Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: Advanced head and neck cancers are aggressive
tumours, which require aggressive treatment. Treatment efficiency is
often hindered by cancer cell repopulation during radiotherapy,
which is due to various mechanisms triggered by the loss of tumour
cells and involves both stem and differentiated cells. The aim of the
current paper is to present in silico simulations of radiotherapy
schedules on a virtual head and neck tumour grown with biologically
realistic kinetic parameters. Using the linear quadratic formalism of
cell survival after radiotherapy, altered fractionation schedules
employing various treatment breaks for normal tissue recovery are
simulated and repopulation mechanism implemented in order to
evaluate the impact of various cancer cell contribution on tumour
behaviour during irradiation. The model has shown that the timing of
treatment breaks is an important factor influencing tumour control in
rapidly proliferating tissues such as squamous cell carcinomas of the
head and neck. Furthermore, not only stem cells but also
differentiated cells, via the mechanism of abortive division, can
contribute to malignant cell repopulation during treatment.
Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: Member States shall establish zones and
agglomerations throughout their territory to assess and manage air
quality in order to comply with European directives.
In Italy decree 155/2010, transposing Directive 2008/50/EC on
ambient air quality and cleaner air for Europe, merged into a single
act the previous provisions on ambient air quality assessment and
management, including those resulting from the implementation of
Directive 2004/107/EC relating to arsenic, cadmium, nickel, mercury
and polycyclic aromatic hydrocarbons in ambient air.
Decree 155/2010 introduced stricter rules for identifying zones on
the basis of the characteristics of the territory in spite of considering
pollution levels, as it was in the past. The implementation of such
new criteria has reduced the great variability of the previous zoning,
leading to a significant reduction of the total number of zones and to
a complete and uniform ambient air quality assessment and
management throughout the Country.
The present document is related to the new zones definition in
Italy according to Decree 155/2010. In particular the paper contains
the description and the analysis of the outcome of zoning and
classification.
Abstract: Fructo-oligosaccharides (FOS) are produced from
sucrose by Aureobasidium pullulans in yields between 40-60%
(w/w). To increase the amount of FOS it is necessary to remove the
small, non-prebiotic sugars, present. Two methods for producing
high-purity FOS have been developed: the use of microorganisms
able to consume small saccharides; and the use of continuous
chromatography to separate sugars: simulated moving bed (SMB). It
is herein proposed the combination of both methods. The aim of this
study is to optimize the composition of the fermentative broth (in
terms of salts and sugars) that will be further purified by SMB. A
yield of 0.63 gFOS.gSucrose^-1 was obtained with A. pullulans using low
amounts of salts in the initial fermentative broth. By removing the
small sugars, Saccharomyces cerevisiae and Zymomonas mobilis
increased the percentage of FOS from around 56.0% to 83% (w/w) in
average, losing only 10% (w/w) of FOS during the recovery process.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: Although it is not intended to identify distance
education students as a homogeneous group, recent research has
demonstrated that there are some demographic and personality
common traits among most of them that provide the basis for the
description of a typical distance learning student. The purpose of this
paper is to describe these common traits and to facilitate their
learning journey within a distance education program. The described
research is an initiative of the Distance Education Unit at the
European University Cyprus (Laureate International Universities) in
the context of its action for the improvement of the students’
performance.
Abstract: In view of a possible application in optical data
storage devices, diffraction grating efficiency of an organic dye, Acid
Fuchsin doped in PMMA matrix was studied under excitation with
CW diode pumped Nd: YAG laser at 532 nm. The open aperture Zscan
of dye doped polymer displayed saturable absorption and the
closed aperture Z-scan of the samples exhibited negative
nonlinearity. The diffraction efficiency of the grating is the ratio of
the intensity of the first order diffracted power to the incident read
beam power. The dye doped polymer films were found to be good
media for recording. It is observed that the formation of gratings
strongly depend on the concentration of dye in the polymer film, the
intensity ratios of the writing beams and the angle between the
writing beams. It has been found that efficient writing can be made at
an angle of 20o and when the intensity ratio of the writing beams is
unity.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: To develop AZ91D magnesium alloys with improved
properties, we have applied TiN and VN/TiN multilayer coatings
using DC magnetron sputter technique. Coating structure, surface
morphology, chemical bonding and corrosion resistance of coatings
were analyzed by x-ray diffraction (XRD), scanning electron
microscope (SEM), x-ray photoelectron spectroscopy (XPS), and
tafel extrapolation method, respectively. XPS analysis reveal that VN
overlayer reacts with oxygen at the VN/TiN interface and forms more
stable TiN layer. Morphological investigations and the corrosion
results show that VN/TiN multilayer thin film coatings are quite
effective to optimize the corrosion resistance of Mg alloys.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.
Abstract: In the UK, flooding is responsible for significant
losses to the economy due to the impact on businesses, the vast
majority of which are Small and Medium Enterprises (SMEs).
Businesses of this nature tend to lack formal plans to aid their
response to and recovery from disruptive events such as flooding.
This paper reports on work on how an agent-based model (ABM) is
being developed based on interview data gathered from SMEs at-risk
of flooding and/or have direct experience of flooding. The ABM will
enable simulations to be performed allowing investigations of
different response strategies which SMEs may employ to lessen the
impact of flooding, thus strengthening their resilience.
Abstract: A key issue in seismic risk analysis within the context
of Performance-Based Earthquake Engineering is the evaluation of
the expected seismic damage of structures under a specific
earthquake ground motion. The assessment of the seismic
performance strongly depends on the choice of the seismic Intensity
Measure (IM), which quantifies the characteristics of a ground
motion that are important to the nonlinear structural response. Several
conventional IMs of ground motion have been used to estimate their
damage potential to structures. Yet, none of them has been proved to
be able to predict adequately the seismic damage. Therefore,
alternative, scalar intensity measures, which take into account not
only ground motion characteristics but also structural information
have been proposed. Some of these IMs are based on integration of
spectral values over a range of periods, in an attempt to account for
the information that the shape of the acceleration, velocity or
displacement spectrum provides. The adequacy of a number of these
IMs in predicting the structural damage of 3D R/C buildings is
investigated in the present paper. The investigated IMs, some of
which are structure specific and some are non structure-specific, are
defined via integration of spectral values. To achieve this purpose
three symmetric in plan R/C buildings are studied. The buildings are
subjected to 59 bidirectional earthquake ground motions. The two
horizontal accelerograms of each ground motion are applied along
the structural axes. The response is determined by nonlinear time
history analysis. The structural damage is expressed in terms of the
maximum interstory drift as well as the overall structural damage
index. The values of the aforementioned seismic damage measures
are correlated with seven scalar ground motion IMs. The comparative
assessment of the results revealed that the structure-specific IMs
present higher correlation with the seismic damage of the three
buildings. However, the adequacy of the IMs for estimation of the
structural damage depends on the response parameter adopted.
Furthermore, it was confirmed that the widely used spectral
acceleration at the fundamental period of the structure is a good
indicator of the expected earthquake damage level.
Abstract: Artificial Immune Systems (AIS), inspired by the
human immune system, are algorithms and mechanisms which are
self-adaptive and self-learning classifiers capable of recognizing and
classifying by learning, long-term memory and association. Unlike
other human system inspired techniques like genetic algorithms and
neural networks, AIS includes a range of algorithms modeling on
different immune mechanism of the body. In this paper, a mechanism
of a human immune system based on apoptosis is adopted to build an
Intrusion Detection System (IDS) to protect computer networks.
Features are selected from network traffic using Fisher Score. Based
on the selected features, the record/connection is classified as either
an attack or normal traffic by the proposed methodology. Simulation
results demonstrates that the proposed AIS based on apoptosis
performs better than existing AIS for intrusion detection.
Abstract: In this paper, the influence of upstream structures on the flow patternaround and inside the wind-catcher is experimentally investigated by smoke flow visualization techniques. Wind-catchers are an important part of natural ventilation in residential buildings or public places such as shopping centers, libraries, etc. Wind-catchers might be also used in places of high urban densities; hence their potential to provide natural ventilation is dependent on the presence of upstream structures. In this study, the two-sided wind-catcher model was based on a real wind-catcher observed in the city of Yazd, Iran. The present study focuses on the flow patterns around and inside the isolated two-sided wind-catcher, and on a two-sided wind-catcher in the presence of an upstream structure. The results show that the presence of an upstream structure influences the airflow pattern force and direction. Placing a high upstream structure reverses the airflow direction inside the wind-catcher.