Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.
Abstract: In recent years, geographic information systems (GIS)
and remote sensing using has increased to estimate runoff catchment.
In this research, runoff curve number maps for captive catchment of
Tehran by helping GIS and also remote sensing which based on
factors such as vegetation, lands using, group of soil hydrology and
hydrological conditions were obtained. Runoff curve numbers map
was obtained by combining these maps in ARC GIS and SCS table.
To evaluate the accuracy of the results, the maximum flow rate of
flood which was obtained from curve numbers, was compared with
the measured maximum flood rate at the watershed outlet and
correctness of curve numbers were approved.
Abstract: Vibration analysis of most critical equipment is considered as one of the most challenging activities in preventive maintenance. Utilities are heart of the process in big industrial plants like petrochemical zones. Vibration analysis methods and condition monitoring systems of these kinds of equipments are developed too much in recent years. On the other hand, there are too much operation factors like inlet and outlet pressures and temperatures that should be monitored. In this paper, some of the most effective concepts and techniques related to gas turbine vibration analysis are discussed. In addition, a gas turbine SIEMENS 162MW - V94.2 vibration case history related to Iran power industry in Fars province is explained. Vibration monitoring system and machinery technical specification are introduced. Besides, absolute and relative vibration trends, turbine and compressor orbits, Fast Fourier transform (FFT) in absolute vibrations, vibration modal analysis, turbine and compressor start up and shut down conditions, bode diagrams for relative vibrations, Nyquist diagrams and waterfall or three-dimensional FFT diagrams in startup and trip conditions are discussed with relative graphs. Furthermore, Split Resonance in gas turbines is discussed in details. Moreover, some updated vibration monitoring system, blade manufacturing technique and modern damping mechanism are discussed in this paper.
Abstract: Emission regulations for diesel engines are being strengthened and it is impossible to meet the standards without exhaust after-treatment systems. Lack of the space in many diesel vehicles, however, make it difficult to design and install stand-alone catalytic converters such as DOC, DPF, and SCR in the vehicle exhaust systems. Accordingly, those have been installed inside the muffler to save the space, and referred to the catalytic muffler. However, that has complex internal structure with perforated plate and pipe for noise and monolithic catalyst for emission reduction. For this reason, flow uniformity and pressure drop, which affect efficiency of catalyst and engine performance, respectively, should be examined when the catalytic muffler is designed. In this work, therefore, the flow uniformity and pressure drop to improve the performance of the catalytic converter and the engine have been numerically investigated by changing various design parameters such as inlet shape, porosity, and outlet shape of the muffler using the three-dimensional turbulent flow of the incompressible, non-reacting, and steady state inside the catalytic muffler. Finally, it can be found that the shape, in which the muffler has perforated pipe inside the inlet part, has higher uniformity index and lower pressure drop than others considered in this work.
Abstract: Catalytic combustion is generally accepted as an environmentally preferred alternative for the generation of heat and power from fossil fuels mainly due to its advantages related to the stable combustion under very lean conditions with low emissions of NOx, CO, and UHC at temperatures lower than those occurred in conventional flame combustion. Despite these advantages, the commercial application of catalytic combustion has been delayed because of complicated reaction processes and the difficulty in developing appropriate catalysts with the required stability and durability. To develop the catalytic combustors, detailed studies on the combustion characteristics of catalytic combustion should be conducted. To the end, in current research, quantitative studies on the combustion characteristics of the catalytic combustors, with a Pd-based catalyst for MCFC power generation systems, relying on numerical simulations have been conducted. In addition, data from experimental studies of variations in outlet temperatures and fuel conversion, taken after operating conditions have been used to validate the present numerical approach. After introducing the governing equations for mass, momentum, and energy equations as well as a description of catalytic combustion kinetics, the effects of the excess air ratio, space velocity, and inlet gas temperature on the catalytic combustion characteristics are extensively investigated. Quantitative comparisons are also conducted with previous experimental data. Finally, some concluding remarks are presented.
Abstract: Ground Coupled Heat Pumps (GCHPs) exploit effectively the heat capacity of the ground, with the use of Ground Heat Exchangers (GHE). Depending on the mode of operation of the GCHPs, GHEs dissipate or absorb heat from the ground. For sizing the GHE the thermal properties of the ground need to be known. This paper gives information about the density, thermal conductivity, specific heat and thermal diffusivity of various lithologies encountered in Cyprus with various relations between these properties being examined through comparison and modeling. The results show that the most important correlation is the one encountered between thermal conductivity and thermal diffusivity with both properties showing similar response to the inlet and outlet flow temperature of vertical and horizontal heat exchangers.
Abstract: In this work, the bioclogging of two soils with different granulometries is presented. The durability of the clogging is also studied under cycles of hydraulic head and under cycles of desaturation-resaturation. The studied materials present continuous grain size distributions. The first one corresponding to the "material 1” presents grain sizes between 0.4 and 4mm. The second material called "material 2" is composed of grains with size varying between 1 and 10mm. The results show that clogging occurs very quickly after the injection of nutrition and an outlet flow near to 0 is observed. The critical hydraulic head is equal to 0.76 for "material 1", and 0.076 for "material 2". The durability tests show a good resistance to unclogging under cycles of hydraulic head and desaturation-resaturation for the "material 1". Indeed, the flow after the cycles is very low. In contrast, "material 2", shows a very bad resistance, especially under the hydraulic head cycles. The resistance under the cycles of desaturation-resaturation is better but an important increase of the flow is observed. The difference of behavior is due to the granulometry of the materials. Indeed, the large grain size contributes to the reduction of the efficiency of the bioclogging treatment in this material.
Abstract: Vibration analysis is the most important factor in preventive maintenance. Gas turbine vibration analysis is also one of the most challenging categories in most critical equipment monitoring systems. Utilities are heart of the process in big industrial plants like petrochemical zones. Vibration analysis methods and condition monitoring systems of this kind of equipment developed too much in recent years. On the other hand, too much operation condition consideration in this kind of equipment should be adjusted properly like inlet and outlet pressure and temperature for both turbine and compressor. In this paper the most important tools and hypothesis used for analyzing of gas turbine power plants discussed in details through a real case history related to an Alstom Typhoon gas turbine power plant in Iran oil industries. In addition, the basic principal of vibration behavior caused by mechanical unbalance in gas turbine rotor discussed in details.
Abstract: One of the Best Management Practices (BMPs) promoted in Urban Stormwater Management Manual for Malaysia (MSMA) published by the Department of Irrigation and Drainage (DID) in 2001 is through the construction of wet ponds in new development projects for water quantity and quality control. Therefore, this paper aims to demonstrate a case study on evaluation of a constructed mini wet pond located at Sekolah Rendah Kebangsaan Seksyen 2, Puchong, Selangor, Malaysia in both stormwater quantity and quality aspect particularly to reduce the peak discharge by temporary storing and gradual release of stormwater runoff from an outlet structure or other release mechanism. The evaluation technique will be using InfoWorks Collection System (CS) as the numerical modeling approach for water quantity aspect. Statistical test by comparing the correlation coefficient (R2), mean error (ME), mean absolute error (MAE) and root mean square error (RMSE) were used to evaluate the model in simulating the peak discharge changes. Results demonstrated that there will be a reduction in peak flow at 11 % to 15% and time to peak flow is slower by 5 minutes through a wet pond. For water quality aspect, a survey on biological indicator of water quality carried out depicts that the pond is within the range of rather clean to clean water with the score of 5.3. This study indicates that a constructed wet pond with wetland facilities is able to help in managing water quantity and stormwater generated pollution at source, towards achieving ecologically sustainable development in urban areas.
Abstract: The evaluation of the convective heat transfer of flow in passages with rectangular cross section is still of interest for the heat transfer investigators, as in the air heater solar collectors. The aim of this paper is to present investigation results on the natural convection heat transfer in a solar air heater. The effect of the channel length as heat transfer surface and the inclination of the passage were investigated. The results were obtained experimentally and theoretically. For that, an experimental test rig was fabricated with channel lengths of 1m, 1.5m, and 2m. For each length, the air outlet and inlet temperatures, absorber and cover temperatures, solar radiation intensity and air flow rate were measured at 10o, 30o, 50o, 70o, and 90o tilt angles. Measurements were recorded every 2 hours interval to investigate the transient behavior of the system. The experimental and theoretical results are presented in terms of Nu number versus Ra number and discussed. The percentages of differences between experimental and theoretical results are within the margin of 6% to 13%, effectively. It is recommended to extend the investigation to study the same configurations with different artificial surface roughing by ribs or pins.
Abstract: This study examines the stack ventilation performance of an office building located in Taipei, Taiwan. Atriums in this building act as stacks that facilitate buoyancy-driven ventilation. Computational Fluid Dynamic (CFD) simulations are used to identify interior airflow patterns, and then used these patterns to assess the building’s heat expulsion efficiency. Ambient temperatures of 20°C were adopted as the typical seasonal spring temperature range in Taipei. Further, “zero-wind” conditions are established to ensure simulation results reflected only the buoyancy effect. After checking results against neutral pressure level (NPL) level, airflow, air velocity, and indoor temperature stratification, the lower stack is modified to reduce the NPL in order to remove heat accumulated on the top floor.
Abstract: Haemodialysis (HD) is a procedure saving patient lives around the world, unfortunately it brings numerous complications. Oxidative stress is one of the major factors which lead to erythrocytes destruction during extracorporeal circulation. Repeated HD procedures destroy blood elements and the organism is not able to keep up with their production. 30 HD procedures on healthy sheep were performed to evaluate effects of such treatment. Oxidative stress study was performed together with an analysis of basic blood parameters and empirical assessment of dialyzer condition after the procedure. A reversible decline in absolute leukocyte count, during first 30 min of HD, was observed. Blood clots were formed in the area of the blood inlet and outlet of the dialyzer. Our results are consistent with outcomes presented throughout the literature specifically with respect to the effects observed in humans and will provide a basis to evaluate methods for blood protection during haemodialysis.
Abstract: Using Internet communication, new home electronics
have functions of monitoring and control from remote. However in
many case these electronics work as standalone, and old electronics
are not followed. Then, we developed the total remote system include
not only new electronics but olds. This systems node is a adapter of
electrical power plug that embed relay switch and some sensors, and
these nodes communicate with each other. the system server was build
on the Internet, and users access to this system from web browsers.
To reduce the cost to set up of this system, communication between
adapters are used ZigBee wireless network instead of wired LAN
cable[3]. From measured RSSI(received signal strength indicator)
information between each nodes, the system can estimate roughly
adapters were mounted on which room, and where in the room. So
also it reduces the cost of mapping nodes. Using this system, energy
saving and house monitoring are expected.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: in this paper we modified a simple two-dimensional
photonic crystal waveguide by creating micro cavity resonators in order to increase the output light emission which can be applicable to photonic integrated circuits. The micro cavity resonators are constructed by removing two tubes close to the waveguide output. Coupling emitted light from waveguide with those micro cavities, results increasing intensity of waveguide output light. Inserting a tube
in last row of waveguide, we have improved directionality of output
light beam.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: Tip vortex cavitation is one of well known patterns of
cavitation phenomenon which occurs in axial pumps. This pattern of
cavitation occurs due to pressure difference between the pressure and
suction sides of blades of an axial pump. Since the pressure in the
pressure side of the blade is higher than the pressure in its suction
side, thus a very small portion of liquid flow flows back from
pressure side to the suction side. This fact is cause of tip vortex
cavitation and gap cavitation that may occur in axial pumps. In this
paper the results of our experimental investigation about movement
of tip vortex cavitation along blade edge due to reduction of pump
flow rate in an axial pump is reported. Results show that reduction of
pump flow rate in conjunction with increasing of outlet pressure
causes movement of tip vortex cavitation along blade edge towards
the blade tip. Results also show that by approaching tip vortex
cavitation to the blade tip, vortex tip pattern of cavitation replaces
with a cavitation phenomenon on the blade tip. Furthermore by
further reduction of pump flow rate and increasing of outlet pressure,
an unstable cavitation phenomenon occurs between each blade
leading edge and the next blade trailing edge.
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: This work investigated the steady state and dynamic
simulation of a fixed bed industrial naphtha reforming reactors. The
performance of the reactor was investigated using a heterogeneous
model. For process simulation, the differential equations are solved
using the 4th order Runge-Kutta method .The models were validated
against measured process data of an existing naphtha reforming plant.
The results of simulation in terms of components yields and
temperature of the outlet were in good agreement with empirical data.
The simple model displays a useful tool for dynamic simulation,
optimization and control of naphtha reforming.
Abstract: The present study was performed in Musa bay (northern part of the Persian Gulf) around the coastal area of Bandare-Imam Khomeini and Razi Petrochemical Companies. Sediment samples and effluent samples were collected from the selected stations, from June 2009 to June 2010. The samples were analyzed to determine the degree of hydrocarbon contamination. The average level of TPH concentration in the study area was more than the natural background value at all of the stations, especially at station BI1 which was the main effluent outlet of Bandar-e- Imam Khomeini petrochemical company. Also the concentration of total petroleum hydrocarbon was monitored in the effluents of aforementioned petrochemical companies and the results showed that the concentration of TPH in the effluents of Bandar-e- Imam Khomeini petrochemical company was greater than Razi petrochemical company which is may be related to the products of Bandar-e- Imam Khomeini petrochemical company (aromatics, polymers, chemicals, fuel).