Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: This paper proposes a rotational invariant texture
feature based on the roughness property of the image for psoriasis
image analysis. In this work, we have applied this feature for image
classification and segmentation. The fuzzy concept is employed to
overcome the imprecision of roughness. Since the psoriasis lesion is
modeled by a rough surface, the feature is extended for calculating
the Psoriasis Area Severity Index value. For classification and
segmentation, the Nearest Neighbor algorithm is applied. We have
obtained promising results for identifying affected lesions by using
the roughness index and severity level estimation.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: Maize constitutes a major agrarian production for use
by the vast population but despite its economic importance; it has not
been produced to meet the economic needs of the country. Achieving
optimum yield in maize can meaningfully be supported by land
suitability analysis in order to guarantee self-sufficiency for future
production optimization. This study examines land suitability for
maize production through the analysis of the physicochemical
variations in soil properties and other land attributes over space using
a Geographic Information System (GIS) framework.
Physicochemical parameters of importance selected include slope,
landuse, physical and chemical properties of the soil, and climatic
variables. Landsat imagery was used to categorize the landuse,
Shuttle Radar Topographic Mapping (SRTM) generated the slope and
soil samples were analyzed for its physical and chemical components.
Suitability was categorized into highly, moderately and marginally
suitable based on Food and Agricultural Organisation (FAO)
classification, using the Analytical Hierarchy Process (AHP)
technique of GIS. This result can be used by small scale farmers for
efficient decision making in the allocation of land for maize
production.
Abstract: Established objective and subjective preconditions for
entrepreneurship, forming the business organically related whole, are
the necessary condition of successful entrepreneurial activities.
Objective preconditions for entrepreneurship are developed by
market economy that should stimulate entrepreneurship by allowing
the use of economic opportunities for all those who want to do
business in respective field while providing guarantees to all owners
and creating a stable business environment for entrepreneurs.
Subjective preconditions of entrepreneurship are formed primarily by
personal characteristics of the entrepreneur. These are his properties,
abilities, skills, physiological and psychological preconditions which
may be inherited, inborn or sequentially developed and obtained
during his life on the basis of education and influences of
surrounding environment. The paper is dealing with issues of
objective and subjective preconditions for entrepreneurship and
provides their analysis in view of the current situation in Slovakia. It
presents risks of the business environment in Slovakia that the Slovak
managers considered the most significant in 2014 and defines the
dominant attributes of the entrepreneur in the current business
environment in Slovakia.
Abstract: Analysis of the properties of coconut (Cocos nucifera)
and its oil was evaluated in this work using standard analytical
techniques. The analyses carried out include proximate composition
of the fruit, extraction of oil from the fruit using different process
parameters and physicochemical analysis of the extracted oil. The
results showed the percentage (%) moisture, crude lipid, crude
protein, ash and carbohydrate content of the coconut as 7.59, 55.15,
5.65, 7.35 and 19.51 respectively. The oil from the coconut fruit was
odourless and yellowish liquid at room temperature (30oC). The
treatment combinations used (leaching time, leaching temperature
and solute: solvent ratio) showed significant differences (P
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: Employers occupational safety and health training
obligations are regulated in 89/391/EEC Framework Directive and
also in 6331 numbered Occupational Health and Safety Law in
Turkey.
The main objective of this research is to determine and evaluate
the employers’ occupational health and safety training obligations in
Framework Directive in comparison with the 6331 numbered
Occupational Health and Safety Law and to examine training
principles in Turkey. For this purpose, employers’ occupational
health and safety training obligations examined in Framework
Directive and Occupational Health and Safety Law. This study
carried out through comparative scanning model and literature model.
The research data were collected through European Agency and
ministry legislations.
As a result, employers’ occupational health and safety training
obligations in the 6331 numbered Occupational Health and Safety
Law are compatible with the 89/391/EEC numbered Framework
Directive and training principles are determined by in different ways
like the trained workers, training issues, training period, training time
and trainers. In this study, employers’ training obligations are
evaluated in detail.
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: Wind energy offers a significant advantage such as no
fuel costs and no emissions from generation. However, wind energy
sources are variable and non-dispatchable. The utility grid is able to
accommodate the variability of wind in smaller proportion along with
the daily load. However, at high penetration levels, the variability can
severely impact the utility reserve requirements and the cost
associated with it. In this paper the impact of wind energy is
evaluated in detail in formulating the total utility cost. The objective
is to minimize the overall cost of generation while ensuring the
proper management of the load. Overall cost includes the curtailment
cost, reserve cost and the reliability cost, as well as any other penalty
imposed by the regulatory authority. Different levels of wind
penetrations are explored and the cost impacts are evaluated. As the
penetration level increases significantly, the reliability becomes a
critical question to be answered. Here we increase the penetration
from the wind yet keep the reliability factor within the acceptable
limit provided by NERC. This paper uses an economic dispatch (ED)
model to incorporate wind generation into the power grid. Power
system costs are analyzed at various wind penetration levels using
Linear Programming. The goal of this study is show how the
increases in wind generation will affect power system economics.
Abstract: The edges of low contrast images are not clearly
distinguishable to human eye. It is difficult to find the edges and
boundaries in it. The present work encompasses a new approach for
low contrast images. The Chebyshev polynomial based fractional
order filter has been used for filtering operation on an image. The
preprocessing has been performed by this filter on the input image.
Laplacian of Gaussian method has been applied on preprocessed
image for edge detection. The algorithm has been tested on two test
images.
Abstract: The English competence of Thai people was examined
in the context of knowledge of English in everyday life for Small and
Medium Entrepreneurs (SMEs), and also integrated with Second
language acquisition (SLA) students’ classroom. Second language
acquisition was applied to the results of the questionnaires and
interview forms. Levels of the need on English used for SME
entrepreneurs in Thailand, satisfaction on joining the street classroom
project were shown to be significantly high for some certain language
functions and satisfaction. Finding suggests that the language
functions on etiquette for professional use is essential and useful
because lesson learned can be used in the real situation for their
career. Implications for the climate of the street classroom are
discussed.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.
Abstract: It has become an increasing evident that large
development influences the climate. There are concerns that rising
temperature over developed areas could have negative impact and
increase living discomfort within city boundaries. Temperature trends
in Ibadan city have received little attention, yet the area has
experienced heavy urban expansion between 1972 and 2014. This
research aims at examining the impact of landuse change on surface
temperature knowing that the built-up environment absorb and store
solar energy, resulting into the Urban Heat Island (UHI) effect. The
Landsat imagery was used to examine the landuse change for a
period of 42 years (1972-2014). Land Surface Temperature (LST)
was obtained by converting the thermal band to a surface temperature
map and zonal statistic analyses was used to examine the relationship
between landuse and temperature emission. The results showed that
the settlement area increased to a large extent while the area covered
by vegetation reduced during the study period. The spatial and
temporal trends of surface temperature are related to the gradual
change in urban landuse/landcover and the settlement area has the
highest emission. This research provides useful insight into the
temporal behavior of the Ibadan city.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: Concrete is found to undergo degradation when
subjected to elevated temperatures and loose substantial amount of its
strength. The loss of strength in concrete is mainly attributed to
decomposition of C-S-H and release of physically and chemically
bound water, which begins when the exposure temperature exceeds
100°C. When such a concrete comes in contact with moisture, the
cement paste is found rehydrate and considerable amount of strength
lost is found to recover. This paper presents results of an
experimental program carried out to investigate the effect of recuring
on strength gain of OPC concrete specimens subjected to elevated
temperatures from 200°C to 800°C, which were subjected to
retention time of two hours and four hours at the designated
temperature. Strength recoveries for concrete subjected to 7
designated elevated temperatures are compared. It is found that the
efficacy of recuring as a measure of strength recovery reduces with
increase in exposure temperature.
Abstract: The object of the present paper is to investigate several
general families of bilinear and bilateral generating functions with
different argument for the Gauss’ hypergeometric polynomials.
Abstract: Human leukocyte antigen (HLA) typing from next
generation sequencing (NGS) data has the potential for applications in
clinical laboratories and population genetic studies. Here we introduce
a novel technique for HLA typing from NGS data based on
read-mapping using a comprehensive reference panel containing all
known HLA alleles and de novo assembly of the gene-specific short
reads. An accurate HLA typing at high-digit resolution was achieved
when it was tested on publicly available NGS data, outperforming
other newly-developed tools such as HLAminer and PHLAT.