Abstract: Analytical procedure was carried out in this paper to
calculate the ultimate load capacity of reinforced concrete corbels
strengthened or repaired externally with CFRP sheets. Strut and tie
method and shear friction method proposed earlier for analyzing
reinforced concrete corbels were modified to incorporate the effect of
external CFRP sheets bonded to the corbel. The points of weakness
of any method that lead to an inaccuracy, especially when
overestimating test results were checked and discussed. Comparison
of prediction with the test data indicates that the ratio of test /
calculated ultimate load is 0.82 and 1.17 using strut and tie method
and shear friction method, respectively. If the limits of maximum
shear stress is followed, the calculated ultimate load capacity using
shear friction method was found to underestimates test data
considerably.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.
Abstract: In this paper, a numerical solution based on nonpolynomial
cubic spline functions is used for finding the solution of
boundary value problems which arise from the problems of calculus
of variations. This approximation reduce the problems to an explicit
system of algebraic equations. Some numerical examples are also
given to illustrate the accuracy and applicability of the presented
method.
Abstract: This paper adopted the hybrid differential transform approach for studying heat transfer problems in a gold/chromium thin film with an ultra-short-pulsed laser beam projecting on the gold side. The physical system, formulated based on the hyperbolic two-step heat transfer model, covers three characteristics: (i) coupling effects between the electron/lattice systems, (ii) thermal wave propagation in metals, and (iii) radiation effects along the interface. The differential transform method is used to transfer the governing equations in the time domain into the spectrum equations, which is further discretized in the space domain by the finite difference method. The results, obtained through a recursive process, show that the electron temperature in the gold film can rise up to several thousand degrees before its electron/lattice systems reach equilibrium at only several hundred degrees. The electron and lattice temperatures in the chromium film are much lower than those in the gold film.
Abstract: There is no doubt that Internet technology is widely used by hotels and its demand is constantly booming. Hotels have largely adopted website information services through using different interactive tools, dimensions and attributes to achieve excellence in functionality and usability but these do not necessary equate with website effectiveness. One way to investigate the effectiveness of hotel website is from the perspective ofe-consumers. This exploratory research is to investigate the perceived importance of websites effectiveness of some selected independent small and medium-sized hotels (SMHs) located in Dubai, United Arab Emirates, from the perspective of Omanie-consumers by using non-random sampling method. From 400 questionnaire addressed to respondents in 27 organizations in Muscat the capital city of Oman, 173 are valid. Findings of this study assist SMHs management in Dubai with the reallocation of their resources and efforts in order to supportebusiness development and to sustain a competitive advantage.
Abstract: This research paper presents numerical studies of the
characteristics of warhead fragmentation in terms of initial velocities,
spray angles of fragments and fragment mass distribution of high
explosive (HE) warhead. The behavior of warhead fragmentation
depends on shape and size of warhead, thickness of casing, type of
explosive, number and position of detonator, and etc. This paper
focuses on the effects of material properties of warhead casing, i.e.
failure strain, initial yield and ultimate strength on the characteristics
of warhead fragmentation. It was found that initial yield and ultimate
strength of casing has minimal effects on the initial velocities and
spray angles of fragments. Moreover, a brittle warhead casing with
low failure strain tends to produce higher number of fragments with
less average fragment mass.
Abstract: Historic religious buildings located in seismic areas
have developed different failure mechanisms. Simulation of failure
modes is done with computer programs through a nonlinear dynamic
analysis or simplified using the method of failure blocks. Currently
there are simulation methodologies of failure modes based on the
failure rigid blocks method only for Roman Catholic churches type.
Due to differences of shape in plan, elevation and construction
systems between Orthodox churches and Catholic churches, for the
first time there were initiated researches in the development of this
simulation methodology for Orthodox churches. In this article are
presented the first results from the researches. The theoretical results
were compared with real failure modes recorded at an Orthodox
church from Banat region, severely damaged by earthquakes in
1991. Simulated seismic response, using a computer program based
on finite element method was confirmed by cracks after earthquakes.
The consolidation of the church was made according to these
theoretical results, realizing a rigid floor connecting all the failure
blocks.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: Introducing Electromagnetic Interference and Electromagnetic Compatibility, or “The Art of Black Magic", for engineering students might be a terrifying experience both for students and tutors. Removing the obstacle of large, expensive facilities like a fully fitted EMC laboratory and hours of complex theory, this paper demonstrates a design of a laboratory setup for student exercises, giving students experience in the basics of EMC/EMI problems that may challenge the functionality and stability of embedded system designs. This is done using a simple laboratory installation and basic measurement equipment such as a medium cost digital storage oscilloscope, at the cost of not knowing the exact magnitude of the noise components, but rather if the noise is significant or not, as well as the source of the noise. A group of students have performed a trial exercise with good results and feedback.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: Numerical investigation of the characteristics of an 80°
delta wing in combined force-pitch and free-roll is presented. The
implicit, upwind, flux-difference splitting, finite volume scheme and
the second-order-accurate finite difference scheme are employed to
solve the flow governing equations and Euler rigid-body dynamics
equations, respectively. The characteristics of the delta wing in
combined free-roll and large amplitude force-pitch is obtained
numerically and shows a well agreement with experimental data
qualitatively. The motion in combined force-pitch and free-roll
significantly reduces the lift force and transverse stabilities of the delta
wing, which is closely related to the flying safety. Investigations on
sensitive factors indicate that the roll-axis moment of inertia and the
structural damping have great influence on the frequency and
amplitude, respectively. Moreover, the turbulence model is considered
as an influencing factor in the investigation.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: It is known that symmetric encryption algorithms are
fast and easy to implement in hardware. Also elliptic curves have
proved to be a good choice for building encryption system. Although
most of the symmetric systems have been broken, we can create a
hybrid system that has the same properties of the symmetric
encryption systems and in the same time, it has the strength of
elliptic curves in encryption. As DES algorithm is considered the
core of all successive symmetric encryption systems, we modified
DES using elliptic curves and built a new DES algorithm that is hard
to be broken and will be the core for all other symmetric systems.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: This project focuses on the development of a line
follower algorithm for a Two Wheels Balancing Robot. In this
project, ATMEGA32 is chosen as the brain board controller to react
towards the data received from Balance Processor Chip on the
balance board to monitor the changes of the environment through
two infra-red distance sensor to solve the inclination angle problem.
Hence, the system will immediately restore to the set point (balance
position) through the implementation of internal PID algorithms at
the balance board. Application of infra-red light sensors with the PID
control is vital, in order to develop a smooth line follower robot. As a
result of combination between line follower program and internal self
balancing algorithms, we are able to develop a dynamically
stabilized balancing robot with line follower function.
Abstract: Recently, Thai education system is engaged in serious and promising reforms. One of the crucial elements in most of these educational reforms is the teacher professional development. Teachers today are under growing pressure to perform. However, most new teachers are not adequately prepared to meet the expectation. Consequently, this paper seeks to investigate the opinion of mentor teachers and university supervisors about professional development in the aspect of learning management skill of the preservice teachers in Rajabhat Universities, then compare the opinion between the mentor teachers and university supervisors about professional development in the aspect of learning management skill of the pre-service teachers. The study involved a cohort of 40 university supervisors and 77 mentor teachers. The research concludes by showing that mentor teachers viewed pre-service teacher as a professional teacher with an effective learning management skill. However, in the perspective of the university supervisor, pre-service teachers still have inadequate learning management skill.
Abstract: Microparticles carrier systems made from naturally occurring polymers based on chitosan/casein system appears to be a promising carrier for the sustained release of orally and parenteral administered drugs. In the current study we followed a microencapsulation technique based aqueous coacervation method to prepare chitosan/casein microparticles of compositions 1:1, 1:2 and 1:5 incorporated with chloramphenicol. Glutaraldehyde was used as a chemical cross-linking agent. The microparticles were prepared by aerosol method and studied by optical microscopy, infrared spectroscopy, thermo gravimetric analysis, swelling studies and drug release studies at various pH. The percentage swelling of the polymers are found to be in the order pH 4 > pH 10 > pH 7 and the increase in casein composition decrease the swelling percentage. The drug release studies also follow the above order.
Abstract: The desulfurization of coal using biological methods is an emerging technology. The biodesulfurization process uses the catalytic activity of chemolithotrophic acidpohiles in removing sulfur and pyrite from the coal. The present study was undertaken to examine the potential of Acidithiobacillus ferrooxidans in removing the pyritic sulfur and iron from high iron and sulfur containing US coal. The experiment was undertaken in 10 L batch stirred tank reactor having 10% pulp density of coal. The reactor was operated under mesophilic conditions and aerobic conditions were maintained by sparging the air into the reactor. After 35 days of experiment, about 64% of pyrite and 21% of pyritic sulfur was removed from the coal. The findings of the present study indicate that the biodesulfurization process does have potential in treating the high pyrite and sulfur containing coal. A good mass balance was also obtained with net loss of about 5% showing its feasibility for large scale application.