Abstract: This study intends to improve the bond performance of the polypropylene fiber used as reinforcing fiber for concrete by changing its shape into double crimped type through the enhancement its fabrication process. The bond performance of such double crimped fiber is evaluated by applying the JCI SF-8 (dog-bone shape) testing method. The test results reveal that the double crimped fiber develops bond performance improved by more than 19% compared to the conventional crimped type fiber.
Abstract: The objective of this study is to present and to analyze the feasibility of using steel fibers as reinforcement in the cementations matrix to minimize the effect of free shrinkage which is a major cause of cracks that have can observe on concrete structures, also to improve the mechanical resistances of this concrete reinforced. The experimental study was performed on specimens with geometric characteristics adapted to the testing. The tests of shrinkage apply on prismatic specimens, equipped with rods fixed to the ends with different dosages of fibers, it should be noted that the fibers used are hooked end of 50mm length and 67 slenderness. The results show that the compressive strength and flexural strength increases as the degree of incorporation of fibbers increases. And the shrinkage deformations are generally less important for fibers-reinforced concrete to those appearing in the concrete without fibers.
Abstract: Natural fibers are considered to have potential use as reinforcing agents in polymer composite materials because of their principal benefits: moderate strength and stiffness, low cost, and being an environmental friendly, degradable, and renewable material. A study has been carried out to evaluate impact properties of composites made by areca fibers reinforced urea formaldehyde, melamine urea formaldehyde and epoxy resins. The extracted areca fibers from the areca husk were alkali treated with potassium hydroxide (KOH) to obtain better interfacial bonding between fiber and matrix. Then composites were produced by means of compression molding technique with varying process parameters, such as fiber condition (untreated and alkali treated), and fiber loading percentages (50% and 60% by weight). The developed areca fiber reinforced composites were then characterized by impact test. The results show that, impact strength increase with increase in the loading percentage. It is observed that, treated areca fiber reinforcement increases impact strength when compared to untreated areca fiber reinforcement.
Abstract: At highly congested reinforcement regions, which is common at beam-column joint area, clear spacing between parallel bars becomes less than maximum normal aggregate size (20mm) which has not been addressed in any design code and specifications. Limited clear spacing between parallel bars (herein after thin cover) is one of the causes which affect anchorage performance. In this study, an experimental investigation was carried out to understand anchorage performance of reinforcement in Self-Compacting Concrete (SCC) and Normal Concrete (NC) at highly congested regions under uni-axial tensile loading. Column bar was pullout whereas; beam bars were offset from column reinforcement creating thin cover as per site condition. Two different sizes of coarse aggregate were used for NC (20mm and 10mm). Strain gauges were also installed along the bar in some specimens to understand the internal stress mechanism. Test results reveal that anchorage performance is affected at highly congested reinforcement region in NC with maximum aggregate size 20mm whereas; SCC and Small Aggregate (10mm) gives better structural performance.
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.
Abstract: Generalization is one of the most challenging issues
of Learning Classifier Systems. This feature depends on the
representation method which the system used. Considering the
proposed representation schemes for Learning Classifier System, it
can be concluded that many of them are designed to describe the
shape of the region which the environmental states belong and the
other relations of the environmental state with that region was
ignored. In this paper, we propose a new representation scheme
which is designed to show various relationships between the
environmental state and the region that is specified with a particular
classifier.
Abstract: When dealing with safety in structures, the connections between structural components play an important role. Robustness of a structure as a whole depends both on the load- bearing capacity of the structural component and on the structures capacity to resist total failure, even though a local failure occurs in a component or a connection between components. To avoid progressive collapse it is necessary to be able to carry out a design for connections. A connection may be executed with anchors to withstand local failure of the connection in structures built with prefabricated components. For the design of these anchors, a model is developed for connections in structures performed in prefabricated autoclaved aerated concrete components. The design model takes into account the effect of anchors placed close to the edge, which may result in splitting failure. Further the model is developed to consider the effect of reinforcement diameter and anchor depth. The model is analytical and theoretically derived assuming a static equilibrium stress distribution along the anchor. The theory is compared to laboratory test, including the relevant parameters and the model is refined and theoretically argued analyzing the observed test results. The method presented can be used to improve safety in structures or even optimize the design of the connections
Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Abstract: Textile structures are engineered and fabricated to
meet worldwide structural applications. Nevertheless, research
varying textile structure on natural fibre as composite reinforcement
was found to be very limited. Most of the research is focusing on
short fibre and random discontinuous orientation of the reinforcement
structure. Realizing that natural fibre (NF) composite had been
widely developed to be used as synthetic fibre composite
replacement, this research attempted to examine the influence of
woven and cross-ply laminated structure towards its mechanical
performances. Laminated natural fibre composites were developed
using hand lay-up and vacuum bagging technique. Impact and
flexural strength were investigated as a function of fibre type (coir
and kenaf) and reinforcement structure (imbalanced plain woven,
0°/90° cross-ply and +45°/-45° cross-ply). Multi-level full factorial
design of experiment (DOE) and analysis of variance (ANOVA) was
employed to impart data as to how fibre type and reinforcement
structure parameters affect the mechanical properties of the
composites. This systematic experimentation has led to determination
of significant factors that predominant influences the impact and
flexural properties of the textile composites. It was proven that both
fibre type and reinforcement structure demonstrated significant
difference results. Overall results indicated that coir composite and
woven structure exhibited better impact and flexural strength. Yet,
cross-ply composite structure demonstrated better fracture resistance.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: A numerical analysis of a reinforced concrete (RC) wall under missile impact loading is presented in this study. The model created by Technical Research Center of Finland was used. The commercial finite element code, LS-DYNA was used to analyze. The structural components of the reinforced concrete wall, missile and their contacts are fully modeled. The material nonlinearity with strain rate effects considering damage and failure is included in the analysis. The results of analysis were verified with other research results. The case-studies with different reinforcement ratios were conducted to investigate the influence of reinforcement on the punching behavior of walls under missile impact.
Abstract: Chloride induced corrosion of steel reinforcement is
the main cause of deterioration of reinforced concrete marine
structures. This paper investigates the relative performance of
alternative repair options with respect to the deterioration of
reinforced concrete bridge elements in marine environments. Focus is
placed on the initiation phase of reinforcement corrosion. A
laboratory study is described which involved exposing concrete
samples to accelerated chloride-ion ingress. The study examined the
relative efficiencies of two repair methods, namely Ordinary Portland
Cement (OPC) concrete and a concrete which utilised Ground
Granulated Blastfurnace Cement (GGBS) as a partial cement
replacement. The mix designs and materials utilised were identical to
those implemented in the repair of a marine bridge on the South East
coast of Ireland in 2007. The results of this testing regime serve to
inform input variables employed in probabilistic modelling of
deterioration for subsequent reliability based analysis to compare the
relative performance of the studied repair options.
Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.