Abstract: Wood pyrolysis for Casuarina glauca, Casuarina cunninghamiana, Eucalyptus camaldulensis, Eucalyptus microtheca was made at 450°C with 2.5°C/min. in a flowing N2-atmosphere. The Eucalyptus genus wood gave higher values of specific gravity, ash , total extractives, lignin, N2-liquid trap distillate (NLTD) and water trap distillate (WSP) than those for Casuarina genus. The GHC of NLTD was higher for Casuarina genus than that for Eucalyptus genus with the highest value for Casuarina cunninghamiana. Guiacol, 4-ethyl-2-methoxyphenol and syringol were observed in the NLTD of all the four wood species reflecting their parent hardwood lignin origin. Eucalyptus camaldulensis wood had the highest lignin content (28.89%) and was pyrolyzed to the highest values of phenolics (73.01%), guaiacol (11.2%) and syringol (32.28%) contents in methylene chloride fraction (MCF) of NLTD. Accordingly, recoveries of syringol and guaiacol may become economically attractive from Eucalyptus camaldulensis.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).
Abstract: The mechanical behavior of porous media is governed by the interaction between its solid skeleton and the fluid existing inside its pores. The interaction occurs through the interface of gains and fluid. The traditional analysis methods of porous media, based on the effective stress and Darcy's law, are unable to account for these interactions. For an accurate analysis, the porous media is represented in a fluid-filled porous solid on the basis of the Biot theory of wave propagation in poroelastic media. In Biot formulation, the equations of motion of the soil mixture are coupled with the global mass balance equations to describe the realistic behavior of porous media. Because of irregular geometry, the domain is generally treated as an assemblage of fmite elements. In this investigation, the numerical formulation for the field equations governing the dynamic response of fluid-saturated porous media is analyzed and employed for the study of transient wave motion. A finite element model is developed and implemented into a computer code called DYNAPM for dynamic analysis of porous media. The weighted residual method with 8-node elements is used for developing of a finite element model and the analysis is carried out in the time domain considering the dynamic excitation and gravity loading. Newmark time integration scheme is developed to solve the time-discretized equations which are an unconditionally stable implicit method Finally, some numerical examples are presented to show the accuracy and capability of developed model for a wide variety of behaviors of porous media.
Abstract: An adaptive neural network controller for
autonomous underwater vehicles (AUVs) is presented in this paper.
The AUV model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
In this regards, a nonlinear neural network is used to approximate the
nonlinear uncertainties of AUV dynamics, thus overcoming some
limitations of conventional controllers and ensure good performance.
The uniform ultimate boundedness of AUV tracking errors and the
stability of the proposed control system are guaranteed based on
Lyapunov theory. Numerical simulation studies for motion control of
an AUV are performed to demonstrate the effectiveness of the
proposed controller.
Abstract: In this study, the dispersion of heavy particles line in
an isotropic and incompressible three-dimensional turbulent flow has
been studied using the Kinematic Simulation techniques to find out
the evolution of the line fractal dimension. The fractal dimension of
the line is found in the case of different particle gravity (in practice,
different values of particle drift velocity) in the presence of small
particle inertia with a comparison with that obtained in the diffusion
case of material line at the same Reynolds number. It can be
concluded for the dispersion of heavy particles line in turbulent flow
that the particle gravity affect the fractal dimension of the line for
different particle gravity velocities in the range 0.2 < W < 2. With
the increase of the particle drift velocity, the fractal dimension of the
line decreases which may be explained as the particles pass many
scales in their journey in the direction of the gravity and the particles
trajectories do not affect by these scales at high particle drift
velocities.
Abstract: The design of a gravity dam is performed through an
interactive process involving a preliminary layout of the structure
followed by a stability and stress analysis. This study presents a
method to define the optimal top width of gravity dam with genetic
algorithm. To solve the optimization task (minimize the cost of the
dam), an optimization routine based on genetic algorithms (GAs) was
implemented into an Excel spreadsheet. It was found to perform well
and GA parameters were optimized in a parametric study. Using the
parameters found in the parametric study, the top width of gravity
dam optimization was performed and compared to a gradient-based
optimization method (classic method). The accuracy of the results
was within close proximity. In optimum dam cross section, the ratio
of is dam base to dam height is almost equal to 0.85, and ratio of dam
top width to dam height is almost equal to 0.13. The computerized
methodology may provide the help for computation of the optimal
top width for a wide range of height of a gravity dam.
Abstract: Because of the reservoir effect, dynamic analysis of concrete dams is more involved than other common structures. This problem is mostly sourced by the differences between reservoir water, dam body and foundation material behaviors. To account for the reservoir effect in dynamic analysis of concrete gravity dams, two methods are generally employed. Eulerian method in reservoir modeling gives rise to a set of coupled equations, whereas in Lagrangian method, the same equations for dam and foundation structure are used. The Purpose of this paper is to evaluate and study possible advantages and disadvantages of both methods. Specifically, application of the above methods in the analysis of dam-foundationreservoir systems is leveraged to calculate the hydrodynamic pressure on dam faces. Within the frame work of dam- foundationreservoir systems, dam displacement under earthquake for various dimensions and characteristics are also studied. The results of both Lagrangian and Eulerian methods in effects of loading frequency, boundary condition and foundation elasticity modulus are quantitatively evaluated and compared. Our analyses show that each method has individual advantages and disadvantages. As such, in any particular case, one of the two methods may prove more suitable as presented in the results section of this study.
Abstract: Recycling of aluminum alloys often decrease fluidity,
consequently influence the castability of the alloy. In this study, the
fluidity of Al-Zn alloys, such as the standard A713 alloy with and
without scrap addition has been investigated. The scrap added was
comprised of contaminated alloy turning chips. Fluidity
measurements were performed with double spiral fluidity test
consisting of gravity casting of double spirals in green sand moulds
with good reproducibility. The influence of recycled alloy on fluidity
has been compared with that of the virgin alloy and the results
showed that the fluidity decreased with the increase in recycled alloy
at minimum pouring temperatures. Interestingly, an appreciable
improvement in the fluidity was observed at maximum pouring
temperature, especially for coated spirals.
Abstract: This research was conducted in the Lower Namkam
Irrigation Project situated in the Namkam River Basin in Thailand.
Degradation of groundwater quality in some areas is caused by saline
soil spots beneath ground surface. However, the tail regulated gate
structure on the Namkam River, a lateral stream of the Mekong
River. It is aimed for maintaining water level in the river at +137.5 to
+138.5 m (MSL) and flow to the irrigation canals based on a gravity
system since July 2009. It might leach some saline soil spots from
underground to soil surface if lack of understanding of the
conjunctive surface water and groundwater behaviors. This research
has been conducted by continuously the observing of both shallow
and deep groundwater level and quality from existing observation
wells. The simulation of surface water was carried out using a
hydrologic modeling system (HEC-HMS) to compute the ungauged
side flow catchments as the lateral flows for the river system model
(HEC-RAS). The constant water levels in the upstream of the
operated gate caused a slight rising up of shallow groundwater level
when compared to the water table. However, the groundwater levels
in the confined aquifers remained less impacted than in the shallow
aquifers but groundwater levels in late of wet season in some wells
were higher than the phreatic surface. This causes salinization of the
groundwater at the soil surface and might affect some crops. This
research aims for the balance of water stage in the river and efficient
groundwater utilization in this area.
Abstract: Support Vector Domain Description (SVDD) is one of the best-known one-class support vector learning methods, in which one tries the strategy of using balls defined on the feature space in order to distinguish a set of normal data from all other possible abnormal objects. As all kernel-based learning algorithms its performance depends heavily on the proper choice of the kernel parameter. This paper proposes a new approach to select kernel's parameter based on maximizing the distance between both gravity centers of normal and abnormal classes, and at the same time minimizing the variance within each class. The performance of the proposed algorithm is evaluated on several benchmarks. The experimental results demonstrate the feasibility and the effectiveness of the presented method.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: In this paper, we discuss the egalitarianism solution (ES) and center-of-gravity of the imputation-set value (CIV) for bicooperative games, which can be seen as the extensions of the solutions for traditional games given by Dutta and Ray [1] and Driessen and Funaki [2]. Furthermore, axiomatic systems for the given values are proposed. Finally, a numerical example is offered to illustrate the player ES and CTV.
Abstract: Participation in global trade means that Chinas vegetables and fruits industry faces international food safety standards and increased scrutiny worldwide. The objectives of this paper were to investigate how existing food safety standards and regulations in the importing countries impact the export of vegetables and fruits from China. This paper discussed the current and historical situations of Chinas vegetables and fruits export from 1996 to 2010, analyzed the Maximum Residual Limit (MRL) standards of pesticides imposed by importing countries, quantitatively estimated the impacts of food safety standards on Chinas vegetables and fruits export based on a gravity model. The results showed that although transportation distance between trade partners and tariff rates on vegetables and fruits were still the importantly resistant factors for China export, vegetables and fruits export was sensitive to the number of regulated pesticides, the strictness, and the level of food safety standards imposed by importing countries, which showed a significant trade flow effect, stricter food safety standards, increased number of regulated pesticides significantly inhibit China export of vegetables and fruits. Moreover, Chinas food safety standards also showed a significantly effect on vegetables and fruits export, which inhibited export to some extent. KeywordsFood safety standards, MRL, Vegetables, Fruits, Export.
Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: This paper presents an analytical solution to get a reliable estimation of the hydrodynamic pressure on gravity dams induced by vertical component earthquake when solving the fluid and dam interaction problem. Presented analytical technique is presented for calculation of earthquake-induced hydrodynamic pressure in the reservoir of gravity dams allowing for water compressibility and wave absorption at the reservoir bottom. This new analytical solution can take into account the effect of bottom material on seismic response of gravity dams. It is concluded that because the vertical component of ground motion causes significant hydrodynamic forces in the horizontal direction on a vertical upstream face, responses to the vertical component of ground motion are of special importance in analysis of concrete gravity dams subjected to earthquakes.
Abstract: In this paper, Steam Assisted Gravity Drainage
(SAGD) is introduced and its advantages over ordinary steam
injection is demonstrated. A simple simulation model is built and
three scenarios of natural production, ordinary steam injection, and
SAGD are compared in terms of their cumulative oil production and
cumulative oil steam ratio. The results show that SAGD can
significantly enhance oil production in quite a short period of time.
However, since the distance between injection and production wells
is short, the oil to steam ratio decreases gradually through time.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: Falls are the primary cause of accidents in people over
the age of 65, and frequently lead to serious injuries. Since the early
detection of falls is an important step to alert and protect the aging
population, a variety of research on detecting falls was carried out
including the use of accelerators, gyroscopes and tilt sensors. In
exiting studies, falls were detected using an accelerometer with
errors. In this study, the proposed method for detecting falls was to
use two accelerometers to reject wrong falls detection. As falls are
accompanied by the acceleration of gravity and rotational motion, the
falls in this study were detected by using the z-axial acceleration
differences between two sites. The falls were detected by calculating
the difference between the analyses of accelerometers placed on two
different positions on the chest of the subject. The parameters of the
maximum difference of accelerations (diff_Z) and the integration of
accelerations in a defined region (Sum_diff_Z) were used to form the
fall detection algorithm. The falls and the activities of daily living
(ADL) could be distinguished by using the proposed parameters
without errors in spite of the impact and the change in the positions
of the accelerometers. By comparing each of the axial accelerations,
the directions of falls and the condition of the subject afterwards
could be determined.In this study, by using two accelerometers
without errors attached to two sites to detect falls, the usefulness of
the proposed fall detection algorithm parameters, diff_Z and
Sum_diff_Z, were confirmed.