Abstract: Synthetic oily wastewaters were prepared from metal working fluids (MWF). Electrocoagulation experiments were performed under constant voltage application. The current, conductivity, pH, dissolved oxygen concentration and temperature were recorded on line at every 5 seconds during the experiments. Effects of applied voltage differences, electrode materials and distance between electrodes on removal efficiency have been investigated. According to the experimental results, the treatment of MWF wastewaters by iron electrodes rather than aluminum and stainless steel was much quicker; and the distance between electrodes should be less than 1cm. The electrocoagulation process was modeled by using block oriented approach and found out that it can be modeled as a single input and multiple output system. Modeling studies indicates that the electrocoagulation process has a nonlinear model structure.
Abstract: The tribological outcomes of micro dent are found to be outstanding in many engineering and natural surfaces. Ceramic (Al2O3) is considered one of the most potential material to bearing surfaces particularly, artificial hip or knee implant. A well-defined micro dent on alumina oxide interface could further decrease friction and wear rate, thus increase their stability and durability. In this study we fabricated circular micro dent surface profiles (Dia: 400µm, Depth 20µm, P: 1.5mm; Dia: 400µm, Depth 20µm, P: 2mm) on pure Al2O3 (99.6%) substrate by using a micro tool machines. A preliminary tribological experiment was carried out to compare friction coefficient of these fabricated dent surfaces with that of non-textured surfaces. The experiment was carried on well know pin-on-disk specimens while other experimental parameters such as hertz pressure, speed, lubrication, and temperature were maintained to standard of simulated hip joints condition. The experiment results revealed that micro dent surface texture reduced 15%, 8% and 4% friction coefficient under 0.132,0.162, 0.187 GPa contact pressure respectively. Since this is a preliminary tribological study, we will pursue further experiments considering higher ranges of dent profiles and longer run experiments. However, the preliminary results confirmed the suitability of fabricating dent profile to ceramic surfaces by using micro tooling, and also their improved tribological performance in simulated hip joints.
Abstract: No negative control nor control to prevent microbes from escaping was set when the S-shaped flask experiments were performed by Pasteur. Microscope was not used to observe the media in the flasks. Louis Pasteur’s S-shaped flask experiment was re-examined by using U-shaped flasks, modified S-shaped flasks and microscope. A mixture of microbes was isolated from the room air, from which one rod-shaped Bacillus species with proposed name Bacillus gaso-mobilis sp nov and one grape-shaped Staphylococcus species with proposed name of Staphylococcus gaso-mobilis sp nov were identified. Their penicillin and ampicillin resistant strains containing plasmids were isolated. These bacteria could change color, produce odor and automatically move in the air. They did not form colonies on solid media. They had a high suspension capacity in liquid media. Their light absorbance peaked at the wave length of 320 nm. It was concluded that there were flaws with Louis Pasteur’s S-shaped flask experiments.
Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: In-situ chemical oxidation (ISCO) has been widely
used for source zone remediation of Dense Nonaqueous Phase
Liquids (DNAPLs) in subsurface environments. DNAPL source
zones for karst aquifers are generally located in epikarst where the
DNAPL mass is trapped either in karst soil or at the regolith contact
with carbonate bedrock. This study aims to investigate the
performance of oxidation of residual trichloroethylene found in such
environments by potassium permanganate. Batch and flow cell
experiments were conducted to determine the kinetics and the mass
removal rate of TCE. pH change, Cl production, TCE and MnO4
destruction were monitored routinely during experiments. Nonreactive
tracer tests were also conducted prior and after the oxidation
process to determine the influence of oxidation on flow conditions.
The results show that oxidant consumption rate of the calcareous
epikarst soil was significant and the oxidant demand was determined
to be 20 g KMnO4/kg soil. Oxidation rate of residual TCE (1.26x10-3
s-1) was faster than the oxidant consumption rate of the soil (2.54 -
2.92x10-4 s-1) at only high oxidant concentrations (> 40 mM
KMnO4). Half life of TCE oxidation ranged from 7.9 to 10.7 min.
Although highly significant fraction of residual TCE mass in the
system was destroyed by permanganate oxidation, TCE
concentration in the effluent remained above its MCL. Flow
interruption tests indicate that efficiency of ISCO was limited by the
rate of TCE dissolution and the rate-limited desorption of TCE. The
residence time and the initial concentration of the oxidant in the
source zone also controlled the efficiency of ISCO in epikarst.
Abstract: Optimization of a microwave-assisted extraction of cherry laurel (Prunus laurocerasus) fruit using methanol was studied. The influence of process parameters (microwave power, plant material-to-solvent ratio and the extraction time) on the extraction efficiency were optimized by using response surface methodology. The predicted maximum yield of extractive substances (41.85 g/100 g fresh plant material) was obtained at microwave power of 600 W and plant material to solvent ratio of 0.2 g/cm3 after 26 minutes of extraction, while a mean value of 40.80±0.41 g/100 g fresh plant material was obtained from laboratory experiments. This proves applicability of the model in predicting optimal extraction conditions with minimal laborious and time consuming. The results indicated that all process parameters were effective on the extraction efficiency, while the most important factor was extraction time. In order to rationalize production the optimal economical condition which gave a large total extract yield with minimal energy and solvent consumption was found.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.
Abstract: Deoxyribonucleic Acid or DNA computing has
emerged as an interdisciplinary field that draws together chemistry,
molecular biology, computer science and mathematics. Thus, in this
paper, the possibility of DNA-based computing to solve an absolute
1-center problem by molecular manipulations is presented. This is
truly the first attempt to solve such a problem by DNA-based
computing approach. Since, part of the procedures involve with
shortest path computation, research works on DNA computing for
shortest path Traveling Salesman Problem, in short, TSP are reviewed.
These approaches are studied and only the appropriate one is adapted
in designing the computation procedures. This DNA-based
computation is designed in such a way that every path is encoded by
oligonucleotides and the path-s length is directly proportional to the
length of oligonucleotides. Using these properties, gel electrophoresis
is performed in order to separate the respective DNA molecules
according to their length. One expectation arise from this paper is that
it is possible to verify the instance absolute 1-center problem using
DNA computing by laboratory experiments.
Abstract: This paper aims at numerically analysing the effect
of an active flow control (AFC) by a vortex generator jet (VGJ)
submerged in a boundary layer via Chimera Grids and Detached-
Eddy Simulation (DES). The performance of DES results are
judged against Reynolds-Averaged Navier-Stokes (RANS) and
compared with the experiments that showed an unsteady vortex
motion downstream of VGJ. Experimental results showed that
the mechanism of embedding logitudinal vortex structure in the
main stream flow is quite effective in increasing the near wall
momentum of separated aircraft wing. In order to simulate such
a flow configuration together with the VGJ, an efficient numerical
approach is required. This requirement is fulfilled by performing
the DES simulation over the flat plate using the DLR TAU Code.
The DES predictions identify the vortex region via smooth hybrid
length scale and predict the unsteady vortex motion observed in
the experiments. The DES results also showed that the sufficient
grid refinement in the vortex region resolves the turbulent scales
downstream of the VGJ, the spatial vortex core postion and nondimensional
momentum coefficient RVx .
Abstract: The effect of flakes from biologically activated hullless barley grain and malt extract on microbiological safety of yoghurt was studied. Pasteurized milk, freeze-dried yoghurt culture YF-L811 (Chr. Hansen, Denmark), flakes from biologically activated hull-less barley grain (Latvia) and malt extract (Ilgezeem, Latvia) were used for experiments. Yoghurt samples with flakes from biologically activated hull-less barley grain and malt extract were analyzed for total plate count of mesophylic aerobic and facultative anaerobic microorganisms, as well yeasts and moulds population during shelflife. Results showed that the changes of pH and titratable acidity affected the concentration of added malt extract. The lowest pH and the highest titratable acidity were determined in samples YFBG5% ME4% and YFBG5% ME6% on the 14th day. The total plate count decreased in all yoghurt samples except sample YFBG5% ME6%, where was determined the increase of microorganisms from 7th till 14th day. The adding of flakes from biologically activated hull-less barley grain in yoghurt samples caused the higher initial content of yeasts and moulds comparing with control. The growth of yeasts and moulds during shelf-life provided the added malt extract in yoghurt samples. Yoghurt enriched with flakes from biologically activated hull-less barley grain and malt extract from a microbiological perspective is safe product.
Abstract: The effect of plant growth-promoting rhizobacteria
(PGPR) on seed germination, seedling growth and yield of field
grown maize were evaluated in three experiments. In these
experiments six bacterial strains include P.putida strain R-168,
P.fluorescens strain R-93, P.fluorescens DSM 50090, P.putida
DSM291, A.lipoferum DSM 1691, A.brasilense DSM 1690 were
used. Results of first study showed seed Inoculation significantly
enhanced seed germination and seedling vigour of maize. In second
experiment, leaf and shoot dry weight and also leaf surface area
significantly were increased by bacterial inoculation in both sterile
and non-sterile soil. The results showed that inoculation with
bacterial treatments had a more stimulating effect on growth and
development of plants in nonsterile than sterile soil. In the third
experiment, Inoculation of maize seeds with all bacterial strains
significantly increased plant height, 100 seed weight, number of seed
per ear and leaf area .The results also showed significant increase in
ear and shoot dry weight of maize.
Abstract: Fruit drying is a well known process mostly used for
preservation of fruits. Osmotic dehydration of apricot slices were
carried out in three different salt-sucrose concentrations and four
different temperatures. Also three different weight ratios of solution
to sample were conducted to one set of experiments. The dehydration
curves were constructed using Peleg-s model. Increasing the solution
volume increased the mass transfer rate and hence the solid gain
increased rapidly. Increasing the volume of osmotic media caused an
increase in overall mass transfer but a 'solution to sample' ratio of 5:1
gave the best product quality. The best temperature and concentration
that had a high water loss to solid gain ratio and an acceptable taste
were 40°C and 5%, respectively.
Abstract: This study focuses on emission of black carbon (BC)
from field open burning of corn residues. Real-time BC
concentration was measured by Micro Aethalometer from field
burning and simulated open burning in a chamber (SOC)
experiments. The average concentration of BC was 1.18±0.47 mg/m3
in the field and 0.89±0.63 mg/m3 in the SOC. The deduced emission
factor from field experiments was 0.50±0.20 gBC/kgdm, and 0.56±0.33
gBC/kgdm from SOC experiment, which are in good agreement with
other studies. In 2007, the total burned area of corn crop was 8,000
ha, resulting in an emission load of BC 20 ton corresponding to 44.5
million kg CO2 equivalent. Therefore, the control of open burning in
corn field represents a significant global warming reduction option.
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: carrot is one of the important root vegetable crops,
and it is highly nutritious as it contains appreciable amount of
vitamins, minerals and β-carotene. The major objective of current
research was to evaluate the chemical composition of carrot variety
'Nante' hybrids in general and to select the best samples for fresh-cut
salad production. The research was accomplished on fresh in Latvia
cultivated carrots harvested in Zemgale region in the first part of
October, 2011 and immediately used for experiments. Late-bearing
variety 'Nante' hybrid carrots were used for analysis:
'Nante/Berlikum', 'Nante/Maestro', 'Nante/Forto', 'Nante/Bolero'
and 'Nante/Champion'. The quality parameters as moisture, soluble
solid, firmness, b-carotene, carotenoid, color, polyphenols, total
phenolic compounds and total antioxidant capacity were analyzed
using standard methods. For fresh-cut salad production as more
applicable could be recommended hybrids 'Nante/Forto' and
'Nante/Berlikum' - mainly because it-s higher nutritive value, as
higher total phenolic compounds, polyphenols and pronounced
antioxidant capacity.
Abstract: In online context, the design and implementation of
effective remote laboratories environment is highly challenging on
account of hardware and software needs. This paper presents the
remote laboratory software framework modified from ilab shared
architecture (ISA). The ISA is a framework which enables students to
remotely acccess and control experimental hardware using internet
infrastructure. The need for remote laboratories came after
experiencing problems imposed by traditional laboratories. Among
them are: the high cost of laboratory equipment, scarcity of space,
scarcity of technical personnel along with the restricted university
budget creates a significant bottleneck on building required
laboratory experiments. The solution to these problems is to build
web-accessible laboratories. Remote laboratories allow students and
educators to interact with real laboratory equipment located
anywhere in the world at anytime. Recently, many universities and
other educational institutions especially in third world countries rely
on simulations because they do not afford the experimental
equipment they require to their students. Remote laboratories enable
users to get real data from real-time hand-on experiments. To
implement many remote laboratories, the system architecture should
be flexible, understandable and easy to implement, so that different
laboratories with different hardware can be deployed easily. The
modifications were made to enable developers to add more
equipment in ISA framework and to attract the new developers to
develop many online laboratories.
Abstract: Simulations play a major role in education not only because they provide realistic models with which students can interact to acquire real world experiences, but also because they constitute safe environments in which students can repeat processes without any risk in order to perceive easier concepts and theories. Virtual reality is widely recognized as a significant technological advance that can facilitate learning process through the development of highly realistic 3D simulations supporting immersive and interactive features. The objective of this paper is to analyze the influence of virtual reality-s use in chemistry instruction as well as to present an integrated web-based learning environment for the simulation of chemical experiments. The proposed application constitutes a cost-effective solution for both schools and universities without appropriate infrastructure and a valuable tool for distance learning and life-long education in chemistry. Its educational objectives are the familiarization of students with the equipment of a real chemical laboratory and the execution of virtual volumetric analysis experiments with the active participation of students.
Abstract: In this paper we proposed two new confidence intervals for the normal population mean with known coefficient of variation. This situation occurs normally in environment and agriculture experiments where the scientist knows the coefficient of variation of their experiments. We propose two new confidence intervals for this problem based on the recent work of Searls [5] and the new method proposed in this paper for the first time. We derive analytic expressions for the coverage probability and the expected length of each confidence interval. Monte Carlo simulation will be used to assess the performance of these intervals based on their expected lengths.
Abstract: In this work, the results of mixing study by a jet mixer in a tank have been investigated in the laboratory scale. The tank dimensions are H/D=1 and the jet entrance have been considered in
the center of upper surface of tank. RNG-k-ε model is used as the
turbulent model for the prediction of the pattern of turbulent flow
inside the tank. For this purpose, a tank with volume of 110 liter is
simulated and it has been divided into 410,000 tetrahedral control
cells for performing the calculations. The grids at the vicinity of the
nozzle and suction pare are finer to get more accurate results. The
experimental results showed that in a vertical jet, the lowest mixing
time takes place at 35 degree. In addition, mixing time decreased by
increasing the Reynolds number. Furthermore, the CFD simulation
predicted the items as well a flow patterns precisely that validates the
experiments.
Abstract: Independent component analysis can estimate unknown
source signals from their mixtures under the assumption that the
source signals are statistically independent. However, in a real environment,
the separation performance is often deteriorated because
the number of the source signals is different from that of the sensors.
In this paper, we propose an estimation method for the number of
the sources based on the joint distribution of the observed signals
under two-sensor configuration. From several simulation results, it
is found that the number of the sources is coincident to that of
peaks in the histogram of the distribution. The proposed method can
estimate the number of the sources even if it is larger than that of
the observed signals. The proposed methods have been verified by
several experiments.