Abstract: The paper presents the brief information on particular results of experimental study focused to the problems of behavior of structural plated components made of fiber-cement-based materials and used in building constructions, exposed to atmospheric physical effects given by the weather changes in the summer period. Weather changes represented namely by temperature and rain cause also the changes of the temperature and moisture of the investigated structural components. This can affect their static behavior that means stresses and deformations, which have been monitored as the main outputs of tests performed. Experimental verification is based on the simulation of the influence of temperature and rain using the defined procedure of warming and water sprinkling with respect to the corresponding weather conditions during summer period in the South Moravian region at the Czech Republic, for which the application of these structural components is mainly planned. Two types of components have been tested: (i) glass-fiber-concrete panels used for building façades and (ii) fiber-cement slabs used mainly for claddings, but also as a part of floor structures or lost shuttering, and so on.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Integration of process planning and scheduling
functions is necessary to achieve superior overall system
performance. This paper proposes a methodology for integration of
process planning and scheduling for prismatic component that can be
implemented in a company with existing departments. The developed
model considers technological constraints whereas available time for
machining in shop floor is the limiting factor to produce multiple
process plan (MPP). It takes advantage of MPP while guarantied the
fulfillment of the due dates via using overtime. This study has been
proposed to determinate machining parameters, tools, machine and
amount of over time within the minimum cost objective while
overtime is considered for this. At last the illustration shows that the
system performance is improved by as measured by cost and
compatible with due date.
Abstract: The previous proposed evacuation routing approaches usually divide the space into multiple interlinked zones. However, it may be harder to clearly and objectively define the margins of each zone. This paper proposes an approach that connects locations of necessary guidance into a spatial network. In doing so, evacuation routes can be constructed based on the links between starting points, turning nodes, and terminal points. This approach more conforms to the real-life evacuation behavior. The feasibility of the proposed approach is evaluated through a case of one floor in a hospital building. Results indicate that the proposed approach provides valuable suggestions for evacuation planning.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: Previous studies mass evacuation route network does
not fully reflect the step-by-step behavior and evacuees make routing
decisions. Therefore, they do not work as expected when applied to the
evacuation route planning is valid. This article describes where
evacuees may have to make a direction to select all areas were
identified as guiding points to improve evacuation routes network.
This improved route network can be used as a basis for the layout can
be used to guide the signs indicate that provides the required
evacuation direction. This article also describes that combines
simulation and artificial bee colony algorithm to provide the proposed
routing solutions, to plan an integrated routing mode. The improved
network and the model used is the cinema as a case study to assess the
floor. The effectiveness of guidance solution in the total evacuation
time is significant by verification.
Abstract: In recent years, tuned mass damper (TMD) control systems for civil engineering structures have attracted considerable attention. This paper emphasizes on the application of particle swarm application (PSO) to design and optimize the parameters of the TMD control scheme for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using the PSO technique which has a story ability to find the most optimistic results. An 11- story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed method. The results analysis through the time-domain simulation and some performance indices reveals that the designed PSO based TMD controller has an excellent capability in reduction of the seismically excited example building.
Abstract: For stable bipedal gait generation on the level floor,
efficient restoring of mechanical energy lost by heel collision at
the ground is necessary. Parametric excitation principle is one of
the solutions. We dealt with the robot-s total center of mass as
an inverted pendulum to consider the total dynamics of the robot.
Parametrically excited walking requires the use of continuous target
trajectory that is close to discontinuous optimal trajectory. In this
paper, we proposed the new target trajectory based on a position
in the walking direction. We surveyed relations between walking
performance and the parameters that form the target trajectory via
numerical simulations. As a result, it was found that our target
trajectory has the similar characteristics of a parametrically excited
inverted pendulum.
Abstract: The concept of flexible manufacturing is highly
appealing in gaining a competitive edge in the market by quickly
adapting to the changing customer needs. Scheduling jobs on flexible
manufacturing systems (FMSs) is a challenging task of managing the
available flexibility on the shop floor to react to the dynamics of the
environment in real-time. In this paper, an agent-oriented scheduling
framework that can be integrated with a real or a simulated FMS is
proposed. This framework works in stochastic environments with a
dynamic model of job arrival. It supports a hierarchical cooperative
scheduling that builds on the available flexibility of the shop floor.
Testing the framework on a model of a real FMS showed the
capability of the proposed approach to overcome the drawbacks of
the conventional approaches and maintain a near optimal solution
despite the dynamics of the operational environment.
Abstract: This study analyses store layout among the many
factors that underlie supermarket store design, this; in terms of what to
display in a shop and where to place the items. This report examines
newly-opened stores and evaluates their interior shop floor layouts,
which we then attempt to categorize by various styles. We then
consider the interaction between shop floor layout and customer
behavior from the perspective of the supermarket as the seller. At this
point, we focus on the “store magnets"–the main sections within the
shop likely to attract customers into the store.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In this study an extensive experimental research is
carried out to develop a better understanding of the effects of Piano Key (PK) weir geometry on weir flow threshold submergence.
Experiments were conducted in a 12 m long, 0.4 m wide and 0.7 m deep rectangular glass wall flume. The main objectives were to
investigate the effect of the PK weir geometries including the weir
length, weir height, inlet-outlet key widths, upstream and
downstream apex overhangs, and slopped floors on threshold submergence and study the hydraulic flow characteristics. From the
experimental results, a practical formula is proposed to evaluate the flow threshold submergence over PK weirs.
Abstract: Facing the concern of the population to its environment and to climatic change, city planners are now considering the urban climate in their choices of planning. The urban climate, representing different urban morphologies across central Bangkok metropolitan area (BMA), are used to investigates the effects of both the composition and configuration of variables of urban morphology indicators on the summer diurnal range of urban climate, using correlation analyses and multiple linear regressions. Results show first indicate that approximately 92.6% of the variation in the average maximum daytime near-surface air temperature (Ta) was explained jointly by the two composition variables of urban morphology indicators including open space ratio (OSR) and floor area ratio (FAR). It has been possible to determine the membership of sample areas to the local climate zones (LCZs) using these urban morphology descriptors automatically computed with GIS and remote sensed data. Finally result found the temperature differences among zones of large separation, such as the city center could be respectively from 35.48±1.04ºC (Mean±S.D.) warmer than the outskirt of Bangkok on average for maximum daytime near surface temperature to 28.27±0.21ºC for extreme event and, can exceed as 8ºC. A spatially disaggregation of urban thermal responsiveness map would be helpful for several reasons. First, it would localize urban areas concerned by different climate behavior over summer daytime and be a good indicator of urban climate variability. Second, when overlaid with a land cover map, this map may contribute to identify possible urban management strategies to reduce heat wave effects in BMA.
Abstract: The product development process (PDP) in the
Technology group plays a very important role in the launch of any
product. While a manufacturing process encourages the use of certain
measures to reduce health, safety and environmental (HSE) risks on
the shop floor, the PDP concentrates on the use of Geometric
Dimensioning and Tolerancing (GD&T) to develop a flawless design.
Furthermore, PDP distributes and coordinates activities between
different departments such as marketing, purchasing, and
manufacturing. However, it is seldom realized that PDP makes a
significant contribution to developing a product that reduces HSE
risks by encouraging the Technology group to use effective GD&T.
The GD&T is a precise communication tool that uses a set of
symbols, rules, and definitions to mathematically define parts to be
manufactured. It is a quality assurance method widely used in the oil
and gas sector. Traditionally it is used to ensure the
interchangeability of a part without affecting its form, fit, and
function. Parts that do not meet these requirements are rejected
during quality audits.
This paper discusses how the Technology group integrates this
quality assurance tool into the PDP and how the tool plays a major
role in helping the HSE department in its goal towards eliminating
HSE incidents. The PDP involves a thorough risk assessment and
establishes a method to address those risks during the design stage.
An illustration shows how GD&T helped reduce safety risks by
ergonomically improving assembling operations. A brief discussion
explains how tolerances provided on a part help prevent finger injury.
This tool has equipped Technology to produce fixtures, which are
used daily in operations as well as manufacturing. By applying
GD&T to create good fits, HSE risks are mitigated for operating
personnel. Both customers and service providers benefit from
reduced safety risks.
Abstract: This paper explains the cause of nonlinearity in floor
attenuation hither to left unexplained. The performance degradation
occurring in air interface for GSM signals is quantitatively analysed
using the concept of Radiating Columns of buildings. The signal
levels were measured using Wireless Network Optimising Drive Test
Tool (E6474A of Agilent Technologies). The measurements were
taken in reflected signal environment under usual fading conditions
on actual GSM signals radiated from base stations. A mathematical
model is derived from the measurements to predict the GSM signal
levels in different floors. It was applied on three buildings and found
that the predicted signal levels deviated from the measured levels
with in +/- 2 dB for all floors. It is more accurate than the prediction
models based on Floor Attenuation Factor. It can be used for
planning proper indoor coverage in multi storey buildings.
Abstract: This paper presents an application of 5S lean technology to a production facility. Due to increased demand, high product variety, and a push production system, the plant has suffered from excessive wastes, unorganized workstations, and unhealthy work environment. This has translated into increased production cost, frequent delays, and low workers morale. Under such conditions, it has become difficult, if not impossible, to implement effective continuous improvement studies. Hence, the lean project is aimed at diagnosing the production process, streamlining the workflow, removing/reducing process waste, cleaning the production environment, improving plant layout, and organizing workstations. 5S lean technology is utilized for achieving project objectives. The work was a combination of both culture changes and tangible/physical changes on the shop floor. The project has drastically changed the plant and developed the infrastructure for a successful implementation of continuous improvement as well as other best practices and quality initiatives.
Abstract: The effect of beak trimming on behavior of two strains
of Thai native pullets kept in floor pens was studied. Six general
activities (standing, crouching, moving, comforting, roosting, and
nesting), 6 beak related activities (preening, feeding, drinking,
pecking at inedible object, feather pecking, and litter pecking), and 4
agonistic activities (head pecking, threatening, avoiding, and fighting)
were measured twice a for 15 consecutive days, started when the
pullets were 19 wk old. It was found that beak trimmed pullets drank
more frequent (P
Abstract: The performance of schedules released to a shop floor may greatly be affected by unexpected disruptions. Thus, this paper considers the flexible job shop scheduling problem when processing times of some operations are represented by a uniform distribution with given lower and upper bounds. The objective is to find a predictive schedule that can deal with this uncertainty. The paper compares two genetic approaches to obtain predictive schedule. To determine the performance of the predictive schedules obtained by both approaches, an experimental study is conducted on a number of benchmark problems.
Abstract: In this work, the plate bending formulation of the boundary element method - BEM, based on the Reissner?s hypothesis, is extended to the analysis of plates reinforced by beams taking into account the membrane effects. The formulation is derived by assuming a zoned body where each sub-region defines a beam or a slab and all of them are represented by a chosen reference surface. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to reduce the number of degrees of freedom, the problem values defined on the interfaces are written in terms of their values on the beam axis. Initially are derived separated equations for the bending and stretching problems, but in the final system of equations the two problems are coupled and can not be treated separately. Finally are presented some numerical examples whose analytical results are known to show the accuracy of the proposed model.