Abstract: The linear stability of nanofluid convection in a horizontal porous layer is examined theoretically when the walls of the porous layer are subjected to time-periodic temperature modulation. The model used for the nanofluid incorporates the effects of Brownian motion and thermopherosis, while the Darcy model is used for the porous medium. The analysis revels that for a typical nanofluid (with large Lewis number) the prime effect of the nanofluids is via a buoyancy effect coupled with the conservation of nanoparticles. The contribution of nanoparticles to the thermal energy equation being a second-order effect. It is found that the critical thermal Rayleigh number can be found reduced or decreased by a substantial amount, depending on whether the basic nanoparticle distribution is top-heavy or bottom-heavy. Oscillatory instability is possible in the case of a bottom-heavy nanoparticle distribution, phase angle and frequency of modulation.
Abstract: Heat transfer behavior of three different types of nanofluids flowing through a horizontal tube under laminar regime has been investigated numerically. The wall of tube is maintained at constant temperature. Al2O3-water, CuO-water and TiO2-water are used with different Reynolds number and different volume fraction. The numerical results of heat transfer indicate that the Nusselt number of nanofluids is larger than that of the base fluid. The Pressure loss coefficient decreases by increasing Reynolds number for all types of nanofluids. Results of Nusselt number enhancement and pressure loss coefficient enhancement indicate that Al2O3 nanoparticules give the best results in term of thermal-hydrolic properties.
Abstract: The present work is a numerical simulation of
nanofluids flow in a double pipe heat exchanger provided with
porous baffles. The hot nanofluid flows in the inner cylinder, whereas
the cold nanofluid circulates in the annular gap. The Darcy-
Brinkman-Forchheimer model is adopted to describe the flow in the
porous regions, and the governing equations with the appropriate
boundary conditions are solved by the finite volume method. The
results reveal that the addition of metallic nanoparticles enhances the
rate of heat transfer in comparison to conventional fluids but this
augmentation is accompanied by an increase in pressure drop. The
highest heat exchanger performances are obtained when
nanoparticles are added only to the cold fluid.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: Magnetic carbon nanotubes composites were obtained
by filling carbon nanotubes with paramagnetic iron oxide particles.
Detailed investigation of magnetic behaviour of resulting composites
was done at different temperatures. Measurements indicate that these
functionalized nanotubes are superparamagnetic at room temperature;
however, no superparamagnetism was observed at 125 K and 80 K.
The blocking temperature TB was estimated at 145 K. These magnetic
carbon nanotubes have the potential of being used in a wide range of
applications, in particular, the production of nanofluids, which can be
controlled and steered by appropriate magnetic fields.
Abstract: Buoyancy driven heat transfer of nanofluids in a
cylindrical enclosure used as a control unit in the subsea hydrocarbon
injection wells is investigated in this study. The governing equations
obtained with the Boussinesq approximation are solved using Comsol
Multiphysics finite element analysis and simulation software. The
base fluid is water and CuO is used as nanoparticles. Solution is
obtained for nanoparticle solid volume fraction of 8% and for
Rayleigh number in the range of 105-107. The results show that
nanoparticle usage in the cylindrical electronic control unit has a
significant effect on the flow and heat transfer.
Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Nanofluids are novel fluids that are going to have an
important role in future industrial thermal device designs. Studies are
being predominantly conducted on the mechanism of these heat
transfers. The key to this attraction is in the increase in thermal
conductivity brought about by the Nanofluids compared with the
base fluid. Different models have been proposed for calculation of
effective thermal conduction that has been gradually modified. In this
investigation effect of nanolayer structure and Brownian motion of
particles are studied and a new modified thermal conductivity model
is proposed. Temperature, concentration, nanolayer thickness and
particle size are taken as variables and their effect are studied
simultaneously on the thermal conductivity of the fluids, showing the
concentration of the nanoparticles to affect the nanolayer thickness
which also affects the Brownian motion.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: This paper presents a linear stability analysis of
natural convection in a horizontal layer of a viscoelastic
nanofluid. The Oldroyd B model was utilized to describe the
rheological behavior of a viscoelastic nanofluid. The model
used for the nanofluid incorporated the effects of Brownian
motion and thermophoresis. The onset criterion for stationary
and oscillatory convection was derived analytically. The effects
of the Deborah number, retardation parameters, concentration
Rayleigh number, Prandtl number, and Lewis number on the
stability of the system were investigated. Results indicated that
there was competition among the processes of thermophoresis,
Brownian diffusion, and viscoelasticity which caused
oscillatory rather than stationary convection to occur.
Oscillatory instability is possible with both bottom- and
top-heavy nanoparticle distributions. Regimes of stationary and
oscillatory convection for various parameters were derived and
are discussed in detail.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: Novel Coconut oil nanofluids of various concentrations have been prepared through ultrasonically assisted sol-gel method. The structural and morphological properties of the copper oxide nanoparticle have been analyzed with respectively and it revealed the monoclinic end-centered structure of crystallite and shuttle like flake morphology of agglomerates. Ultrasonic studies have been made for the nanofluids at different temperatures. The molecular interactions responsible for the changes in acoustical parameter with respect to concentration and temperature are discussed.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.