Abstract: This article discusses the benefit cost analysis aspects of millimetre wavebands (mmWaves) and Super High Frequency (SHF). The devaluation along the distance of the carrier-to-noise-plus-interference ratio with the coverage distance is assessed by considering two different path loss models, the two-slope urban micro Line-of-Sight (UMiLoS) for the SHF band and the modified Friis propagation model, for frequencies above 24 GHz. The equivalent supported throughput is estimated at the 5.62, 28, 38, 60 and 73 GHz frequency bands and the influence of carrier-to-noise-plus-interference ratio in the radio and network optimization process is explored. Mostly owing to the lessening caused by the behaviour of the two-slope propagation model for SHF band, the supported throughput at this band is higher than at the millimetre wavebands only for the longest cell lengths. The benefit cost analysis of these pico-cellular networks was analysed for regular cellular topologies, by considering the unlicensed spectrum. For shortest distances, we can distinguish an optimal of the revenue in percentage terms for values of the cell length, R ≈ 10 m for the millimeter wavebands and for longest distances an optimal of the revenue can be observed at R ≈ 550 m for the 5.62 GHz. It is possible to observe that, for the 5.62 GHz band, the profit is slightly inferior than for millimetre wavebands, for the shortest Rs, and starts to increase for cell lengths approximately equal to the ratio between the break-point distance and the co-channel reuse factor, achieving a maximum for values of R approximately equal to 550 m.
Abstract: In this paper, a microstrip antenna array is designed for 5G applications. A corporate series feed is considered to operate with a center frequency between 27 to 28 GHz to be able to cover the 5G frequency bands 24.25-27.5 GHz, 26.5-29.5 GHz and 27.5-28.35 GHz. The substrate is taken to be Rogers RT/Duroid 6002. The corporate series 5G antenna array is designed stage by stage by taking into consideration a conventional antenna designed at 28 GHz, thereby constructing the 2X1 antenna array before arriving at the final design structure of 4-element corporate series feed antenna array. The discussions concerning S11 parameter, gain and voltage standing wave ratio (VSWR) for the design structures are considered and all the important findings are tabulated. The proposed antenna array’s S11 parameter was found to be -29.00 dB at a frequency of 27.39 GHz with a good directional gain of 12.12 dB.
Abstract: The paper describes the design and simulation of dual-polarization antennas that use the resonance and radiating properties of the H00 mode of metal open waveguides. The proposed antennas are formed by two orthogonal slots in a finite conducting ground plane. The slots are backed by metal screens connected to the ground plane forming open waveguides. It has been shown that the antenna designs can be efficiently used in mm-wave bands. The antenna single mode operational bandwidth is higher than 10%. The antenna designs are very simple and low-cost. They allow flush installation and can be efficiently used in various communication and remote sensing devices on fast moving carriers. Mutual coupling between antennas of the proposed design is very low. Thus, multiple antenna structures with proposed antennas can be efficiently employed in multi-band and in multiple-input-multiple-output (MIMO) systems.
Abstract: The propagation of microwave is affected by rain and dust particles causing signal attenuation and de-polarization. Computations of these effects require knowledge of the propagation characteristics of microwave and millimeter wave energy in the climate conditions of the studied region. This paper presents effect of wind and humidity on wireless communication such as microwave links in the North West region of Libya (Al-Khoms). The experimental procedure is done on three selected antennae towers (Nagaza station, Al-Khoms center station, Al-Khoms gateway station) for determining the attenuation loss per unit length and cross-polarization discrimination (XPD) change. Dust particles are collected along the region of the study, to measure the particle size distribution (PSD), calculate the concentration, and chemically analyze the contents, then the dielectric constant can be calculated. The results show that humidity and dust, antenna height and the visibility affect both attenuation and phase shift; in which, a few considerations must be taken into account in the communication power budget.
Abstract: A simple design of array antenna is presented in this paper, supporting millimeter wave applications which can be used in short range wireless communications such as 5G applications. This design enhances the use of V-band, according to IEEE standards, as the antenna works in the 70 GHz band with bandwidth more than 11 GHz and peak gain more than 13 dBi. The design is simulated using different numerical techniques achieving a very good agreement.
Abstract: In this paper, a vivid simulated study has been made on 35 GHz Ka-band window frequency in order to judge and compare the DC and high frequency properties of cubic ZnB-GaN with the existing hexagonal 4H-SiC. A flat profile p+pnn+ DDR structure of impatt is chosen and is optimized at a particular bias current density with respect to efficiency and output power taking into consideration the effect of mobile space charge also. The simulated results obtained reveals the strong potentiality of impatts based on both cubic ZnB-GaN and hexagonal 4H-SiC. The DC-to-millimeter wave conversion efficiency for cubic ZnB-GaN impatt obtained is 50% with an estimated output power of 2.83 W at an optimized bias current density of 2.5×108 A/m2. The conversion efficiency and estimated output power in case of hexagonal 4H-SiC impatt obtained is 22.34% and 40 W respectively at an optimum bias current density of 0.06×108 A/m2.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: In this paper, the link quality in SHF and EHF ranges
are studied. In order to achieve high data rate higher frequencies must
be used – centimeter waves (SHF), millimeter waves (EHF) or optical
range. However, there are significant problem when a radio link work
in that diapason – rain attenuation and attenuation in earth-s
atmosphere. Based on statistical rain rates data for Bulgaria, the link
availability can be determined, depending on the working frequency,
the path length and the Power Budget of the link. For the calculations
of rain attenuation and atmosphere-s attenuation the ITU
recommendations are used.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: The main objectif of this paper is to present a tool that
we have developed subject to characterize and modelling indoor radio
channel propagation at millimetric wave. The tool is based on the
ray tracing technique (RTT). As, in realistic environment we cannot
neglect the significant impact of Human Body Shadowing and other
objects in motion on indoor 60 GHz propagation channel. Hence,
our proposed model allows a simulation of propagation in a dynamic
indoor environment. First, we describe a model of human body.
Second, RTT with this model is used to simulate the propagation
of millimeter waves in the presence of persons in motion. Results
of the simulation show that this tool gives results in agreement with
those reported in the literature. Specially, the effects of people motion
on temporal channel properties.
Abstract: A way of generating millimeter wave I/Q signal using inductive resonator matched poly-phase filter is suggested. Normally the poly-phase filter generates quite accurate I/Q phase and magnitude but the loss of the filter is considerable due to series connection of passive RC components. This loss term directly increases system noise figure when the poly-phase filter is used in RF Front-end. The proposed matching method eliminates above mentioned loss and in addition provides gain on the passive filter. The working algorithm is illustrated by mathematical analysis. The generated I/Q signal is used in implementing millimeter wave phase shifter for the 60 GHz communication system to verify its effectiveness. The circuit is fabricated in 90 nm TSMC RF CMOS process under 1.2 V supply voltage. The measurement results showed that the suggested method improved gain by 6.5 dB and noise by 2.3 dB. The summary of the proposed I/Q generation is compared with previous works.
Abstract: Performance of millimeter-wave (mm-wave) multiband
orthogonal frequency division multiplexing (MB-OFDM) ultrawideband
(UWB) signal generation using frequency quadrupling
technique and transmission over fiber is experimentally investigated.
The frequency quadrupling is achived by using only one Mach-
Zehnder modulator (MZM) that is biased at maximum transmission
(MATB) point. At the output, a frequency quadrupling signal is
obtained then sent to a second MZM. This MZM is used for MBOFDM
UWB signal modulation. In this work, we demonstrate 30-
GHz mm-wave wireless that carries three-bands OFDM UWB
signals, and error vector magnitude (EVM) is used to analyze the
transmission quality. It is found that our proposed technique leads to
an improvement of 3.5 dB in EVM at 40% of local oscillator (LO)
modulation with comparison to the technique using two cascaded
MZMs biased at minimum transmission (MITB) point.