Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: Dengue virus is transmitted from person to person
through the biting of infected Aedes Aegypti mosquitoes. DEN-1,
DEN-2, DEN-3 and DEN-4 are four serotypes of this virus. Infection
with one of these four serotypes apparently produces permanent
immunity to it, but only temporary cross immunity to the others. The
length of time during incubation of dengue virus in human and
mosquito are considered in this study. The dengue patients are
classified into infected and infectious classes. The infectious human
can transmit dengue virus to susceptible mosquitoes but infected
human can not. The transmission model of this disease is formulated.
The human population is divided into susceptible, infected, infectious
and recovered classes. The mosquito population is separated into
susceptible, infected and infectious classes. Only infectious
mosquitoes can transmit dengue virus to the susceptible human. We
analyze this model by using dynamical analysis method. The
threshold condition is discussed to reduce the outbreak of this
disease.
Abstract: In this paper, a novel method for recognition of musical
instruments in a polyphonic music is presented by using an
embedded hidden Markov model (EHMM). EHMM is a doubly
embedded HMM structure where each state of the external HMM
is an independent HMM. The classification is accomplished for
two different internal HMM structures where GMMs are used as
likelihood estimators for the internal HMMs. The results are compared
to those achieved by an artificial neural network with two
hidden layers. Appropriate classification accuracies were achieved
both for solo instrument performance and instrument combinations
which demonstrates that the new approach outperforms the similar
classification methods by means of the dynamic of the signal.
Abstract: Certain tRNA synthetases have developed highly accurate molecular machinery to discriminate their cognate amino acids. Those aaRSs achieve their goal via editing reaction in the Connective Polypeptide 1 (CP1). Recently mutagenesis studies have revealed the critical importance of residues in the CP1 domain for editing activity and X-ray structures have shown binding mode of noncognate amino acids in the editing domain. To pursue molecular mechanism for amino acid discrimination, molecular modeling studies were performed. Our results suggest that aaRS bind the noncognate amino acid more tightly than the cognate one. Finally, by comparing binding conformations of the amino acids in three systems, the amino acid binding mode was elucidated and a discrimination mechanism proposed. The results strongly reveal that the conserved threonines are responsible for amino acid discrimination. This is achieved through side chain interactions between T252 and T247/T248 as well as between those threonines and the incoming amino acids.
Abstract: The link between coordinate transformations in the plane and their effects on the graph of a function can be difficult for students studying college level mathematics to comprehend. To solidify this conceptual link in the mind of a student Microsoft Excel can serve as a convenient graphing tool and pedagogical aid. The authors of this paper describe how various transformations and their related functional symmetry properties can be graphically displayed with an Excel spreadsheet.
Abstract: This paper mainly studies the analyses of parameters
in the intersection collision avoidance (ICA) system based on the radar
sensors. The parameters include the positioning errors, the repeat
period of the radar sensor, the conditions of potential collisions of two
cross-path vehicles, etc. The analyses of the parameters can provide
the requirements, limitations, or specifications of this ICA system. In
these analyses, the positioning errors will be increased as the measured
vehicle approach the intersection. In addition, it is not necessary to
implement the radar sensor in higher position since the positioning
sensitivities become serious as the height of the radar sensor increases.
A concept of the safety buffer distances for front and rear of the
measured vehicle is also proposed. The conditions for potential
collisions of two cross-path vehicles are also presented to facilitate the
computation algorithm.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: Organizational culture fosters innovation, and
innovation is the main engine to be sustained within the uncertainty
market. Like other countries, the construction industry significantly
contributes to the economy, society and technology of Malaysia, yet,
innovation is still considered slow compared to other industries such
as manufacturing. Given the important role of an architect as the key
player and the contributor of new ideas in the construction industry,
there is a call to identify the issue and improve the current situation
by focusing on the architectural firms. In addition, the existing
studies tend to focus only on a few dimensions of organizational
culture and very few studies consider whether innovation is being
generated or adopted. Hence, the present research tends to fill in the
gap by identifying the organizational cultures that foster or hinder
innovation generation and/or innovation adoption, and propose a
model of organizational culture and innovation generation and/or
adoption.
Abstract: In this paper, low end Digital Signal Processors (DSPs)
are applied to accelerate integer neural networks. The use of DSPs
to accelerate neural networks has been a topic of study for some
time, and has demonstrated significant performance improvements.
Recently, work has been done on integer only neural networks, which
greatly reduces hardware requirements, and thus allows for cheaper
hardware implementation. DSPs with Arithmetic Logic Units (ALUs)
that support floating or fixed point arithmetic are generally more
expensive than their integer only counterparts due to increased circuit
complexity. However if the need for floating or fixed point math
operation can be removed, then simpler, lower cost DSPs can be
used. To achieve this, an integer only neural network is created in
this paper, which is then accelerated by using DSP instructions to
improve performance.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.
Abstract: An economic operation scheduling problem of a
hydro-thermal power generation system has been properly solved by
the proposed multipath adaptive tabu search algorithm (MATS). Four
reservoirs with their own hydro plants and another one thermal plant
are integrated to be a studied system used to formulate the objective
function under complicated constraints, eg water managements,
power balance and thermal generator limits. MATS with four subsearch
units (ATSs) and two stages of discarding mechanism (DM),
has been setting and trying to solve the problem through 25 trials
under function evaluation criterion. It is shown that MATS can
provide superior results with respect to single ATS and other
previous methods, genetic algorithms (GA) and differential evolution
(DE).
Abstract: Intelligent deep-drawing is an instrumental research field in sheet metal forming. A set of 28 different experimental data have been employed in this paper, investigating the roles of die radius, punch radius, friction coefficients and drawing ratios for axisymmetric workpieces deep drawing. This paper focuses an evolutionary neural network, specifically, error back propagation in collaboration with genetic algorithm. The neural network encompasses a number of different functional nodes defined through the established principles. The input parameters, i.e., punch radii, die radii, friction coefficients and drawing ratios are set to the network; thereafter, the material outputs at two critical points are accurately calculated. The output of the network is used to establish the best parameters leading to the most uniform thickness in the product via the genetic algorithm. This research achieved satisfactory results based on demonstration of neural networks.
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: Advancement in Artificial Intelligence has lead to the
developments of various “smart" devices. Character recognition
device is one of such smart devices that acquire partial human
intelligence with the ability to capture and recognize various
characters in different languages. Firstly multiscale neural training
with modifications in the input training vectors is adopted in this
paper to acquire its advantage in training higher resolution character
images. Secondly selective thresholding using minimum distance
technique is proposed to be used to increase the level of accuracy of
character recognition. A simulator program (a GUI) is designed in
such a way that the characters can be located on any spot on the
blank paper in which the characters are written. The results show that
such methods with moderate level of training epochs can produce
accuracies of at least 85% and more for handwritten upper case
English characters and numerals.
Abstract: Modern information and communication technologies
offer a variety of support options for the efficient handling of
customer relationships. CRM systems have been developed, which
are designed to support the processes in the areas of marketing, sales
and service. Along with technological progress, CRM systems are
constantly changing, i.e. the systems are continually enhanced by
new functions. However, not all functions are suitable for every
company because of different frameworks and business processes. In
this context the question arises whether or not CRM systems are
widely used in Austrian companies and which business processes are
most frequently supported by CRM systems. This paper aims to shed
light on the popularity of CRM systems in Austrian companies in
general and the use of different functions to support their daily
business. First of all, the paper provides a theoretical overview of the
structure of modern CRM systems and proposes a categorization of
currently available software functionality for collaborative,
operational and analytical CRM processes, which provides the
theoretical background for the empirical study. Apart from these
theoretical considerations, the paper presents the empirical results of
a field survey on the use of CRM systems in Austrian companies and
analyzes its findings.
Abstract: This paper aims to present the reviews of the
application of neural network in shunt active power filter (SAPF).
From the review, three out of four components of SAPF structure,
which are harmonic detection component, compensating current
control, and DC bus voltage control, have been adopted some of
neural network architecture as part of its component or even
substitution. The objectives of most papers in using neural network in
SAPF are to increase the efficiency, stability, accuracy, robustness,
tracking ability of the systems of each component. Moreover,
minimizing unneeded signal due to the distortion is the ultimate goal
in applying neural network to the SAPF. The most famous
architecture of neural network in SAPF applications are ADALINE
and Backpropagation (BP).
Abstract: From a set of shifted, blurred, and decimated image , super-resolution image reconstruction can get a high-resolution image. So it has become an active research branch in the field of image restoration. In general, super-resolution image restoration is an ill-posed problem. Prior knowledge about the image can be combined to make the problem well-posed, which contributes to some regularization methods. In the regularization methods at present, however, regularization parameter was selected by experience in some cases and other techniques have too heavy computation cost for computing the parameter. In this paper, we construct a new super-resolution algorithm by transforming the solving of the System stem Є=An into the solving of the equations X+A*X-1A=I , and propose an inverse iterative method.