Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: Since the marine environmental conditions are
extremely different from the other ones, marine actinomycetes might
produce novel bioactive compounds. Therefore, actinomycete strains
were screened from marine water and sediment samples collected
from the coastal areas of Northern Vietnam. Ninety-nine
actinomycete strains were obtained on starch-casein agar media by
dilution technique, only seven strains, named HP112, HP12, HP411,
HPN11, HP 11, HPT13 and HPX12, showed significant antibacterial
activity against both gram-positive and gram-negative bacteria
(Bacillus subtilis ATCC 6633, Staphylococcus epidemidis ATCC
12228, Escherichia coli ATCC 11105). Further studies were carried
out with the most active HP411 strain against Candida albicans
ATCC 10231. This strain could grow rapidly on starch casein agar
and other media with high salt containing 7-10% NaCl at 28-30oC.
Spore-chain of HP411 showed an elongated and circular shape with
10 to 30 spores/chain. Identification of the strain was carried out by
employing the taxonomical studies including the 16S rRNA
sequence. Based on phylogenetic and phenotypic evidence it is
proposed that HP411 to be belongs to species Streptomyces
variabilis. The potent of the crude extract of fermentation broth of
HP411 that are effective against wide range of pathogens: both grampositive,
gram-negative and fungi. Further studies revealed that the
crude extract HP411 could obtain the anticancer activity for cancer
cell lines: Hep-G2 (liver cancer cell line); RD (cardiac and skeletal
muscle letters cell line); FL (membrane of the uterus cancer cell line).
However, the actinomycetes from marine ecosystem will be useful
for the discovery of new drugs in the future.
Abstract: The bean (Phaseolus vulgaris L.) is one of the best
known of the legumes, and it has a long cultivation tradition in Italy.
The territory of “Subappennino Dauno” (southern Italy) is at around
700 m a.s.l. and is predominantly grown with cereals, olive trees and
grapevines. Ecotypes of white beans to eat dry (such as cannellini
beans) are also grown, which are sought for their palatability, high
digestibility, and ease of cooking. However, these are not easy to find
on the market due to their low production in relatively small areas
and on small family farms that use seeds handed down from
generation to generation. The introduction of these ecotypes in plain
areas of the Puglia region would provide an opportunity to promote
the diffusion of this type of bean. To investigate the adaptability of
these ecotypes in plain environments (Cerignola, in southern Italy) a
comparative trial was carried out between three ‘Monti Dauni’
ecotypes (E1, E2, E3) that are native to mountain areas and the
similar commercial variety, ‘Cannellini’. The data provide useful
information about the quantitative and qualitative characteristics of
these ecotypes when grown in lowland environments. Ecotype E3
provided the greatest bean production (2.34 t ha-1) compared to
‘Cannellini’ (1.28 t ha-1) and the other ecotypes (0.55 and 0.40 t ha-1,
for E1 and E2, respectively), due to its greater plant growth and the
larger size of the seed (and thickness, in particular). Finally, ecotype
E2 provided the greatest protein content (31.2%), although not
significantly different from the commercial cultivar ‘Cannellini’
(32.1%).
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: The main goal of this paper was evaluate the effect of
diets containing different levels of probiotic on performance and milk
composition of lactating cows.
Eight Holstein cows were distributed in two 4x4 Latin square. The
diets were based on corn silage, concentrate and the treatment (0, 3, 6
or 9 grams of probiotic/animal/day). It was evaluated the dry matter
intake of nutrients, milk yield and composition.
The use of probiotics did not affect the nutrient intake (p>0.05)
neither the daily milk production or corrected to 4% fat (p>0.05).
However, it was observed that there was a significant fall in milk
composition with higher levels of probiotics supplementation.
These results emphasize the need of further studies with different
experimental designs or improve the number of Latin square with
longer periods of adaptation.
Abstract: Folic acid (FA) is known to be an important
supplement to prevent neural tube defect (NTD) in pregnant women.
Similar to some commercial formulations, sodium bicarbonate
solution is used as a solvent for FA. This work uses the antisolvent
vapour precipitation (AVP), incorporating ethanol vapour as the
convective drying medium in place of air to produce branch-like
micro-structure FA particles. Interestingly, the dissolution rate of the
resultant particle is 2-3 times better than the particle produce from
conventional air drying due to the higher surface area of particles
produced. The higher dissolution rate could possibly improve the
delivery and absorption of FA in human body. This application could
potentially be extended to other commercial products, particularly in
less soluble drugs to improve its solubility.
Abstract: The purpose of the present work is to review some
data for the management challenges that the aquaculture industry in
Greece is currently facing. The results indicate that Greek
aquaculture fish farms apply Human Resources Management (HRM)
practices which can increase motivation, commitment and job
satisfaction of their personnel. In turn, these practices can increase
the productivity of the business. The Greek fish farms appear to
invest in research and technological innovation with a good record in
research activities and the generation of patents. Interestingly, the
results of the present work were carried out during the period of the
recent economic crisis in Greece. Several sectors of the Greek
economy were severely affected by the financial problems of the
Greek government and the Greek banks. Under the adverse
economical conditions created by the Greek economic crisis, even the
Greek aquaculture industry, which historically is considered as a
thriving national exporting business sector, experienced harsh
economic and market conditions. As a result of the global, European
and national economic crisis, consumption of fish dropped while
companies had to hold most of their stocked fish in order to regulated
the flow to the market and the price. This occurred at a time where
Banks in Greece had their own financial crisis – banking crisis -
which resulted in limited access to lending for the all business sectors
of the national economy including the Greek aquaculture industry. In
spite of these economic conditions, the Greek aquaculture industry,
after a series of mergers and acquisitions, has now stabilized
production and exhibits very good prospects for future growth.
Evidently, the firms had to cut salaries and on some occasions even
pay their staff in arrears. Nevertheless, the results presented in this
paper indicate that during the economic crisis, the surveyed fish
farms maintained their HRM practices, investing in their human
capital and technological input. In fact, human capital and
technological input are the ticket for future success of companies in
any business sector.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: Heavy metals are one of the major groups of
contaminants in the environment and many of them are toxic even at
very low concentration in plants and animals. However, some metals
play important roles in the biological function of many enzymes in
living organisms. Metals such as zinc, iron, and cooper are important
for survival and activity of enzymes in plants, however heavy metals
can inhibit enzyme which is responsible for defense system of plants.
Polyphenol oxidase (PPO) is a copper-containing metalloenzyme
which is responsible for enzymatic browning reaction of plants.
Enzymatic browning is a major problem for the handling of
vegetables and fruits in food industry. It can be increased and
effected with many different futures such as metals in the nature and
ground. In the present work, PPO was isolated and characterized
from green leaves of red poppy plant (Papaverr hoeas). Then, the
effect of some known antibrowning agents which can form
complexes with metals and metals were investigated on the red poppy
PPO activity. The results showed that glutathione was the most
potent inhibitory effect on PPO activity. Cu(II) and Fe(II) metals
increased the enzyme activities however, Sn(II) had the maximum
inhibitory effect and Zn(II) and Pb(II) had no significant effect on the
enzyme activity. In order to reduce the effect of heavy metals, the
effects of metal-antibrowning agent complexes on the PPO activity
were determined. EDTA and metal complexes had no significant
effect on the enzyme. L-ascorbic acid and metal complexes decreased
but L-ascorbic acid-Cu(II)-complex had no effect. Glutathione–metal
complexes had the best inhibitory effect on Red poppy leaf PPO
activity.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: Load carrying capacity of an oil lubricated two-axial
groove journal bearing is simulated by taking into account the
viscosity variations in lubricant due to the addition of TiO2
nanoparticles as lubricant additive. Shear viscosities of TiO2
nanoparticle dispersions in oil are measured for various nanoparticle
additive concentrations. The viscosity model derived from the
experimental viscosities is employed in a modified Reynolds
equation to obtain the pressure profiles and load carrying capacity of
two-axial groove journal bearing. Results reveal an increase in load
carrying capacity of bearings operating on nanoparticle dispersions as
compared to plain oil.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: The study area is Zaria, located in the basement
complex of northern Nigeria. The rock type forming the major part of
the Zaria batholith is granite. This research work was carried out to
compare the responses of seismic refraction tomography and
resistivity tomography in the same geologic environment and under
the same conditions. Hence, the choice of the site that has a visible
granitic outcrop that extends across a narrow stream channel and is
flanked by unconsolidated overburden, a neutral profile that was
covered by plain overburden and a site with thick lateritic cover
became necessary. The results of the seismic and resistivity
tomography models reveals that seismic velocity and resistivity does
not always simultaneously increase with depth, but their responses in
any geologic environment are determined by changes in the
mechanical and chemical content of the rock types rather than depth.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: This research paper aims to identify, analyze and rank
factors affecting labor productivity in Spain with respect to their
relative importance. Using a selected set of 35 factors, a structured
questionnaire survey was utilized as the method to collect data from
companies. Target population is comprised by a random
representative sample of practitioners related with the Spanish
construction industry. Findings reveal the top five ranked factors are
as follows: (1) shortage or late supply of materials; (2) clarity of the
drawings and project documents; (3) clear and daily task assignment;
(4) tools or equipment shortages; (5) level of skill and experience of
laborers. Additionally, this research also pretends to provide simple
and comprehensive recommendations so that they could be
implemented by construction managers for an effective management
of construction labor forces.
Abstract: The most important part of modern lean low NOx combustors is a premixer where swirlers are often used for intensification of mixing processes and further formation of required flow pattern in combustor liner. Swirling flow leads to formation of complex eddy structures causing flow perturbations. It is able to cause combustion instability. Therefore, at design phase, it is necessary to pay great attention to aerodynamics of premixers. Analysis based on unsteady CFD modeling of swirling flow in production combustor swirler showed presence of large number of different eddy structures that can be conditionally divided into three types relative to its location of origin and a propagation path. Further, features of each eddy type were subsequently defined. Comparison of calculated and experimental pressure fluctuations spectrums verified correctness of computations.