Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: β-Glucosidase is an important enzyme for production
of ethanol from lignocellulose. With hydrolytic activity on
cellooligosaccharides, especially cellobiose, β-glucosidase removes
product inhibitory effect on cellulases and forms fermentable sugars.
In this study, β-glucosidase encoding gene (BGL1) from traditional
starter yeast Saccharomycosis fibuligera BMQ908 was cloned and
expressed in Pichia pastoris. BGL1 of S. fibuligera BMQ 908 shared
98% nucleotide homology with the closest GenBank sequence
(M22475) but identity in amino-acid sequences of catalytic domains.
Recombinant plasmid pPICZαA/BGL1 containing the sequence
encoding BGL1 mature protein and α-factor secretion signal was
constructed and transformed into methylotrophic yeast P. pastoris by
electroporation. The recombinant strain produced single extracellular
protein with molecular weight of 120 kDa and cellobiase activity of
60 IU/ml. The optimum pH of the recombinant β-glucosidase was 5.0
and the optimum temperature was 50°C.
Abstract: Finding the minimal logical functions has important applications in the design of logical circuits. This task is solved by many different methods but, frequently, they are not suitable for a computer implementation. We briefly summarise the well-known Quine-McCluskey method, which gives a unique procedure of computing and thus can be simply implemented, but, even for simple examples, does not guarantee an optimal solution. Since the Petrick extension of the Quine-McCluskey method does not give a generally usable method for finding an optimum for logical functions with a high number of values, we focus on interpretation of the result of the Quine-McCluskey method and show that it represents a set covering problem that, unfortunately, is an NP-hard combinatorial problem. Therefore it must be solved by heuristic or approximation methods. We propose an approach based on genetic algorithms and show suitable parameter settings.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: In this paper, supply policy and procurement of
shared resources in some kinds of concurrent construction projects
are investigated. This could be oriented to the problems of holding
construction companies who involve in different projects
concurrently and they have to supply limited resources to several
projects as well as prevent delays to any project. Limits on
transportation vehicles and storage facilities for potential
construction materials and also the available resources (such as cash
or manpower) are some of the examples which affect considerably on
management of all projects over all. The research includes
investigation of some real multi-storey buildings during their
execution periods and surveying the history of the activities. It is
shown that the common resource demand variation curve of the
projects may be expanded or displaced to achieve an optimum
distribution scheme. Of course, it may cause some delay to some
projects, but it has minimum influence on whole execution period of
all projects and its influence on procurement cost of the projects is
considerable. These observations on investigation of some
multistorey building which are built in Iran will be presented in this
paper.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: In this paper, a novel associative memory model will be proposed and applied to memory retrievals based on the conventional continuous time model. The conventional model presents memory capacity is very low and retrieval process easily converges to an equilibrium state which is very different from the stored patterns. Genetic Algorithms is well-known with the capability of global optimal search escaping local optimum on progress to reach a global optimum. Based on the well-known idea of Genetic Algorithms, this work proposes a heuristic rule to make a mutation when the state of the network is trapped in a spurious memory. The proposal heuristic associative memory show the stored capacity does not depend on the number of stored patterns and the retrieval ability is up to ~ 1.
Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: The present study is aim to prepare and evaluate the selfnanoemulsifying drug delivery (SNEDDS) system of a poorly water soluble drug valsartan in order to achieve a better dissolution rate which would further help in enhancing oral bioavailability. The present research work describes a SNEDDS of valsartan using labrafil M 1944 CS, Tween 80 and Transcutol HP. The pseudoternary phase diagrams with presence and absence of drug were plotted to check for the emulsification range and also to evaluate the effect of valsartan on the emulsification behavior of the phases. The mixtures consisting of oil (labrafil M 1944 CS) with surfactant (tween 80), co-surfactant (Transcutol HP) were found to be optimum formulations. Prepared formulations were evaluated for its particle size distribution, nanoemulsifying properties, robustness to dilution, self emulsication time, turbidity measurement, drug content and invitro dissolution. The optimized formulations are further evaluated for heating cooling cycle, centrifugation studies, freeze thaw cycling, particle size distribution and zeta potential were carried out to confirm the stability of the formed SNEDDS formulations. The prepared formulation revealed t a significant improvement in terms of the drug solubility as compared with marketed tablet and pure drug.
Abstract: In this study, the precision heading process of
spur gears has been investigated by means of numerical
analysis. The effect of some parameters such as teeth number
and module on the forming force and material flow were
presented. The simulation works were performed rigid-plastic
finite element method using DEFORM 3D software. In order
to validate the estimated numerical results, they were
compared with those obtained experimentally during heading
of spur gear using lead as a model material. Results showed
that the optimum number of gear teeth is between 10 to 20,
that is because of being the specific pressure in its minimum
value.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: In this study, the possibility of using potato as a
substrate for glutamic acid production by Brevibacterium linens
was investigated. For preparation of fermentation medium, potato
was hydrolyzed by hydrochloridric acid. The medium contained
potato hydrolysate, tween 80, mineral solution, glucose, and
potassium hydrogen phosphate. The initial pH of the medium was
adjusted to 7-7.5. For achieving the optimum time with maximum
yield, the beakers containing the medium and the inoculums were
incubated in a rotary water bath flask shaker for one to five days.
Thin layer choromatography was used for quantitative and
qualitative assay of the glutamic acid produced. The results
revealed that as fermentation time increased, pH of the
fermentation medium significantly decreased (P
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of cassava (Manihot esculenta)
starch powder (of mesh 80/120) into glucose syrup by immobilized
(using Polyacrylamide gel) a-amylase using central composite
design. The experimental result on enzymatic hydrolysis of cassava
starch was subjected to multiple linear regression analysis using
MINITAB 14 software. Positive linear effect of starch concentration,
enzyme concentration and time was observed on hydrolysis of
cassava starch by a-amylase. The statistical significance of the model
was validated by F-test for analysis of variance (p < 0.01). The
optimum value of starch concentration temperature, time and enzyme
concentration were found to be 4.5% (w/v), 45oC, 150 min, and 1%
(w/v) enzyme. The maximum glucose yield at optimum condition
was 5.17 mg/mL.
Abstract: Several valve stiction models have been proposed in the literature to help understand and study the behavior of sticky valves. In this paper, an alternative black-box modeling approach based on Neural Network (NN) is presented. It is shown that with proper network type and optimum model structures, the performance of the developed NN stiction model is comparable to other established method. The resulting NN model is also tested for its robustness against the uncertainty in the stiction parameter values. Predictive mode operation also shows excellent performance of the proposed model for multi-steps ahead prediction.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: This paper presents a boarding on biometric
authentication through the Keystrokes Dynamics that it intends to
identify a person from its habitual rhythm to type in conventional
keyboard. Seven done experiments: verifying amount of prototypes,
threshold, features and the variation of the choice of the times of the
features vector. The results show that the use of the Keystroke
Dynamics is simple and efficient for personal authentication, getting
optimum resulted using 90% of the features with 4.44% FRR and 0%
FAR.
Abstract: The objective of this research is to study the technical
and economic performance of wind/diesel/battery (W/D/B) system
supplying a remote small gathering of six families using HOMER
software package. The electrical energy is to cater for the basic needs
for which the daily load pattern is estimated. Net Present Cost (NPC)
and Cost of Energy (COE) are used as economic criteria, while the measure of performance is % of power shortage. Technical and
economic parameters are defined to estimate the feasibility of the
system under study. Optimum system configurations are estimated for two sites. Using HOMER software, the simulation results showed that W/D/B systems are economical for the assumed community sites
as the price of generated electricity is about 0.308 $/kWh, without
taking external benefits into considerations. W/D/B systems are more
economical than W/B or diesel alone systems, as the COE is 0.86 $/kWh for W/B and 0.357 $/kWh for diesel alone.
Abstract: In this study the adsorption of Cu (II) ions from aqueous solutions on synthetic zeolite NaA was evaluated. The effect of solution temperature and the determination of the kinetic parameters of adsorption of Cu(II) from aqueous solution on zeolite NaA is important in understanding the adsorption mechanism. Variables of the system include adsorption time, temperature (293- 328K), initial solution concentration and pH for the system. The sorption kinetics of the copper ions were found to be strongly dependent on pH (the optimum pH 3-5), solute ion concentration and temperature (293 – 328 K). It was found, the pseudo-second-order model was the best choice among all the kinetic models to describe the adsorption behavior of Cu(II) onto ziolite NaA, suggesting that the adsorption mechanism might be a chemisorptions process The activation energy of adsorption (Ea) was determined as Cu(II) 13.5 kJ mol-1. The low value of Ea shows that Cu(II) adsorption process by zeolite NaA may be an activated chemical adsorption. The thermodynamic parameters (ΔG0, ΔH0, and ΔS0) were also determined from the temperature dependence. The results show that the process of adsorption Cu(II) is spontaneous and endothermic process and rise in temperature favors the adsorption.