Abstract: Modeling and simulation of fixed bed three-phase
catalytic reactors are considered for wet air catalytic oxidation of
phenol to perform a comparative numerical analysis between tricklebed
and packed-bubble column reactors. The modeling involves
material balances both for the catalyst particle as well as for different
fluid phases. Catalyst deactivation is also considered in a transient
reactor model to investigate the effects of various parameters
including reactor temperature on catalyst deactivation. The
simulation results indicated that packed-bubble columns were
slightly superior in performance than trickle beds. It was also found
that reaction temperature was the most effective parameter in catalyst
deactivation.
Abstract: A novel typical day prediction model have been built and validated by the measured data of a grid-connected solar photovoltaic (PV) system in Macau. Unlike conventional statistical method used by previous study on PV systems which get results by averaging nearby continuous points, the present typical day statistical method obtain the value at every minute in a typical day by averaging discontinuous points at the same minute in different days. This typical day statistical method based on discontinuous point averaging makes it possible for us to obtain the Gaussian shape dynamical distributions for solar irradiance and output power in a yearly or monthly typical day. Based on the yearly typical day statistical analysis results, the maximum possible accumulated output energy in a year with on site climate conditions and the corresponding optimal PV system running time are obtained. Periodic Gaussian shape prediction models for solar irradiance, output energy and system energy efficiency have been built and their coefficients have been determined based on the yearly, maximum and minimum monthly typical day Gaussian distribution parameters, which are obtained from iterations for minimum Root Mean Squared Deviation (RMSD). With the present model, the dynamical effects due to time difference in a day are kept and the day to day uncertainty due to weather changing are smoothed but still included. The periodic Gaussian shape correlations for solar irradiance, output power and system energy efficiency have been compared favorably with data of the PV system in Macau and proved to be an improvement than previous models.
Abstract: Prostate cancer is one of the most frequent cancers in men and is a major cause of mortality in the most of countries. In many diagnostic and treatment procedures for prostate disease accurate detection of prostate boundaries in transrectal ultrasound (TRUS) images is required. This is a challenging and difficult task due to weak prostate boundaries, speckle noise and the short range of gray levels. In this paper a novel method for automatic prostate segmentation in TRUS images is presented. This method involves preprocessing (edge preserving noise reduction and smoothing) and prostate segmentation. The speckle reduction has been achieved by using stick filter and top-hat transform has been implemented for smoothing. A feed forward neural network and local binary pattern together have been use to find a point inside prostate object. Finally the boundary of prostate is extracted by the inside point and an active contour algorithm. A numbers of experiments are conducted to validate this method and results showed that this new algorithm extracted the prostate boundary with MSE less than 4.6% relative to boundary provided manually by physicians.
Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: The objective of the present communication is to
develop new genuine exponentiated mean codeword lengths and to
study deeply the problem of correspondence between well known
measures of entropy and mean codeword lengths. With the help of
some standard measures of entropy, we have illustrated such a
correspondence. In literature, we usually come across many
inequalities which are frequently used in information theory.
Keeping this idea in mind, we have developed such inequalities via
coding theory approach.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: As business environments are rapidly changing,
the manufacturing system must be reconfigured to adapt to
various customer needs. In order to cope with this challenge, it
is quintessential to test industrial control logic rapidly and
easily in the design time, and monitor operational behavior in
the run time of automated manufacturing system. Proposed
integrated model for virtual prototyping and operational
monitoring of industrial control logic is to improve limitations
of current ladder programming practices and general discrete
event simulation method. Each plant layout model using HMI
package and object-oriented control logic model is designed
independently and is executed simultaneously in integrated
manner to reflect design practices of automation system in the
design time. Control logic is designed and executed using UML
activity diagram without considering complicated control
behavior to deal with current trend of reconfigurable
manufacturing. After the physical installation, layout model of
virtual prototype constructed in the design time is reused for
operational monitoring of system behavior during run time.
Abstract: The peculiarities of the nanoscale structure-phase
states formed after electroexplosive carburizing and subsequent
electron-beam treatment of technically pure titanium surface in different regimes are established by methods of transmission electron
diffraction microscopy and physical mechanisms are discussed. Electroexplosive carburizing leads to surface layer formation
(40 m thickness) with increased (in 3.5 times) microhardness. It consists of β-titanium, graphite (monocrystals 100-150 nm,
polycrystals 5-10 nm, amorphous particles 3-5nm), TiC (5-10 nm), β-Ti02 (2-20nm). After electron-beam treatment additionally increasing the microhardness the surface layer consists of TiC.
Abstract: The counting and analysis of blood cells allows the
evaluation and diagnosis of a vast number of diseases. In particular,
the analysis of white blood cells (WBCs) is a topic of great interest to
hematologists. Nowadays the morphological analysis of blood cells is
performed manually by skilled operators. This involves numerous
drawbacks, such as slowness of the analysis and a nonstandard
accuracy, dependent on the operator skills. In literature there are only
few examples of automated systems in order to analyze the white
blood cells, most of which only partial. This paper presents a
complete and fully automatic method for white blood cells
identification from microscopic images. The proposed method firstly
individuates white blood cells from which, subsequently, nucleus and
cytoplasm are extracted. The whole work has been developed using
MATLAB environment, in particular the Image Processing Toolbox.
Abstract: Biodiesel as an alternative fuel for diesel engines has been developed for some three decades now. While it is gaining wide acceptance in Europe, USA and some parts of Asia, the same cannot be said of Africa. With more than 35 countries in the continent depending on imported crude oil, it is necessary to look for alternative fuels which can be produced from resources available locally within any country. Hence this study presents performance of single cylinder diesel engine using blends of shea butter biodiesel. Shea butter was transformed into biodiesel by transesterification process. Tests are conducted to compare the biodiesel with baseline diesel fuel in terms of engine performance and exhaust emission characteristics. The results obtained showed that the addition of biodiesel to diesel fuel decreases the brake thermal efficiency (BTE) and increases the brake specific fuel consumption (BSFC). These results are expected due to the lower energy content of biodiesel fuel. On the other hand while the NOx emissions increased with increase in biodiesel content in the fuel blends, the emissions of carbon monoxide (CO), un-burnt hydrocarbon (UHC) and smoke opacity decreased. The engine performance which indicates that the biodiesel has properties and characteristics similar to diesel fuel and the reductions in exhaust emissions make shea butter biodiesel a viable additive or substitute to diesel fuel.
Abstract: A new technique based on Pattern search optimization is proposed for estimating different solar cell parameters in this paper. The estimated parameters are the generated photocurrent, saturation current, series resistance, shunt resistance, and ideality factor. The proposed approach is tested and validated using double diode model to show its potential. Performance of the developed approach is quite interesting which signifies its potential as a promising estimation tool.
Abstract: The recent development of humanoid robots has led robot designers to imagine a great variety of anthropomorphic forms for human-like machine. Which form is the best ? We try to answer this question from a double meaning of the anthropomorphism : a positive anthropomorphism corresponing to the realization of an effective anthropomorphic form object and a negative one corresponding to our natural tendency in certain circumstances to give human attributes to non-human beings. We postulate that any humanoid robot is concerned by both these two anthropomorphism kinds. We propose to use gestalt theory and Heider-s balance theory in order to analyze how negative anthropomorphism can influence our perception of human-like robots. From our theoretical approach we conclude that an “even shape" as defined by gestalt theory is not a sufficient condition for a good integration of future humanoid robots into a human community. Aesthetic perception of the robot cannot be splitted from a social perception : a humanoid robot, any how the efforts made for improving its appearance, could be rejected if it is devoted to a task with too high affective implications.
Abstract: The purpose of this study was to develop and examine a
Teaching Commitment Scale of Health and Physical Education
(TCS-HPE) for Taiwanese elementary school teachers. First of all,
based on teaching commitment related theory and literatures to
develop a original scale with 40 items, later both stratified random
sampling and cluster sampling were used to sample participants.
During the first stage, 300 teachers were sampled and 251 valid scales
(83.7%) returned. Later, the data was analyzed by exploratory factor
analysis to obtain 74.30% of total variance for the construct validity.
The Cronbach-s alpha coefficient of sum scale reliability was 0.94, and
subscale coefficients were between 0.80 and 0.96. In the second stage,
400 teachers were sampled and 318 valid scales (79.5%) returned.
Finally, this study used confirmatory factor analysis to test validity and
reliability of TCS-HPE. The result showed that the fit indexes reached
acceptable criteria(¤ç2
(246 ) =557.64 , p
Abstract: In this paper, a nonlinear model predictive swing-up
and stabilizing sliding controller is proposed for an inverted
pendulum-cart system. In the swing up phase, the nonlinear model
predictive control is formulated as a nonlinear programming problem
with energy based objective function. By solving this problem at
each sampling instant, a sequence of control inputs that optimize the
nonlinear objective function subject to various constraints over a
finite horizon are obtained. Then, this control drives the pendulum to
a predefined neighborhood of the upper equilibrium point, at where
sliding mode based model predictive control is used to stabilize the
systems with the specified constraints. It is shown by the simulations
that, due to the way of formulating the problem, short horizon
lengths are sufficient for attaining the swing up goal.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: In modern distributed software systems, the issue of communication among composing parts represents a critical point, but the idea of extending conventional programming languages with general purpose communication constructs seems difficult to realize. As a consequence, there is a (growing) gap between the abstraction level required by distributed applications and the concepts provided by platforms that enable communication. This work intends to discuss how the Model Driven Software Development approach can be considered as a mature technology to generate in automatic way the schematic part of applications related to communication, by providing at the same time high level specialized languages useful in all the phases of software production. To achieve the goal, a stack of languages (meta-meta¬models) has been introduced in order to describe – at different levels of abstraction – the collaborative behavior of generic entities in terms of communication actions related to a taxonomy of messages. Finally, the generation of platforms for communication is viewed as a form of specification of language semantics, that provides executable models of applications together with model-checking supports and effective runtime environments.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: During this day a considerable amount of Leachate is produced with high amounts of organic material and nutrients needed plants. This study has done in order to scrutinize the effect of Leachate compost on the pH, EC and organic matter percentage in the form of statistical Factorial plan through randomizing block design with three main and two minor treatments and also three replications during three six month periods. Major treatments include N: Irrigation with the region-s well water as a control, I: Frequent irrigation with well water and Leachate, C: Mixing Leachate and water well (25 percent leachate + 75 percent ordinary well water) and secondary treatments, include DI: surface drip irrigation and SDI: sub surface drip irrigation. Results of this study indicated significant differences between treatments and also there were mixing up with the control treatment in the reduction of pH, increasing soluble salts and also increasing the organic matter percentage. This increase is proportional to the amount of added Leachate and in the treatment also proportional to higher mixture of frequent treatment. Therefore, since creating an acidic pH increases the ability to absorb some nutrient elements such as phosphorus, iron, zinc, copper and manganese are increased and the other hand, organic materials also improve many physical and chemical properties of soil are used in Leachate trash Consider health issues as refined in the green belts around cities as a liquid fertilizer recommended.
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.