of
supply sugar-cane bagasse into a furnace. The objective of this work
is to compare the insertion and burning of a Brazilian south-eastern
sugar-cane bagasse using a new swirl burner design against an actual
geometry under operation. The new design allows control the
particles penetration and scattering inside furnace by adjustment of
axial/tangential contributions of air feed without change their mass
flow. The model considers turbulence using RNG k-, combustion
using EDM, radiation heat transfer using DTM with 16 ray directions
and bagasse particle tracking represented by Schiller-Naumann
model. The obtained results are favorable to use of new design swirl
burner because its axial/tangential control promotes more penetration
or more scattering than actual design and allows reproduce the actual
design operation without change the overall mass flow supply.
Abstract: Press-hardened profiles are used e.g. for automotive
applications in order to improve light weight construction due to the
high reachable strength. The application of interior water-air spray
cooling contributes to significantly reducing the cycle time in the
production of heat-treated tubes. This paper describes a new
manufacturing method for producing press-hardened hollow profiles
by means of an additional interior cooling based on a water-air spray.
Furthermore, this paper provides the results of thorough
investigations on the properties of press-hardened tubes in
dependence of varying spray parameters.
Abstract: In this work, two fermentations at different
temperatures (25 and 30ºC), with cell recycling, were accomplished
to produce ethanol, using a mix of commercial substrates, xylose
(70%) and glucose (30%), as organic source for Scheffersomyces
stipitis. Five consecutive fermentations of 80 g L-1 (1º, 2º and 3º
recycles), 96 g L-1 (4º recycle) and 120 g L-1 (5º recycle)reduced
sugars led to a final maximum ethanol concentration of 17.2 and 34.5
g L-1, at 25 and 30ºC, respectively. Glucose was the preferred
substrate; moreover xylose startup degradation was initiated after a
remaining glucose presence in the medium. Results showed that yeast
acid treatment, performed before each cycle, provided improvements
on cell viability, accompanied by ethanol productivity of 2.16 g L-1 h-
1 at 30ºC. A maximum 36% of xylose was retained in the
fermentation medium and after five-cycle fermentation an ethanol
yield of 0.43 g ethanol/g sugars was observed. S. stipitis fermentation
capacity and tolerance showed better results at 30ºC with 83.4% of
theoretical yield referenced on initial biomass.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: The effect of N2 pretreatment on the catalytic activity
of tungsten-based catalysts was investigated in the metathesis of
ethylene and trans-2-butene at 450oC and atmospheric pressure. The
presence of tungsten active species was confirmed by UV-Vis and
Raman spectroscopy. Compared to the WO3-based catalysts treated
in air, higher amount of WO4 2-tetrahedral species and lower amount
of WO3 crystalline species were observed on the N2-treated ones.
These contribute to the higher conversion of 2-butene and propylene
selectivity during 10 h time-on-stream. Moreover, N2 treatment led to
lower amount of coke formation as revealed by TPO of the spent
catalysts.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: This paper shows in detail the mathematical model of
direct and inverse kinematics for a robot manipulator (welding type)
with four degrees of freedom. Using the D-H parameters, screw
theory, numerical, geometric and interpolation methods, the
theoretical and practical values of the position of robot were
determined using an optimized algorithm for inverse kinematics
obtaining the values of the particular joints in order to determine the
virtual paths in a relatively short time.
Abstract: The advent of social networking technologies has been
met with mixed reactions in academic and corporate circles around
the world. This study explored the influence of social network in
current era, the relation being maintained between the Social
networking site and its user by the extent of use, benefits and latest
technologies. The study followed a descriptive research design
wherein a questionnaire was used as the main research tool. The data
collected was analyzed using SPSS 16. Data was gathered from 1205
users and analyzed in accordance with the objectives of the study.
The analysis of the results seem to suggest that the majority of users
were mainly using Facebook, despite of concerns raised about the
disclosure of personal information on social network sites, users
continue to disclose huge quantity of personal information, they find
that reading privacy policy is time consuming and changes made can
result into improper settings.
Abstract: Non contact evaluation of the thickness of paint
coatings can be attempted by different destructive and nondestructive
methods such as cross-section microscopy, gravimetric mass
measurement, magnetic gauges, Eddy current, ultrasound or
terahertz. Infrared thermography is a nondestructive and non-invasive
method that can be envisaged as a useful tool to measure the surface
thickness variations by analyzing the temperature response. In this
paper, the thermal quadrupole method for two layered samples heated
up with a pulsed excitation is firstly used. By analyzing the thermal
responses as a function of thermal properties and thicknesses of both
layers, optimal parameters for the excitation source can be identified.
Simulations show that a pulsed excitation with duration of ten
milliseconds allows obtaining a substrate-independent thermal
response. Based on this result, an experimental setup consisting of a
near-infrared laser diode and an Infrared camera was next used to
evaluate the variation of paint coating thickness between 60 μm and
130 μm on two samples. Results show that the parameters extracted
for thermal images are correlated with the estimated thicknesses by
the Eddy current methods. The laser pulsed thermography is thus an
interesting alternative nondestructive method that can be moreover
used for nonconductive substrates.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: Cesium iodide (CsI) melt was injected into anodic aluminum oxide (AAO) template and was solidified to CsI column. The controllable AAO channel size (10~500 nm) can makes CsI column size from 10 to 500 nm in diameter. In order to have a shorter light irradiate from each singe CsI column top to bottom the AAO template was coated a TiO2 nano-film. The TiO2 film acts a refraction film and makes X-ray has a shorter irradiation path in the CsI crystal making a stronger the photo-electron signal. When the incidence light irradiate from air (R=1.0) to CsI’s first surface (R=1.84) the first refraction happen, the first refraction continue into TiO2 film (R=2.88) and produces the low angle of the second refraction. Then the second refraction continue into AAO wall (R=1.78) and produces the third refraction after refractions between CsI and AAO wall (R=1.78) produce the fourth refraction. The incidence light through TiO2 filmand the first surface of CsI then arrive to the second surface of CsI. Therefore, the TiO2 film can has shorter refraction path of incidence light and increase the photo-electron conversion efficiency.