Abstract: It is very well known that certain vertical and longitudinal slopes have to be assured in order to achieve adequate rainwater runoff from the pavement. The selection of longitudinal slopes, between the turning points of the vertical curves that meet the afore-mentioned requirement does not ensure adequate drainage because the same condition must also be applied at the transition curves. In this way none of the pavement edges’ slopes (as well as any other spot that lie on the pavement) will be opposite to the longitudinal slope of the rotation axis. Horizontal and vertical alignment must be properly combined in order to form a road which resultant slope does not take small values and hence, checks must be performed in every cross section and every chainage of the road. The present research investigates the rain water runoff from the road surface in order to identify the conditions under which, areas of inadequate drainage are being created, to analyze the rainwater behavior in such areas, to provide design examples of good and bad drainage zones and to track down certain motorcycle types which might encounter hazardous situations due to the presence of water film between the pavement and both of their tires resulting loss of traction. Moreover, it investigates the combination of longitudinal and cross slope values in critical pavement areas. It should be pointed out that the drainage gradient is analytically calculated for the whole road width and not just for an oblique slope per chainage (combination of longitudinal grade and cross slope). Lastly, various combinations of horizontal and vertical design are presented, indicating the crucial zones of bad pavement drainage. The key conclusion of the study is that any type of motorcycle will travel for some time inside the area of improper runoff for a certain time frame which depends on the speed and the trajectory that the rider chooses along the transition curve. Taking into account that on this section the rider will have to lean his motorcycle and hence reduce the contact area of his tire with the pavement it is apparent that any variations on the friction value due to the presence of a water film may lead to serious problems regarding his safety. The water runoff from the road pavement is improved when between reverse longitudinal slopes, crest instead of sag curve is chosen and particularly when its edges coincide with the edges of the horizontal curve. Lastly, the results of the investigation have shown that the variation of the longitudinal slope involves the vertical shift of the center of the poor water runoff area. The magnitude of this area increases as the length of the transition curve increases.
Abstract: Telescopic Front Fork (TFF) used in two wheelers, mainly motorcycle, is made from high strength steel, and is manufactured by high frequency induction welding process wherein hot rolled and pickled coils are used as input raw material for rolling of hollow tubes followed by heat treatment, surface treatment, cold drawing, tempering, etc. The final application demands superior quality TFF tubes w.r.t. surface finish and dimensional tolerances. This paper presents the investigation of two different types of failure of fork during operation. The investigation consists of visual inspection, chemical analysis, characterization of microstructure, and energy dispersive spectroscopy. In this paper, comprehensive investigations of two failed tube samples were investigated. In case of Sample #1, the result revealed that there was a pre-existing crack, known as hook crack, which leads to the cracking of the tube. Metallographic examination exhibited that during field operation the pre-existing hook crack was surfaced out leading to crack in the pipe. In case of Sample #2, presence of internal oxidation with decarburised grains inside the material indicates origin of the defect from slab stage.
Abstract: The motorcycle has become one of the most common type of vehicles used on the road, particularly in the Asia region, including Malaysia, due to its size-convenience and affordable price. This study focuses only on crashes involving motorcycles with passenger cars consisting 43 real world crashes obtained from in-depth crash investigation process from June 2016 till July 2017. The study collected and analyzed vehicle and site parameters obtained during crash investigation and injury information acquired from the patient-treating hospital. The investigation team, consisting of two personnel, is stationed at the Emergency Department of the treatment facility, and was dispatched to the crash scene once receiving notification of the related crashes. The injury information retrieved was coded according to the level of severity using the Abbreviated Injury Scale (AIS) and classified into different body regions. The data revealed that weekend crashes were significantly higher for the night time period and the crash occurrence was the highest during morning hours (commuting to work period) for weekdays. Bad weather conditions play a minimal effect towards the occurrence of motorcycle – passenger vehicle crashes and nearly 90% involved motorcycles with single riders. Riders up to 25 years old are heavily involved in crashes with passenger vehicles (60%), followed by 26-55 year age group with 35%. Male riders were dominant in each of the age segments. The majority of the crashes involved side impacts, followed by rear impacts and cars outnumbered the rest of the passenger vehicle types in terms of crash involvement with motorcycles. The investigation data also revealed that passenger vehicles were the most at-fault counterpart (62%) when involved in crashes with motorcycles and most of the crashes involved situations whereby both of the vehicles are travelling in the same direction and one of the vehicles is in a turning maneuver. More than 80% of the involved motorcycle riders had sustained yellow severity level during triage process. The study also found that nearly 30% of the riders sustained injuries to the lower extremities, while MAIS level 3 injuries were recorded for all body regions except for thorax region. The result showed that crashes in which the motorcycles were found to be at fault were more likely to occur during night and raining conditions. These types of crashes were also found to be more likely to involve other types of passenger vehicles rather than cars and possess higher likelihood in resulting higher ISS (>6) value to the involved rider. To reduce motorcycle fatalities, it first has to understand the characteristics concerned and focus may be given on crashes involving passenger vehicles as the most dominant crash partner on Malaysian roads.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: The national economy development affects the vehicle
ownership which ultimately increases fuel consumption. The rise of
the vehicle ownership is dominated by the increasing number of
motorcycles. This research aims to analyze and identify the
characteristics of fuel consumption, the city transportation system,
and to analyze the relationship and the effect of the city
transportation system on the fuel consumption. A multivariable
analysis is used in this study. The data analysis techniques include: a
Multivariate Multivariable Analysis by using the R software. More
than 84% of fuel on Java is consumed in metropolitan and large
cities. The city transportation system variables that strongly effect the
fuel consumption are population, public vehicles, private vehicles and
private bus. This method can be developed to control the fuel
consumption by considering the urban transport system and city
tipology. The effect can reducing subsidy on the fuel consumption,
increasing state economic.
Abstract: Although electrical motors are still the main devices
used in vehicular exhaust comprises more than 95 percent of the air
pollution in Taiwan's largest city, Taipei. On average, all commuters in Taipei travel 13.6 km daily, while motorcycle commuters travel 12.2 km. The convenience and mobility of motorcycles makes them
irreplaceable in Taiwan city traffic but they add significantly to air pollution problems. In order to improve air pollution conditions, some
new types of vehicles have been proposed, such as fuel cell driven and
hybrid energy vehicles. In this study, we develop a model pneumatic hybrid motorcycle system and simulate its acceleration and mileage
(km/L) performance. The results show that the pneumatic hybrid
motorcycle can improve efficiency.
Abstract: Increasing number of vehicles and lack of awareness among road users may lead to road accidents. However no specific literature was found to rank vehicles involved in accidents based on fuzzy variables of road users. This paper proposes a ranking of four selected motor vehicles involved in road accidents. Human and non-human factors that normally linked with road accidents are considered for ranking. The imprecision or vagueness inherent in the subjective assessment of the experts has led the application of fuzzy sets theory to deal with ranking problems. Data in form of linguistic variables were collected from three authorised personnel of three Malaysian Government agencies. The Multi Criteria Decision Making, fuzzy TOPSIS was applied in computational procedures. From the analysis, it shows that motorcycles vehicles yielded the highest closeness coefficient at 0.6225. A ranking can be drawn using the magnitude of closeness coefficient. It was indicated that the motorcycles recorded the first rank.
Abstract: This paper present the study carried out of accident
analysis, black spot study and to develop accident predictive models
based on the data collected at rural roadway, Federal Route 50 (F050)
Malaysia. The road accident trends and black spot ranking were
established on the F050. The development of the accident prediction
model will concentrate in Parit Raja area from KM 19 to KM 23.
Multiple non-linear regression method was used to relate the discrete
accident data with the road and traffic flow explanatory variable. The
dependent variable was modeled as the number of crashes namely
accident point weighting, however accident point weighting have
rarely been account in the road accident prediction Models. The result
show that, the existing number of major access points, without traffic
light, rise in speed, increasing number of Annual Average Daily
Traffic (AADT), growing number of motorcycle and motorcar and
reducing the time gap are the potential contributors of increment
accident rates on multiple rural roadway.
Abstract: Based on statistics released by Islamic Republic of
Iran Police (IRIP), from among the total 9555 motorcycle accidents
that happened in 2007, 857 riders died and 11219 one got injured. If
we also consider the death toll and injuries of other vehicles'
accidents resulted from traffic violation by motorcycle riders, then
paying attention to the motorcycle accidents seems to be very
necessary. Therefore, in this study we tried to investigate the traits
and issues related to production, application, and training, along with
causes of motorcycle accidents from 4 perspectives of road, human,
environment and vehicle and also based on statistical and
geographical analysis of accident-sheets prepared by Iran Road
Patrol Department (IRPD). Unfamiliarity of riders with regulations
and techniques of motorcycling, disuse of safety equipments,
inefficiency of roads and design of junctions for safe trafficking of
motorcycles and finally the lack of sufficient control of responsible
organizations are among the major causes which lead to these
accidents.
Abstract: This research is designed for helping a WAPbased mobile phone-s user in order to analyze of logistics in the traffic area by applying and designing the accessible processes from mobile user to server databases. The research-s design comprises Mysql 4.1.8-nt database system for being the server which there are three sub-databases, traffic light – times of intersections in periods of the day, distances on the road of area-blocks where are divided from the main sample-area and speeds of sample vehicles (motorcycle, personal car and truck) in periods of the day. For interconnections between the server and user, PHP is used to calculate distances and travelling times from the beginning point to destination, meanwhile XHTML applied for receiving, sending and displaying data from PHP to user-s mobile. In this research, the main sample-area is focused at the Huakwang-Ratchada-s area, Bangkok, Thailand where usually the congested point and 6.25 km2 surrounding area which are split into 25 blocks, 0.25 km2 for each. For simulating the results, the designed server-database and all communicating models of this research have been uploaded to www.utccengineering.com/m4tg and used the mobile phone which supports WAP 2.0 XHTML/HTML multimode browser for observing values and displayed pictures. According to simulated results, user can check the route-s pictures from the requiring point to destination along with analyzed consuming times when sample vehicles travel in various periods of the day.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Identifying and classifying intersections according to
severity is very important for implementation of safety related
counter measures and effective models are needed to compare and
assess the severity. Highway safety organizations have considered
intersection safety among their priorities. In spite of significant
advances in highways safety, the large numbers of crashes with high
severities still occur in the highways. Investigation of influential
factors on crashes enables engineers to carry out calculations in order
to reduce crash severity. Previous studies lacked a model capable of
simultaneous illustration of the influence of human factors, road,
vehicle, weather conditions and traffic features including traffic
volume and flow speed on the crash severity. Thus, this paper is
aimed at developing the models to illustrate the simultaneous
influence of these variables on the crash severity in urban highways.
The models represented in this study have been developed using
binary Logit Models. SPSS software has been used to calibrate the
models. It must be mentioned that backward regression method in
SPSS was used to identify the significant variables in the model.
Consider to obtained results it can be concluded that the main
factor in increasing of crash severity in urban highways are driver
age, movement with reverse gear, technical defect of the vehicle,
vehicle collision with motorcycle and bicycle, bridge, frontal impact
collisions, frontal-lateral collisions and multi-vehicle crashes in
urban highways which always increase the crash severity in urban
highways.
Abstract: The culture of riding heavy motorcycles originates
from advanced countries and mainly comes from Europe, North
America, and Japan. Heavy duty motorcycle riders are different from
people who view motorcycles as a convenient mean of transportation.
They regard riding them as a kind of enjoyment and high-level taste.
The activities of riding heavy duty motorcycles have formes a
distinctive landscape in domestic land in Taiwan. Previous studies
which explored motorcycle culture in Taiwan still focused on the
objects of motorcycle engine displacement under 50 cc.. The study
aims to study the heavy duty motorcycles of engine displacement over
550 cc. and explores where their attractiveness is. For finding the
attractiveness of heavy duty motorcycle, the study chooses Miryoku
Engineering (Preference-Based Design) approach. Two steps are
adopted to proceed the research. First, through arranging the letters
obtained from interviewing experts, EGM (The Evaluation Grid
Method) was applied to find out the structure of attractiveness. The
attractive styles are eye-dazzling, leisure, classic, and racing
competitive styles. Secondarily, Quantification Theory Type I analysis
was adopted as a tool for analyzing the importance of attractiveness.
The relationship between style and attractive parts was also discussed.
The results could contribute to the design and research development of
heavy duty motorcycle industry in Taiwan.
Abstract: With the increase of economic behavior and the upgrade
of living standar, the ratio for people in Taiwan who own automobiles
and motorcycles have recently increased with multiples. Therefore,
parking issues will be a big challenge to facilitate traffic network and
ensure urban life quality. The Parking Guidance and Information
System is one of important systems for Advanced Traveler Information
Services (ATIS). This research proposes a parking guidance and
information system which integrates GPS and 3G network for a map on
the Geographic Information System to solution inadequate of roadside
information kanban. The system proposed in this study mainly includes
Parking Host, Parking Guidance and Information Server, Geographic
Map and Information System as well as Parking Guidance and
Information Browser. The study results show this system can increase
driver-s efficiency to find parking space and efficiently enhance
parking convenience in comparison with roadside kanban system.