Abstract: A co-generation system in automobile can improve
thermal efficiency of vehicle in some degree. The waste heat from the
engine exhaust and coolant is still attractive energy source that reaches
around 60% of the total energy converted from fuel. To maximize the
effectiveness of heat exchangers for recovering the waste heat, it is
vital to select the most suitable working fluid for the system, not to
mention that it is important to find the optimum design for the heat
exchangers. The design of heat exchanger is out of scoop of this study;
rather, the main focus has been on the right selection of working fluid
for the co-generation system. Simulation study was carried out to find
the most suitable working fluid that can allow the system to achieve
the optimum efficiency in terms of the heat recovery rate and thermal
efficiency.
Abstract: This paper presents the benchmarking results and
performance evaluation of differentclustersbuilt atthe National Center
for High-Performance Computingin Taiwan. Performance of
processor, memory subsystem andinterconnect is a critical factor in the
overall performance of high performance computing platforms. The
evaluation compares different system architecture and software
platforms. Most supercomputer used HPL to benchmark their system
performance, in accordance with the requirement of the TOP500 List.
In this paper we consider system memory access factors that affect
benchmark performance, such as processor and memory
performance.We hope these works will provide useful information for
future development and construct cluster system.
Abstract: Electron multiplying charge coupled devices (EMCCDs) have revolutionized the world of low light imaging by introducing on-chip multiplication gain based on the impact ionization effect in the silicon. They combine the sub-electron readout noise with high frame rates. Signal-to-noise Ratio (SNR) is an important performance parameter for low-light-level imaging systems. This work investigates the SNR performance of an EMCCD operated in Non-inverted Mode (NIMO) and Inverted Mode (IMO). The theory of noise characteristics and operation modes is presented. The results show that the SNR of is determined by dark current and clock induced charge at high gain level. The optimum SNR performance is provided by an EMCCD operated in NIMO in short exposure and strong cooling applications. In contrast, an IMO EMCCD is preferable.
Abstract: To study the impact of the inter-module ventilation (IMV) on the space station, the Computational Fluid Dynamic (CFD) model under the influence of IMV, the mathematical model, boundary conditions and calculation method are established and determined to analyze the influence of IMV on cabin air flow characteristics and velocity distribution firstly; and then an integrated overall thermal mathematical model of the space station is used to consider the impact of IMV on thermal management. The results show that: the IMV has a significant influence on the cabin air flow, the flowrate of IMV within a certain range can effectively improve the air velocity distribution in cabin, if too much may lead to its deterioration; IMV can affect the heat deployment of the different modules in space station, thus affecting its thermal management, the use of IMV can effectively maintain the temperature levels of the different modules and help the space station to dissipate the waste heat.
Abstract: This study carried out in order to investigate the
effects of salinity on carbon isotope discrimination (Δ) of shoots and
roots of four sugar beet cultivars (cv) including Madison (British
origin) and three Iranian culivars (7233-P12, 7233-P21 and 7233-P29).
Plants were grown in sand culture medium in greenhouse conditions.
Plants irrigated with saline water (tap water as control, 50 mM, 150
mM, 250 mM and 350 mM of NaCl + CaCl2 in 5 to 1 molar ratio)
from 4 leaves stage for 16 weeks. Carbon isotope discrimination
significantly decreased with increasing salinity. Significant
differences of Δ between shoot and root were observed in all cvs and
all levels of salinity. Madison cv showed lower Δ in shoot and root
than other three cvs at all levels of salinity expect control, but cv
7233-P29 had significantly higher Δ values at saline conditions of 150
mM and above. Therefore, Δ might be applicable, as a useful tool, for
study of salinity tolerance of sugar beet genotypes.
Abstract: Morgan-s refinement calculus (MRC) is one of the
well-known methods allowing the formality presented in the program
specification to be continued all the way to code. On the other hand,
Object-Z (OZ) is an extension of Z adding support for classes and
objects. There are a number of methods for obtaining code from OZ
specifications that can be categorized into refinement and animation
methods. As far as we know, only one refinement method exists
which refines OZ specifications into code. However, this method
does not have fine-grained refinement rules and thus cannot be
automated. On the other hand, existing animation methods do not
present mapping rules formally and do not support the mapping of
several important constructs of OZ, such as all cases of operation
expressions and most of constructs in global paragraph. In this paper,
with the aim of providing an automatic path from OZ specifications
to code, we propose an approach to map OZ specifications into their
counterparts in MRC in order to use fine-grained refinement rules of
MRC. In this way, having counterparts of our specifications in MRC,
we can refine them into code automatically using MRC tools such as
RED. Other advantages of our work pertain to proposing mapping
rules formally, supporting the mapping of all important constructs of
Object-Z, and considering dynamic instantiation of objects while OZ
itself does not cover this facility.
Abstract: This paper presents an optimal design of poly-phase induction motor using Quadratic Interpolation based Particle Swarm Optimization (QI-PSO). The optimization algorithm considers the efficiency, starting torque and temperature rise as objective function (which are considered separately) and ten performance related items including harmonic current as constraints. The QI-PSO algorithm was implemented on a test motor and the results are compared with the Simulated Annealing (SA) technique, Standard Particle Swarm Optimization (SPSO), and normal design. Some benchmark problems are used for validating QI-PSO. From the test results QI-PSO gave better results and more suitable to motor-s design optimization. Cµ code is used for implementing entire algorithms.
Abstract: The optimal bisection width of r-dimensional N×
· · ·× N grid is known to be Nr-1 when N is even, but when
N is odd, only approximate values are available. This paper
shows that the exact bisection width of grid is Nr
-1
N-1 when N is odd.
Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: Automatic reading of handwritten cheque is a computationally
complex process and it plays an important role in financial
risk management. Machine vision and learning provide a viable
solution to this problem. Research effort has mostly been focused
on recognizing diverse pitches of cheques and demand drafts with an
identical outline. However most of these methods employ templatematching
to localize the pitches and such schemes could potentially
fail when applied to different types of outline maintained by the
bank. In this paper, the so-called outline problem is resolved by
a cheque information tree (CIT), which generalizes the localizing
method to extract active-region-of-entities. In addition, the weight
based density plot (WBDP) is performed to isolate text entities and
read complete pitches. Recognition is based on texture features using
neural classifiers. Legal amount is subsequently recognized by both
texture and perceptual features. A post-processing phase is invoked
to detect the incorrect readings by Type-2 grammar using the Turing
machine. The performance of the proposed system was evaluated
using cheque and demand drafts of 22 different banks. The test data
consists of a collection of 1540 leafs obtained from 10 different
account holders from each bank. Results show that this approach
can easily be deployed without significant design amendments.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The new status generated by technological advancements and changes in the global economy raises important issues on how communities and organisations need to innovate upon their traditional processes in order to adapt to the challenges of the Knowledge Society. The DialogoS+ European project aims to study the role of and promote social dialogue in the banking sector, strengthen the link between old and new members and make social dialogue at the European level a force for innovation and change, also given the context of the international crisis emerging in 2008- 2009. Under the scope of DialogoS+, this paper describes how the community of Europe-s banking sector trade unions attempted to adapt to the challenges of the Knowledge Society by exploiting the benefits of new channels of communication, learning, knowledge generation and diffusion focusing on the concept of roadmapping. Important dimensions of social dialogue such as collective bargaining and working conditions are addressed.
Abstract: A stage-structured predator-prey system with two time delays is considered. By analyzing the corresponding characteristic equation, the local stability of a positive equilibrium is investigated and the existence of Hopf bifurcations is established. Formulae are derived to determine the direction of bifurcations and the stability of bifurcating periodic solutions by using the normal form theory and center manifold theorem. Numerical simulations are carried out to illustrate the theoretical results. Based on the global Hopf bifurcation theorem for general functional differential equations, the global existence of periodic solutions is established.
Abstract: To solve the quick and accurate level-adjusting
problem in the process of spacecraft precise mating, automatic leveling
and equalizing hoist device for spacecraft is developed. Based on
lifting point adjustment by utilizing XY-workbench, the leveling and
equalizing controller by a self-adaptive control algorithm is proposed.
By simulation analysis and lifting test using engineering prototype,
validity and reliability of the hoist device is verified, which can meet
the precision mating requirements of practical applications for
spacecraft.
Abstract: The distressing flood scenarios that occur in
recent years at the surrounding areas of Sarawak River have
left damages of properties and indirectly caused disruptions of
productive activities. This study is meant to reconstruct a 100-year
flood event that took place in this river basin. Sarawak River Subbasin
was chosen and modeled using the one-dimensional
hydrodynamic modeling approach using InfoWorks River Simulation
(RS), in combination with Geographical Information System (GIS).
This produces the hydraulic response of the river and its floodplains
in extreme flooding conditions. With different parameters introduced
to the model, correlations of observed and simulated data are
between 79% – 87%. Using the best calibrated model, flood
mitigation structures are imposed along the sub-basin. Analysis is
done based on the model simulation results. Result shows that the
proposed retention ponds constructed along the sub-basin provide the
most efficient reduction of flood by 34.18%.
Abstract: The necessity of solving multi dimensional
complicated scientific problems beside the necessity of several
objective functions optimization are the most motive reason of born
of artificial intelligence and heuristic methods.
In this paper, we introduce a new method for multiobjective
optimization based on learning automata. In the proposed method,
search space divides into separate hyper-cubes and each cube is
considered as an action. After gathering of all objective functions
with separate weights, the cumulative function is considered as the
fitness function. By the application of all the cubes to the cumulative
function, we calculate the amount of amplification of each action and
the algorithm continues its way to find the best solutions. In this
Method, a lateral memory is used to gather the significant points of
each iteration of the algorithm. Finally, by considering the
domination factor, pareto front is estimated. Results of several
experiments show the effectiveness of this method in comparison
with genetic algorithm based method.
Abstract: In the present paper, we use generalized B-Spline curve in trigonometric form on circular domain, to capture the transcendental nature of circle involute curve and uncertainty characteristic of design. The required involute curve get generated within the given tolerance limit and is useful in gear design.
Abstract: In this paper we propose a new criterion for solving
the problem of channel shortening in multi-carrier systems. In a
discrete multitone receiver, a time-domain equalizer (TEQ) reduces
intersymbol interference (ISI) by shortening the effective duration of
the channel impulse response. Minimum mean square error (MMSE)
method for TEQ does not give satisfactory results. In [1] a new
criterion for partially equalizing severe ISI channels to reduce the
cyclic prefix overhead of the discrete multitone transceiver (DMT),
assuming a fixed transmission bandwidth, is introduced. Due to
specific constrained (unit morm constraint on the target impulse
response (TIR)) in their method, the freedom to choose optimum
vector (TIR) is reduced. Better results can be obtained by avoiding
the unit norm constraint on the target impulse response (TIR). In
this paper we change the cost function proposed in [1] to the cost
function of determining the maximum of a determinant subject to
linear matrix inequality (LMI) and quadratic constraint and solve the
resulting optimization problem. Usefulness of the proposed method
is shown with the help of simulations.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: In this paper, we propose a direct method based on the
real Schur factorization for solving the projected Sylvester equation
with relatively small size. The algebraic formula of the solution of
the projected continuous-time Sylvester equation is presented. The
computational cost of the direct method is estimated. Numerical
experiments show that this direct method has high accuracy.