Abstract: The detection of the polymer melt state during
manufacture process is regarded as an efficient way to control the
molded part quality in advance. Online monitoring rheological
property of polymer melt during processing procedure provides an
approach to understand the melt state immediately. Rheological
property reflects the polymer melt state at different processing
parameters and is very important in injection molding process
especially. An approach that demonstrates how to calculate
rheological property of polymer melt through in-process
measurement, using injection molding as an example, is proposed in
this study. The system consists of two sensors and a data acquisition
module can process the measured data, which are used for the
calculation of rheological properties of polymer melt. The rheological
properties of polymer melt discussed in this study include shear rate
and viscosity which are investigated with respect to injection speed
and melt temperature. The results show that the effect of injection
speed on the rheological properties is apparent, especially for high
melt temperature and should be considered for precision molding
process.
Abstract: Micro-alloyed steel components are used in
automotive industry for the necessity to make the manufacturing
process cycles shorter when compared to conventional steel by
eliminating heat treatment cycles, so an important saving of costs and
energy can be reached by reducing the number of operations. Microalloying
elements like vanadium, niobium or titanium have been
added to medium carbon steels to achieve grain refinement with or
without precipitation strengthening along with uniform
microstructure throughout the matrix. Present study reports the
applicability of medium carbon vanadium micro-alloyed steel in hot
forging. Forgeability has been determined with respect to different
cooling rates, after forging in a hydraulic press at 50% diameter
reduction in temperature range of 900-11000C. Final microstructures,
hardness, tensile strength, and impact strength have been evaluated.
The friction coefficients of different lubricating conditions, viz.,
graphite in hydraulic oil, graphite in furnace oil, DF 150 (Graphite,
Water-Based) die lubricant and dry or without any lubrication were
obtained from the ring compression test for the above micro-alloyed
steel. Results of ring compression tests indicate that graphite in
hydraulic oil lubricant is preferred for free forging and dry lubricant
is preferred for die forging operation. Exceptionally good forgeability
and high resistance to fracture, especially for faster cooling rate has
been observed for fine equiaxed ferrite-pearlite grains, some amount
of bainite and fine precipitates of vanadium carbides and
carbonitrides. The results indicated that the cooling rate has a
remarkable effect on the microstructure and mechanical properties at
room temperature.
Abstract: The aim of this study was to build ‘Ubi-Net’, a
decision-making support system for systematic establishment in
U-City planning. We have experienced various urban problems caused
by high-density development and population concentrations in
established urban areas. To address these problems, a U-Service
contributes to the alleviation of urban problems by providing real-time
information to citizens through network connections and related
information. However, technology, devices, and information for
consumers are required for systematic U-Service planning in towns
and cities where there are many difficulties in this regard, and a lack of
reference systems.
Thus, this study suggests methods to support the establishment of
sustainable planning by providing comprehensive information
including IT technology, devices, news, and social networking
services (SNS) to U-City planners through intelligent searches. In this
study, we targeted Smart U-Parking Planning to solve parking
problems in an ‘old’ city. Through this study, we sought to contribute
to supporting advances in U-Space and the alleviation of urban
problems.
Abstract: The concept of technology as well as itself has
evolved continuously over time, such that, nowadays, this concept is
still marked by myths and realities. Even the concept of science is
frequently misunderstood as technology. In this way, this paper
presents different forms of interpretation of the concept of technology
in the course of history, as well as the social and cultural aspects
associated with it, through an analysis made by means of insights
from sociological studies of science and technology and its multiple
relations with society. Through the analysis of contents, the paper
presents a classification of how technology is interpreted in the social
sphere and search channel efforts to show how a broader
understanding can contribute to better interpretations of how
scientific and technological development influences the environment
in which we operate. The text also presents a particular point of view
for the interpretation of the concept from the analysis throughout the
whole work.
Abstract: The ultrasound imaging is very popular to diagnosis
the disease because of its non-invasive nature. The ultrasound
imaging slowly produces low quality images due to the presence of
spackle noise and wave interferences. There are several algorithms to
be proposed for the segmentation of ultrasound carotid artery images
but it requires a certain limit of user interaction. The pixel in an
image is highly correlated so the spatial information of surrounding
pixels may be considered in the process of image segmentation which
improves the results further. When data is highly correlated, one pixel
may belong to more than one cluster with different degree of
membership. There is an important step to computerize the evaluation
of arterial disease severity using segmentation of carotid artery lumen
in 2D and 3D ultrasonography and in finding vulnerable
atherosclerotic plaques susceptible to rupture which can cause stroke.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: Doxorubicin, also known as Adriamycin, is an
anthracycline class of drug used in cancer chemotherapy. It is used in
the treatment of non-Hodgkin’s lymphoma, multiple myeloma, acute
leukemia, breast cancer, lung cancer, endometrium cancer and ovary
cancers. It functions via intercalating DNA and ultimately killing
cancer cells. The major side effects of doxorubicin are hair loss,
myelosuppression, nausea & vomiting, oesophagitis, diarrhea, heart
damage and liver dysfunction. The minor modifications in the
structure of compound exhibit large variation in the biological
activity, has prompted us to carry out the synthesis of sulfonamide
derivatives. Sulfonamide is an important feature with broad spectrum
of biological activity such as antiviral, antifungal, diuretics, antiinflammatory,
antibacterial and anticancer activities. Structure of the
synthesized compound N-(1-methyl-2-oxo-2-N-methyl anilinoethyl)
benzene sulfonamide confirmed by proton nuclear magnetic
resonance (1H NMR),13C NMR, Mass and FTIR spectroscopic tools
to assure the position of all protons and hence stereochemistry of the
molecule. Further we have reported the binding potential of
synthesized sulfonamide analogues in comparison to doxorubicin
drug using Auto Dock 4.2 software. Computational binding energy
(B.E.) and inhibitory constant (Ki) has been evaluated for the
synthesized compound in comparison of doxorubicin against Poly
(dA-dT).Poly (dA-dT) and Poly (dG-dC).Poly (dG-dC) sequences.
The in vitro cytotoxic study against human breast cancer cell lines
confirms the better anticancer activity of the synthesized compound
over currently in use anticancer drug doxorubicin. The IC50 value of
the synthesized compound is 7.12 μM whereas for doxorubicin is 7.2
μM.
Abstract: Formal verification is proposed to ensure the
correctness of the design and make functional verification more
efficient. As cache plays a vital role in the design of System on Chip
(SoC), and cache with Memory Management Unit (MMU) and cache
memory unit makes the state space too large for simulation to verify,
then a formal verification is presented for such system design. In the
paper, a formal model checking verification flow is suggested and a
new cache memory model which is called “exhaustive search model”
is proposed. Instead of using large size ram to denote the whole cache
memory, exhaustive search model employs just two cache blocks. For
cache system contains data cache (Dcache) and instruction cache
(Icache), Dcache memory model and Icache memory model are
established separately using the same mechanism. At last, the novel
model is employed to the verification of a cache which is module of a
custom-built SoC system that has been applied in practical, and the
result shows that the cache system is verified correctly using the
exhaustive search model, and it makes the verification much more
manageable and flexible.
Abstract: The aim of research was to define the relations
between volatile compounds, some parameters (pH, titratable acidity
(TA), total soluble solid (TSS), lactic acid bacteria count) and
consumer preference of commercial fermented milks. These relations
tend to be used for controlling and developing new fermented milk
product. Three leading commercial brands of fermented milks in
Thailand were evaluated by consumers (n=71) using hedonic scale
for four attributes (sweetness, sourness, flavour, and overall liking),
volatile compounds using headspace-solid phase microextraction
(HS-SPME) GC-MS, pH, TA, TSS and LAB count. Then the
relations were analyzed by principal component analysis (PCA). The
PCA data showed that all of four attributes liking scores were related
to each other. They were also related to TA, TSS and volatile
compounds. The related volatile compounds were mainly on
fermented produced compounds including acetic acid, furanmethanol,
furfural, octanoic acid and the volatiles known as artificial fruit
flavour (beta pinene, limonene, vanillin, and ethyl vanillin). These
compounds were provided the information about flavour addition in
commercial fermented milk in Thailand.
Abstract: Operations, maintenance and reliability of wind
turbines have received much attention over the years due to the rapid
expansion of wind farms. This paper explores early fault diagnosis
technique for a 5MW wind turbine system subjected to multiple
faults, where genetic optimization algorithm is employed to make the
residual sensitive to the faults, but robust against disturbances. The
proposed technique has a potential to reduce the downtime mostly
caused by the breakdown of components and exploit the productivity
consistency by providing timely fault alarms. Simulation results show
the effectiveness of the robust fault detection methods used under
Matlab/Simulink/Gatool environment.
Abstract: This paper proposes a mathematical model and
examines the performance of an exact algorithm for a location–
transportation problems in humanitarian relief. The model determines
the number and location of distribution centers in a relief network,
the amount of relief supplies to be stocked at each distribution center
and the vehicles to take the supplies to meet the needs of disaster
victims under capacity restriction, transportation and budgetary
constraints. The computational experiments are conducted on the
various sizes of problems that are generated. Branch and bound
algorithm is applied for these problems. The results show that this
algorithm can solve problem sizes of up to three candidate locations
with five demand points and one candidate location with up to twenty
demand points without premature termination.
Abstract: This research aimed to study about motivation for
students of Suan Sunandha Rajabhat University to follow and happily
live according to Sufficiency Economy Philosophy. Having collected
394 questionnaires, the result showed that most students had great
motivation to follow this philosophy at a high level, especially in
terms of righteousness in profession; besides, students’ determination
and intention to apply this philosophy in everyday lives was
impressive though the students’ families were not completely ready.
Each of students, in fact, consulted their families for plans of any
activities without tiredness and discouragement based on the saying,
“Where there’s a will, there’s a way.” On the part of universities life,
students interacted with society and created projects that supported
income to the community including exercises, sports, recreational
activities, and community services.
Abstract: The work studied the effect of germination on
proximate, phenol and flavonoid content and antioxidant activities
(AOA) of African Yam been (AYB). Germination was done in
controlled dark chamber (100% RH, 28oC). The proximate, phenol
and flavonoid content and antioxidant activities before and after
germination were investigated. The crude protein, moisture, and
crude fiber content of germinated AYB were significantly higher
(P
Abstract: It is likely that robots will cross the boundaries of
industry into households over the next decades. With demographic
challenges worldwide, the future ageing populations will require the
introduction of assistive technologies capable of providing, care,
human dignity and quality of life through the aging process. Robotics
technology has a high potential for being used in the areas of social
and healthcare by promoting a wide range of activities such as
entertainment, companionship, supervision or cognitive and physical
assistance. However such close Human Robotics Interaction (HRI)
encompass a rich set of ethical scenarios that need to be addressed
before Socially Assistive Robots (SARs) reach the global markets.
Such interactions with robots may seem a worthy goal for many
technical/financial reasons but inevitably require close attention to
the ethical dimensions of such interactions. This article investigates
the current HRI benchmark of social success. It revises it according
to the ethical principles of beneficence, non-maleficence and justice
aligned with social care ethos. An extension of such benchmark is
proposed based on an empirical study of HRIs conducted with elderly
groups.
Abstract: In urban area, several landmarks may affect housing
price and rents, and hedonic analysis should employ distance variables
corresponding to each landmarks. Unfortunately, the effects of
distances to landmarks on housing prices are generally not consistent
with the true price. These distance variables may cause magnitude
error in regression, pointing a problem of spatial multicollinearity. In
this paper, we provided some approaches for getting the samples with
less bias and method on locating the specific sampling area to avoid
the multicollinerity problem in two specific landmarks case.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Precise capture of plantar 3D surface of the foot at the
loading gait phases on rigid substrates was found to be valuable for
the assessment of the physiology, health and problems of the feet.
Photogrammetry, a precision 3D spatial data capture technique is
suitable for this type of dynamic application. In this research, the
technique is utilised to study the plantar deformation as a result of
having a strip of kinesiology tape on the plantar surface during the
loading phase of gait. For this pilot study, one healthy adult male
subject was recruited under the University’s human research ethics
guidelines for this preliminary study. The 3D plantar deformation
data with and without applying the tape were analysed. The results
and analyses are presented together with detailed findings.
Abstract: ESPRIT-TLS method appears a good choice for high
resolution fault detection in induction machines. It has a very high
effectiveness in the frequency and amplitude identification.
Contrariwise, it presents a high computation complexity which
affects its implementation in real time fault diagnosis. To avoid this
problem, a Fast-ESPRIT algorithm that combined the IIR band-pass
filtering technique, the decimation technique and the original
ESPRIT-TLS method was employed to enhance extracting accurately
frequencies and their magnitudes from the wind stator current with
less computation cost. The proposed algorithm has been applied to
verify the wind turbine machine need in the implementation of an online,
fast, and proactive condition monitoring. This type of remote
and periodic maintenance provides an acceptable machine lifetime,
minimize its downtimes and maximize its productivity. The
developed technique has evaluated by computer simulations under
many fault scenarios. Study results prove the performance of Fast-
ESPRIT offering rapid and high resolution harmonics recognizing
with minimum computation time and less memory cost.
Abstract: In this study, an experiment was executed related to
the strength of wooden materials which have been commonly used
both in the past and present against pressure and whether fire
retardant materials used against fire have any effects or not. Totally
81 samples which included 3 different wood species, 3 different
sizes, 2 different fire retardants and 2 unprocessed samples were
prepared. Compressive pressure tests were applied to the prepared
samples, their variance analyses were executed in accordance with
the obtained results and it was aimed to determine the most
convenient wooden materials and fire-retardant coating material. It
was also determined that the species of wood and the species of
coating caused the decrease and/or increase in the resistance against
pressure.
Abstract: Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.