Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: This paper presents a study of the Taguchi design
application to optimize surface quality in damper inserted end milling
operation. Maintaining good surface quality usually involves
additional manufacturing cost or loss of productivity. The Taguchi
design is an efficient and effective experimental method in which a
response variable can be optimized, given various factors, using
fewer resources than a factorial design. This Study included spindle
speed, feed rate, and depth of cut as control factors, usage of different
tools in the same specification, which introduced tool condition and
dimensional variability. An orthogonal array of L9(3^4)was used;
ANOVA analyses were carried out to identify the significant factors
affecting surface roughness, and the optimal cutting combination was
determined by seeking the best surface roughness (response) and
signal-to-noise ratio. Finally, confirmation tests verified that the
Taguchi design was successful in optimizing milling parameters for
surface roughness.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.
Abstract: The changing economic climate has made global
manufacturing a growing reality over the last decade, forcing
companies from east and west and all over the world to
collaborate beyond geographic boundaries in the design,
manufacture and assemble of products. The ISO10303 and
ISO14649 Standards (STEP and STEP-NC) have been
developed to introduce interoperability into manufacturing
enterprises so as to meet the challenge of responding to
production on demand. This paper describes and illustrates a
STEP compliant CAD/CAPP/CAM System for the manufacture
of rotational parts on CNC turning centers. The information
models to support the proposed system together with the data
models defined in the ISO14649 standard used to create the NC
programs are also described. A structured view of a STEP
compliant CAD/CAPP/CAM system framework supporting the
next generation of intelligent CNC controllers for turn/mill
component manufacture is provided. Finally a proposed
computational environment for a STEP-NC compliant system
for turning operations (SCSTO) is described. SCSTO is the
experimental part of the research supported by the specification
of information models and constructed using a structured
methodology and object-oriented methods. SCSTO was
developed to generate a Part 21 file based on machining
features to support the interactive generation of process plans
utilizing feature extraction. A case study component has been
developed to prove the concept for using the milling and turning
parts of ISO14649 to provide a turn-mill CAD/CAPP/CAM
environment.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: One of the main concerns about parallel mechanisms
is the presence of singular points within their workspaces. In singular
positions the mechanism gains or loses one or several degrees of
freedom. It is impossible to control the mechanism in singular
positions. Therefore, these positions have to be avoided. This is a
vital need especially in computer controlled machine tools designed
and manufactured on the basis of parallel mechanisms. This need has
to be taken into consideration when selecting design parameters. A
prerequisite to this is a thorough knowledge about the effect of
design parameters and constraints on singularity. In this paper,
quality condition index was introduced as a criterion for evaluating
singularities of different configurations of a hexapod mechanism
obtainable by different design parameters. It was illustrated that this
method can effectively be employed to obtain the optimum
configuration of hexapod mechanism with the aim of avoiding
singularity within the workspace. This method was then employed to
design the hexapod table of a CNC milling machine.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: The objective of this research was to study factors,
which were affected on surface roughness in high speed milling of
hardened tool steel. Material used in the experiment was tool steel JIS
SKD 61 that hardened on 60 ±2 HRC. Full factorial experimental
design was conducted on 3 factors and 3 levels (3
3
designs) with 2
replications. Factors were consisted of cutting speed, feed rate, and
depth of cut. The results showed that influenced factor affected to
surface roughness was cutting speed, feed rate and depth of cut which
showed statistical significant. Higher cutting speed would cause on
better surface quality. On the other hand, higher feed rate would cause
on poorer surface quality. Interaction of factor was found that cutting
speed and depth of cut were significantly to surface quality. The
interaction of high cutting speed associated with low depth of cut
affected to better surface quality than low cutting speed and high depth
of cut.
Abstract: To understand complex living system an effort has
made by mechanical engineers and dentists to deliver prompt
products and services to patients concerned about their aesthetic look.
Since two decades various bracket systems have designed involving
techniques like milling, injection molding which are technically not
flexible for the customized dental product development. The aim of
this paper to design, develop a customized system which is
economical and mainly emphasizes the expertise design and
integration of engineering and dental fields. A custom made selfadjustable
lingual bracket and customized implants are designed and
developed using computer aided design (CAD) and rapid prototyping
technology (RPT) to improve the smiles and to overcome the
difficulties associated with conventional ones. Lengthy orthodontic
treatment usually not accepted by the patients because the patient
compliance is lost. Patient-s compliance can be improved by
facilitating faster tooth movements by designing a localized dental
vibrator using advanced engineering principles.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: This paper proposes a method to vibration analysis in
order to on-line monitoring and predictive maintenance during the
milling process. Adapting envelope method to diagnostics and the
analysis for milling tool materials is an important contribution to the
qualitative and quantitative characterization of milling capacity and a
step by modeling the three-dimensional cutting process. An
experimental protocol was designed and developed for the
acquisition, processing and analyzing three-dimensional signal. The
vibration envelope analysis is proposed to detect the cutting capacity
of the tool with the optimization application of cutting parameters.
The research is focused on Hilbert transform optimization to evaluate
the dynamic behavior of the machine/ tool/workpiece.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: Current trends in manufacturing are characterized by
production broadening, innovation cycle shortening, and the products
having a new shape, material and functions. The production strategy
focused on time needed change from the traditional functional
production structure to flexible manufacturing cells and lines.
Production by automated manufacturing system (AMS) is one of the
most important manufacturing philosophies in the last years. The
main goals of the project we are involved in lies on building a
laboratory in which will be located a flexible manufacturing system
consisting of at least two production machines with NC control
(milling machines, lathe). These machines will be linked to a
transport system and they will be served by industrial robots. Within
this flexible manufacturing system a station for the quality control
consisting of a camera system and rack warehouse will be also
located. The design, analysis and improvement of this manufacturing
system, specially with a special focus on the communication among
devices constitute the main aims of this paper. The key determining
factors for the manufacturing system design are: the product, the
production volume, the used machines, the disposable manpower, the
disposable infrastructure and the legislative frame for the specific
cases.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.