Abstract: This paper develops models to analyze the
relationship between leisure time and wage change. Using Thailand-s
Time Use Survey and Labor Force Survey data, the estimation of
wage changes in response to leisure time change indicates that media
receiving, personal care and social participation and volunteer
activities are the ones that significantly raise hourly wages. Thus, the
finding suggests the stimulation in time use for media access to
enhance knowledge and productivity, personal care for attractiveness
and healthiness in order to raise productivity, and social activities to
develop connections for possible future opportunities including wage
increase. These activities should be promoted for productive leisure
time and for welfare improvement.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: Cutting tools are widely used in manufacturing processes and drilling is the most commonly used machining process. Although drill-bits used in drilling may not be expensive, their breakage can cause damage to expensive work piece being drilled and at the same time has major impact on productivity. Predicting drill-bit breakage, therefore, is important in reducing cost and improving productivity. This study uses twenty features extracted from two degradation signals viz., thrust force and torque. The methodology used involves developing and comparing decision tree, random forest, and multinomial logistic regression models for classifying and predicting drill-bit breakage using degradation signals.
Abstract: Organizations face challenges supporting knowledge
workers due to their particular requirements for an environment
supportive of their self-guided learning activities which are important
to increase their productivity and to develop creative solutions to
non-routine problems. Face-to-face knowledge sharing remains
crucial in spite of a large number of knowledge management
instruments that aim at supporting a more impersonal transfer of
knowledge. This paper first describes the main criteria for a
conceptual and technical solution targeted at flexible management of
office space that aims at assigning those knowledge workers to the
same room that are most likely to thrive when being brought together
thus enhancing their knowledge work productivity. The paper
reflects on lessons learned from the implementation and operation of
such a solution in a project-focused organization and derives several
implications for future extensions that target to foster problem
solving, informal learning and personal development.
Abstract: this article proposed a methodology for computer
numerical control (CNC) machine scoring. The case study company
is a manufacturer of hard disk drive parts in Thailand. In this
company, sample of parts manufactured from CNC machine are
usually taken randomly for quality inspection. These inspection data
were used to make a decision to shut down the machine if it has
tendency to produce parts that are out of specification. Large amount
of data are produced in this process and data mining could be very
useful technique in analyzing them. In this research, data mining
techniques were used to construct a machine scoring model called
'machine priority assessment model (MPAM)'. This model helps to
ensure that the machine with higher risk of producing defective parts
be inspected before those with lower risk. If the defective prone
machine is identified sooner, defective part and rework could be
reduced hence improving the overall productivity. The results
showed that the proposed method can be successfully implemented
and approximately 351,000 baht of opportunity cost could have
saved in the case study company.
Abstract: Today, the working areas put forward the administration of change. In order to provide this; it is required from the organizations to be creative. Professional creativity in offices depends on an environment that enables the development of the organization only after the individual or collective exertions within the organization. By providing this environment, the organization will gain efficiency, productivity, and work pleasure. In order to bring up the workforce appropriate to the related expectations, the professional creativity of the office management and secretarial profession candidates should be evaluated, education programs appropriate to this and related directly with the service quality should be prepared and the future of this profession should be directed. The aim of this study is to ensure the attention to improve the prepared education program as well as the creative thoughts and their applications, when carrying out an office management and secretarial training. 144 students took place in this research and a questionnaire of 48 questions was carried out.
Abstract: In this paper developed and realized absolutely new
algorithm for solving three-dimensional Poisson equation. This
equation used in research of turbulent mixing, computational fluid
dynamics, atmospheric front, and ocean flows and so on. Moreover in
the view of rising productivity of difficult calculation there was
applied the most up-to-date and the most effective parallel
programming technology - MPI in combination with OpenMP
direction, that allows to realize problems with very large data
content. Resulted products can be used in solving of important
applications and fundamental problems in mathematics and physics.
Abstract: The possibility of radionuclides-related contamination
of lands at agricultural holdings defines the necessity to apply special
protective measures in plant growing. The aim of researches is to
elucidate the influence of polymers applying on biological migration
of man-made anthropogenic radionuclides 90Sr and 137Cs in the
system water - soil – plant. The tests are being carried out under field
conditions with and without application of polymers in root-inhabited
media in more radioecological tension zone (with the radius of 7 km
from the Armenian Nuclear Power Plant). The polymers on the base
of K+, Caµ, KµCaµ ions were tested. Productivity of pepper
depending on the presence and type of polymer material, content of
artificial radionuclides in waters, soil and plant material has been
determined. The character of different polymers influence on the
artificial radionuclides migration and accumulation in the system
water-soil-plant and accumulation in the plants has been cleared up.
Abstract: True integration of multimedia services over wired or
wireless networks increase the productivity and effectiveness in
today-s networks. IP Multimedia Subsystems are Next Generation
Network architecture to provide the multimedia services over fixed
or mobile networks. This paper proposes an extended SIP-based QoS
Management architecture for IMS services over underlying IP access
networks. To guarantee the end-to-end QoS for IMS services in
interconnection backbone, SIP based proxy Modules are introduced
to support the QoS provisioning and to reduce the handoff disruption
time over IP access networks. In our approach these SIP Modules
implement the combination of Diffserv and MPLS QoS mechanisms
to assure the guaranteed QoS for real-time multimedia services. To
guarantee QoS over access networks, SIP Modules make QoS
resource reservations in advance to provide best QoS to IMS users
over heterogeneous networks. To obtain more reliable multimedia
services, our approach allows the use of SCTP protocol over SIP
instead of UDP due to its multi-streaming feature. This architecture
enables QoS provisioning for IMS roaming users to differentiate IMS
network from other common IP networks for transmission of realtime
multimedia services. To validate our approach simulation
models are developed on short scale basis. The results show that our
approach yields comparable performance for efficient delivery of
IMS services over heterogeneous IP access networks.
Abstract: The requirement to improve software productivity has
promoted the research on software metric technology. There are
metrics for identifying the quality of reusable components but the
function that makes use of these metrics to find reusability of
software components is still not clear. These metrics if identified in
the design phase or even in the coding phase can help us to reduce the
rework by improving quality of reuse of the component and hence
improve the productivity due to probabilistic increase in the reuse
level. CK metric suit is most widely used metrics for the objectoriented
(OO) software; we critically analyzed the CK metrics, tried
to remove the inconsistencies and devised the framework of metrics
to obtain the structural analysis of OO-based software components.
Neural network can learn new relationships with new input data and
can be used to refine fuzzy rules to create fuzzy adaptive system.
Hence, Neuro-fuzzy inference engine can be used to evaluate the
reusability of OO-based component using its structural attributes as
inputs. In this paper, an algorithm has been proposed in which the
inputs can be given to Neuro-fuzzy system in form of tuned WMC,
DIT, NOC, CBO , LCOM values of the OO software component and
output can be obtained in terms of reusability. The developed
reusability model has produced high precision results as expected by
the human experts.
Abstract: Manufacturing, production and service industries within Libya have struggled with many problems during the past two decades due to many difficulties. These problems have created a negative impact on the productivity and utilization of many industries around the country. This paper studies the implementation levels of the manufacturing control systems known as Manufacturing Resource Planning (MRPII) being adapted within some Libyan industries. A survey methodology has been applied for this research, based on the survey analysis, the results pointed out that the system within these industries has a modest strategy towards most of the areas that are considered as being very crucial in implementing these systems successfully. The findings also show a variation within these implementation levels with a respect to the key-elements that related to MRPII, giving the highest levels in the emphasise on financial data accuracy. The paper has also identified limitations within the investigated manufacturing and managerial areas and has pointed to where senior managers should take immediate actions in order to achieve effective implementation of MRPII within their business area.
Abstract: The six sigma method is a project-driven management approach to improve the organization-s products, services, and processes by continually reducing defects in the organization. Understanding the key features, obstacles, and shortcomings of the six sigma method allows organizations to better support their strategic directions, and increasing needs for coaching, mentoring, and training. It also provides opportunities to better implement six sigma projects. The purpose of this paper is the survey of six sigma process and its impact on the organizational productivity. So I have studied key concepts , problem solving process of six sigmaas well as the survey of important fields such as: DMAIC, six sigma and productivity applied programme, and other advantages of six sigma. In the end of this paper, present research conclusions. (direct and positive relation between six sigma and productivity)
Abstract: Growing world population has fundamental impacts
and often catastrophic on natural habitat. The immethodical
consumption of energy, destruction of the forests and extinction of
plant and animal species are the consequence of this experience.
Urban sustainability and sustainable urban development, that is so
spoken these days, should be considered as a strategy, goal and
policy, beyond just considering environmental issues and protection.
The desert-s climate has made a bunch of problems for its residents.
Very hot and dry climate in summers of the Iranian desert areas,
when there was no access to modern energy source and mechanical
cooling systems in the past, made Iranian architects to design a
natural ventilation system in their buildings. The structure, like a
tower going upward the roof, besides its ornamental application and
giving a beautiful view to the building, was used as a spontaneous
ventilation system. In this paper, it has been tried to name the
problems of the area and it-s inconvenience, then some answers has
pointed out in order to solve the problems and as an alternative
solution BADGIR (wind-catcher) has been introduced as a solution
knowing that it has been playing a major role in dealing with the
problems.
Abstract: International markets driven forces are changing
continuously, therefore companies need to gain a competitive edge in
such markets. Improving the company's products, processes and
practices is no longer auxiliary. Lean production is a production
management philosophy that consolidates work tasks with minimum
waste resulting in improved productivity. Lean production practices
can be mapped into many production areas. One of these is
Manufacturing Equipment and Technology (MET). Many lean
production practices can be implemented in MET, namely, specific
equipment configurations, total preventive maintenance, visual
control, new equipment/ technologies, production process
reengineering and shared vision of perfection.The purpose of this
paper is to investigate the implementation level of these six practices
in Jordanian industries. To achieve that a questionnaire survey has
been designed according to five-point Likert scale. The questionnaire
is validated through pilot study and through experts review. A sample
of 350 Jordanian companies were surveyed, the response rate was
83%. The respondents were asked to rate the extent of
implementation for each of practices. A relationship conceptual
model is developed, hypotheses are proposed, and consequently the
essential statistical analyses are then performed. An assessment tool
that enables management to monitor the progress and the
effectiveness of lean practices implementation is designed and
presented. Consequently, the results show that the average
implementation level of lean practices in MET is 77%, Jordanian
companies are implementing successfully the considered lean
production practices, and the presented model has Cronbach-s alpha
value of 0.87 which is good evidence on model consistency and
results validation.
Abstract: Higher productivity and less cost in the ship
manufacturing process are required to maintain the international
competitiveness of morden manufacturing industries. In shipbuilding,
however, the Engineering To Order (ETO) production method and
production process is very difficult. Thus, designs change frequently.
In accordance with production, planning should be set up according
to scene changes. Therefore, fixed production planning is very
difficult. Thus, a scheduler must first make sketchy plans, then
change the plans based on the work progress and modifications.
Thus, data sharing in a shipbuilding block assembly shop is very
important. In this paper, we proposed to scheduling method
applicable to the shipbuilding industry and decision making support
system through web based visualization system.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: Banishing hunger from the face of earth has been
frequently expressed in various international, national and regional
level conferences since 1974. Providing food security has become
important issue across the world particularly in developing countries.
In a developing country like India, where growth rate of population is
more than that of the food grains production, food security is a
question of great concern. According to the International Food Policy
Research Institute's Global Hunger Index, 2011, India ranks 67 of the
81 countries of the world with the worst food security status. After
Green Revolution, India became a food surplus country. Its
production has increased from 74.23 million tonnes in 1966-67 to
257.44 million tonnes in 2011-12. But after achieving selfsufficiency
in food during last three decades, the country is now
facing new challenges due to increasing population, climate change,
stagnation in farm productivity. Therefore, the main objective of the
present paper is to examine the food security situation at national
level in the country and further to explain the paradox of food
insecurity in a food surplus state of India i.e in Punjab at micro level.
In order to achieve the said objectives, secondary data collected from
the Ministry of Agriculture and the Agriculture department of Punjab
State was analyzed. The result of the study showed that despite
having surplus food production the country is still facing food
insecurity problem at micro level. Within the Kandi belt of Punjab
state, the area adjacent to plains is food secure while the area along
the hills falls in food insecure zone.
The present paper is divided into following three sections (i)
Introduction, (ii) Analysis of food security situation at national level
as well as micro level (Kandi belt of Punjab State) (iii) Concluding
Observations
Abstract: The traditional software product and process metrics
are neither suitable nor sufficient in measuring the complexity of
software components, which ultimately is necessary for quality and
productivity improvement within organizations adopting CBSE.
Researchers have proposed a wide range of complexity metrics for
software systems. However, these metrics are not sufficient for
components and component-based system and are restricted to the
module-oriented systems and object-oriented systems. In this
proposed study it is proposed to find the complexity of the JavaBean
Software Components as a reflection of its quality and the component
can be adopted accordingly to make it more reusable. The proposed
metric involves only the design issues of the component and does not
consider the packaging and the deployment complexity. In this way,
the software components could be kept in certain limit which in turn
help in enhancing the quality and productivity.