Abstract: This work focuses on analysis of classical heat transfer equation regularized with Maxwell-Cattaneo transfer law. Computer simulations are performed in MATLAB environment. Numerical experiments are first developed on classical Fourier equation, then Maxwell-Cattaneo law is considered. Corresponding equation is regularized with a balancing diffusion term to stabilize discretizing scheme with adjusted time and space numerical steps. Several cases including a convective term in model equations are discussed, and results are given. It is shown that limiting conditions on regularizing parameters have to be satisfied in convective case for Maxwell-Cattaneo regularization to give physically acceptable solutions. In all valid cases, uniform convergence to solution of initial heat equation with Fourier law is observed, even in nonlinear case.
Abstract: Many accidents were happened because of fast driving, habitual working overtime or tired spirit. This paper presents a solution of remote warning for vehicles collision avoidance using vehicular communication. The development system integrates dedicated short range communication (DSRC) and global position system (GPS) with embedded system into a powerful remote warning system. To transmit the vehicular information and broadcast vehicle position; DSRC communication technology is adopt as the bridge. The proposed system is divided into two parts of the positioning andvehicular units in a vehicle. The positioning unit is used to provide the position and heading information from GPS module, and furthermore the vehicular unit is used to receive the break, throttle, and othersignals via controller area network (CAN) interface connected to each mechanism. The mobile hardware are built with an embedded system using X86 processor in Linux system. A vehicle is communicated with other vehicles via DSRC in non-addressed protocol with wireless access in vehicular environments (WAVE) short message protocol. From the position data and vehicular information, this paper provided a conflict detection algorithm to do time separation and remote warning with error bubble consideration. And the warning information is on-line displayed in the screen. This system is able to enhance driver assistance service and realize critical safety by using vehicular information from the neighbor vehicles.KeywordsDedicated short range communication, GPS, Control area network, Collision avoidance warning system.
Abstract: The major goal in defining and examining game
scenarios is to find good strategies as solutions to the game. A
plausible solution is a recommendation to the players on how to play
the game, which is represented as strategies guided by the various
choices available to the players. These choices invariably compel the
players (decision makers) to execute an action following some
conscious tactics. In this paper, we proposed a refinement-based
heuristic as a machine learning technique for human-like decision
making in playing Ayo game. The result showed that our machine
learning technique is more adaptable and more responsive in making
decision than human intelligence. The technique has the advantage
that a search is astutely conducted in a shallow horizon game tree.
Our simulation was tested against Awale shareware and an appealing
result was obtained.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: In this work, the precipitation of asphaltene from a Malaysian light oil reservoir was studies. A series of experiments were designed and carried out to examine the effect of CO2 injection on asphaltene precipitation. Different pressures of injections were used in Dynamic flooding experiment in order to investigate the effect of pressure versus injection pore volume of CO2. These dynamic displacement tests simulate reservoir condition. Results show that by increasing the pore volume of injected gas asphaltene precipitation will increases, also rise in injection pressure causes less precipitation. Sandstone core plug was used to represent reservoir formation during displacement test; therefore it made it possible to study the effect of present of asphaltene on formation. It is found out that the precipitated asphaltene can reduce permeability and porosity which is not favorable during oil production.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: The existing information system (IS) developments
methods are not met the requirements to resolve the security related
IS problems and they fail to provide a successful integration of
security and systems engineering during all development process
stages. Hence, the security should be considered during the whole
software development process and identified with the requirements
specification. This paper aims to propose an integrated security and
IS engineering approach in all software development process stages
by using i* language. This proposed framework categorizes into three
separate parts: modelling business environment part, modelling
information technology system part and modelling IS security part.
The results show that considering security IS goals in the whole
system development process can have a positive influence on system
implementation and better meet business expectations.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: We consider optimal channel equalization for MIMO
(multi-input/multi-output) time-varying channels in the sense of
MMSE (minimum mean-squared-error), where the observation noise
can be non-stationary. We show that all ZF (zero-forcing) receivers
can be parameterized in an affine form which eliminates completely
the ISI (inter-symbol-interference), and optimal channel equalizers
can be designed through minimization of the MSE (mean-squarederror)
between the detected signals and the transmitted signals,
among all ZF receivers. We demonstrate that the optimal channel
equalizer is a modified Kalman filter, and show that under the AWGN
(additive white Gaussian noise) assumption, the proposed optimal
channel equalizer minimizes the BER (bit error rate) among all
possible ZF receivers. Our results are applicable to optimal channel
equalization for DWMT (discrete wavelet multitone), multirate transmultiplexers,
OFDM (orthogonal frequency division multiplexing),
and DS (direct sequence) CDMA (code division multiple access)
wireless data communication systems. A design algorithm for optimal
channel equalization is developed, and several simulation examples
are worked out to illustrate the proposed design algorithm.
Abstract: An enhanced particle swarm optimization algorithm
(PSO) is presented in this work to solve the non-convex OPF
problem that has both discrete and continuous optimization variables.
The objective functions considered are the conventional quadratic
function and the augmented quadratic function. The latter model
presents non-differentiable and non-convex regions that challenge
most gradient-based optimization algorithms. The optimization
variables to be optimized are the generator real power outputs and
voltage magnitudes, discrete transformer tap settings, and discrete
reactive power injections due to capacitor banks. The set of equality
constraints taken into account are the power flow equations while the
inequality ones are the limits of the real and reactive power of the
generators, voltage magnitude at each bus, transformer tap settings,
and capacitor banks reactive power injections. The proposed
algorithm combines PSO with Newton-Raphson algorithm to
minimize the fuel cost function. The IEEE 30-bus system with six
generating units is used to test the proposed algorithm. Several cases
were investigated to test and validate the consistency of detecting
optimal or near optimal solution for each objective. Results are
compared to solutions obtained using sequential quadratic
programming and Genetic Algorithms.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: In this research saffron samples were prepared from
farms and sampling was done in four states contain : sampling from
fresh saffron of petal with forceps , sampling from fresh saffron of
petal by hands, sampling from dried sample by warm air in shadow,
sampling from dried sample which dried by dryer. Samples collected
and kept in sterile tubes and containers and carried to laboratory and
maintained until experiment. Microbial experiments were performed
to determine microbial load such as total count, Staphylococcus
aureus, coli form, E.coli, mold and yeast. Results showed that in
picking and drying stages the contamination amount increases in
saffron samples. There was a significant difference between the
microbial load of picked up saffron by forceps and by hands, and
also between dried saffron by warm air in shadow and by dryer.
Abstract: Information is power. Geographical information is an
emerging science that is advancing the development of knowledge to
further help in the understanding of the relationship of “place" with
other disciplines such as crime. The researchers used crime data for
the years 2004 to 2007 from the Baguio City Police Office to
determine the incidence and actual locations of crime hotspots.
Combined qualitative and quantitative research methodology was
employed through extensive fieldwork and observation, geographic
visualization with Geographic Information Systems (GIS) and Global
Positioning Systems (GPS), and data mining. The paper discusses
emerging geographic visualization and data mining tools and
methodologies that can be used to generate baseline data for
environmental initiatives such as urban renewal and rejuvenation.
The study was able to demonstrate that crime hotspots can be
computed and were seen to be occurring to some select places in the
Central Business District (CBD) of Baguio City. It was observed that
some characteristics of the hotspot places- physical design and milieu
may play an important role in creating opportunities for crime. A list
of these environmental attributes was generated. This derived
information may be used to guide the design or redesign of the urban
environment of the City to be able to reduce crime and at the same
time improve it physically.
Abstract: Zero inflated strict arcsine model is a newly developed
model which is found to be appropriate in modeling overdispersed
count data. In this study, we extend zero inflated strict arcsine model
to zero inflated strict arcsine regression model by taking into
consideration the extra variability caused by extra zeros and
covariates in count data. Maximum likelihood estimation method is
used in estimating the parameters for this zero inflated strict arcsine
regression model.
Abstract: Next generation networks with the idea of convergence of service and control layer in existing networks (fixed, mobile and data) and with the intention of providing services in an integrated network, has opened new horizon for telecom operators. On the other hand, economic problems have caused operators to look for new source of income including consider new services, subscription of more users and their promotion in using morenetwork resources and easy participation of service providers or 3rd party operators in utilizing networks. With this requirement, an architecture based on next generation objectives for service layer is necessary. In this paper, a new architecture based on IMS model explains participation of 3rd party operators in creation and implementation of services on an integrated telecom network.
Abstract: A feed-forward, back-propagation Artificial Neural
Network (ANN) model has been used to forecast the occurrences of
wastewater overflows in a combined sewerage reticulation system.
This approach was tested to evaluate its applicability as a method
alternative to the common practice of developing a complete
conceptual, mathematical hydrological-hydraulic model for the
sewerage system to enable such forecasts. The ANN approach
obviates the need for a-priori understanding and representation of the
underlying hydrological hydraulic phenomena in mathematical terms
but enables learning the characteristics of a sewer overflow from the
historical data.
The performance of the standard feed-forward, back-propagation
of error algorithm was enhanced by a modified data normalizing
technique that enabled the ANN model to extrapolate into the
territory that was unseen by the training data. The algorithm and the
data normalizing method are presented along with the ANN model
output results that indicate a good accuracy in the forecasted sewer
overflow rates. However, it was revealed that the accurate
forecasting of the overflow rates are heavily dependent on the
availability of a real-time flow monitoring at the overflow structure
to provide antecedent flow rate data. The ability of the ANN to
forecast the overflow rates without the antecedent flow rates (as is
the case with traditional conceptual reticulation models) was found to
be quite poor.
Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.