Abstract: To improve the dynamics response of the vehicle
passive suspension, a two-terminal mass is suggested to connect in
parallel with the suspension strut. Three performance criteria, tire grip,
ride comfort and suspension deflection, are taken into consideration to
optimize the suspension parameters. However, the three criteria are
conflicting and non-commensurable. For this reason, the Chebyshev
goal programming method is applied to find the best tradeoff among
the three objectives. A simulation case is presented to describe the
multi-objective optimization procedure. For comparison, the
Chebyshev method is also employed to optimize the design of a
conventional passive suspension. The effectiveness of the proposed
design method has been clearly demonstrated by the result. It is also
shown that the suspension with a two-terminal mass in parallel has
better performance in terms of the three objectives.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.
Abstract: In the last decades to supply the various and different
demands of clients, a lot of manufacturers trend to use the mixedmodel
assembly line (MMAL) in their production lines, since this
policy make possible to assemble various and different models of the
equivalent goods on the same line with the MTO approach.
In this article, we determine the sequence of (MMAL) line, with
applying the kitting approach and planning of rest time for general
workers to reduce the wastages, increase the workers effectiveness
and apply the sector of lean production approach.
This Multi-objective sequencing problem solved in small size with
GAMS22.2 and PSO meta heuristic in 10 test problems and compare
their results together and conclude that their results are very similar
together, next we determine the important factors in computing the
cost, which improving them cost reduced. Since this problem, is NPhard
in large size, we use the particle swarm optimization (PSO)
meta-heuristic for solving it. In large size we define some test
problems to survey it-s performance and determine the important
factors in calculating the cost, that by change or improved them
production in minimum cost will be possible.
Abstract: This paper presents a multi-objective order allocation
planning problem with the consideration of various real-world
production features. A novel hybrid intelligent optimization model,
integrating a multi-objective memetic optimization process, a Monte
Carlo simulation technique and a heuristic pruning technique, is
proposed to handle this problem. Experiments based on industrial data
are conducted to validate the proposed model. Results show that (1)
the proposed model can effectively solve the investigated problem by
providing effective production decision-making solutions, which
outperformsan NSGA-II-based optimization process and an industrial
method.
Abstract: The unanticipated brittle fracture of connection of the
steel moment resisting frame (SMRF) occurred in 1994 the Northridge
earthquake. Since then, the researches for the vulnerability of
connection of the existing SMRF and for rehabilitation of those
buildings were conducted. This paper suggests performance-based
optimal seismic retrofit technique using connection upgrade. For
optimal design, a multi-objective genetic algorithm(NSGA-II) is used.
One of the two objective functions is to minimize initial cost and
another objective function is to minimize lifetime seismic damages
cost. The optimal algorithm proposed in this paper is performed
satisfying specified performance objective based on FEMA 356. The
nonlinear static analysis is performed for structural seismic
performance evaluation. A numerical example of SAC benchmark
SMRF is provided using the performance-based optimal seismic
retrofit technique proposed in this paper
Abstract: This work presents a multiple objective linear programming (MOLP) model based on the desirability function approach for solving the aggregate production planning (APP) decision problem upon Masud and Hwang-s model. The proposed model minimises total production costs, carrying or backordering costs and rates of change in labor levels. An industrial case demonstrates the feasibility of applying the proposed model to the APP problems with three scenarios of inventory levels. The proposed model yields an efficient compromise solution and the overall levels of DM satisfaction with the multiple combined response levels. There has been a trend to solve complex planning problems using various metaheuristics. Therefore, in this paper, the multi-objective APP problem is solved by hybrid metaheuristics of the hunting search (HuSIHSA) and firefly (FAIHSA) mechanisms on the improved harmony search algorithm. Results obtained from the solution of are then compared. It is observed that the FAIHSA can be used as a successful alternative solution mechanism for solving APP problems over three scenarios. Furthermore, the FAIHSA provides a systematic framework for facilitating the decision-making process, enabling a decision maker interactively to modify the desirability function approach and related model parameters until a good optimal solution is obtained with proper selection of control parameters when compared.
Abstract: In rapidly changing market environment, firms are investing a lot of time and resources into new product development (NPD) projects to make profit and to obtain competitive advantage. However, failure rate of NPD projects is becoming high due to various internal and external risks which hinder successful NPD projects. To reduce the failure rate, it is critical that risks have to be managed effectively and efficiently through good strategy, and treated by optimal responses to minimize risk cost. Four strategies are adopted to handle the risks in this study. The optimal responses are characterized by high reduction of risk costs with high efficiency. This study suggests a framework to decide the optimal responses considering the core risks, risk costs, response efficiency and response costs for successful NPD projects. Both binary particles warm optimization (BPSO) and multi-objective particle swarm optimization (MOPSO) methods are mainly used in the framework. Although several limitations exist in use for real industries, the frame work shows good strength for handling the risks with highly scientific ways through an example.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Development of motor car safety devices has reduced
fatality rates in car accidents. Yet despite this increase in car safety,
neck injuries resulting from rear impact collisions, particularly at low
speed, remain a primary concern. In this study, FEA(Finite Element
Analysis) of seat was performed to evaluate neck injuries in rear
impact. And the FEA result was verified by comparison with the actual
test results. The dummy used in FE model and actual test is BioRID II
which is regarded suitable for rear impact collision analysis. A
threshold of the BioRID II neck injury indicators was also proposed to
upgrade seat performance in order to reduce whiplash injury. To
optimize the seat for a low-speed rear impact collision, a method was
proposed, which is multi-objective optimization idea using DOE
(Design of Experiments) results.
Abstract: Project managers are the ultimate responsible for the
overall characteristics of a project, i.e. they should deliver the project
on time with minimum cost and with maximum quality. It is vital for
any manager to decide a trade-off between these conflicting
objectives and they will be benefited of any scientific decision
support tool. Our work will try to determine optimal solutions (rather
than a single optimal solution) from which the project manager will
select his desirable choice to run the project. In this paper, the
problem in project scheduling notated as
(1,T|cpm,disc,mu|curve:quality,time,cost) will be studied. The
problem is multi-objective and the purpose is finding the Pareto
optimal front of time, cost and quality of a project
(curve:quality,time,cost), whose activities belong to a start to finish
activity relationship network (cpm) and they can be done in different
possible modes (mu) which are non-continuous or discrete (disc), and
each mode has a different cost, time and quality . The project is
constrained to a non-renewable resource i.e. money (1,T). Because
the problem is NP-Hard, to solve the problem, a meta-heuristic is
developed based on a version of genetic algorithm specially adapted
to solve multi-objective problems namely FastPGA. A sample project
with 30 activities is generated and then solved by the proposed
method.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: Environmental awareness and the recent
environmental policies have forced many electric utilities to
restructure their operational practices to account for their emission
impacts. One way to accomplish this is by reformulating the
traditional economic dispatch problem such that emission effects are
included in the mathematical model. This paper presents a Particle
Swarm Optimization (PSO) algorithm to solve the Economic-
Emission Dispatch problem (EED) which gained recent attention due
to the deregulation of the power industry and strict environmental
regulations. The problem is formulated as a multi-objective one with
two competing functions, namely economic cost and emission
functions, subject to different constraints. The inequality constraints
considered are the generating unit capacity limits while the equality
constraint is generation-demand balance. A novel equality constraint
handling mechanism is proposed in this paper. PSO algorithm is
tested on a 30-bus standard test system. Results obtained show that
PSO algorithm has a great potential in handling multi-objective
optimization problems and is capable of capturing Pareto optimal
solution set under different loading conditions.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.
Abstract: Environmental pollution problems have been globally
main concern in all fields including economy, society and culture into
the 21st century. Beginning with the Kyoto Protocol, the reduction on
the emissions of greenhouse gas such as CO2 and SOX has been a
principal challenge of our day. As most buildings unlike durable goods
in other industries have a characteristic and long life cycle, they
consume energy in quantity and emit much CO2. Thus, for green
building construction, more research is needed to reduce the CO2
emissions at each stage in the life cycle. However, recent studies are
focused on the use and maintenance phase. Also, there is a lack of
research on the initial design stage, especially the structure design.
Therefore, in this study, we propose an optimal design plan
considering CO2 emissions and cost in composite buildings
simultaneously by applying to the structural design of actual building.
Abstract: Nowadays, the challenge in hydraulic turbine design is
the multi-objective design of turbine runner to reach higher
efficiency. The hydraulic performance of a turbine is strictly depends
on runner blades shape. The present paper focuses on the application
of the multi-objective optimization algorithm to the design of a small
Francis turbine runner. The optimization exercise focuses on the
efficiency improvement at the best efficiency operating point (BEP)
of the GAMM Francis turbine. A global optimization method based
on artificial neural networks (ANN) and genetic algorithms (GA)
coupled by 3D Navier-Stokes flow solver has been used to improve
the performance of an initial geometry of a Francis runner. The
results show the good ability of optimization algorithm and the final
geometry has better efficiency with initial geometry. The goal was to
optimize the geometry of the blades of GAMM turbine runner which
leads to maximum total efficiency by changing the design parameters
of camber line in at least 5 sections of a blade. The efficiency of the
optimized geometry is improved from 90.7% to 92.5%. Finally,
design parameters and the way of selection have been considered and
discussed.
Abstract: In some real applications of Statistical Process Control
it is necessary to design a control chart to not detect small process
shifts, but keeping a good performance to detect moderate and large
shifts in the quality. In this work we develop a new quality control
chart, the synthetic T2 control chart, that can be designed to cope with
this objective. A multi-objective optimization is carried out employing
Genetic Algorithms, finding the Pareto-optimal front of
non-dominated solutions for this optimization problem.
Abstract: The Prediction of aerodynamic characteristics and
shape optimization of airfoil under the ground effect have been carried
out by integration of computational fluid dynamics and the multiobjective
Pareto-based genetic algorithm. The main flow
characteristics around an airfoil of WIG craft are lift force, lift-to-drag
ratio and static height stability (H.S). However, they show a strong
trade-off phenomenon so that it is not easy to satisfy the design
requirements simultaneously. This difficulty can be resolved by the
optimal design. The above mentioned three characteristics are chosen
as the objective functions and NACA0015 airfoil is considered as a
baseline model in the present study. The profile of airfoil is
constructed by Bezier curves with fourteen control points and these
control points are adopted as the design variables. For multi-objective
optimization problems, the optimal solutions are not unique but a set
of non-dominated optima and they are called Pareto frontiers or Pareto
sets. As the results of optimization, forty numbers of non- dominated
Pareto optima can be obtained at thirty evolutions.
Abstract: With the increasing complexity of engineering
problems, the traditional, single-objective and deterministic
optimization method can not meet people-s requirements. A
multi-objective fuzzy optimization model of resource input is built for
M chlor-alkali chemical eco-industrial park in this paper. First, the
model is changed into the form that can be solved by genetic algorithm
using fuzzy theory. And then, a fitness function is constructed for
genetic algorithm. Finally, a numerical example is presented to show
that the method compared with traditional single-objective
optimization method is more practical and efficient.
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.